Performance of Lightweight Concrete with Expansive and Air-Entraining Admixtures in CFST Columns
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 6
Abstract
Adequate load transfer in concrete-filled steel tubes (CFSTs) requires a close interaction between the steel walls and the concrete core. The present work analyzes the adhesion and confinement effects in steel tubes promoted by three types of lightweight concrete: without any admixture (reference), with an expansive agent (EA), and with an air-entraining admixture (AEA). The following tests were performed: expanding the potential of the admixtures, characterization of the hardened concretes, shear tests, axial compression with load applied to the concrete core, and axial compression applied to the mixed section. The results indicated that the dimensional variation generated by the EA induces a confinement prestress, which improves interface adhesion and, thus, the performance of the CFST. The concrete with AEA presented a lower modulus of elasticity and superficial irregularities that contributed to the manifestation of mechanic adhesion, adhesion by friction, and a high degree of confinement. Although the AEA-CFSTs presented compressive strength 2% lower than the reference, they were 10% lighter. On the other hand, the EA-CFST presented a similar density and an 8% increase in the compressive strength. In conclusion, the use of both admixtures contributed to a suitable performance of the filling cores.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We gratefully acknowledge the agencies CAPES and Fundação Gorceix for providing financial support. We are also grateful for the infrastructure and collaboration of the Research Group on Solid Wastes—RECICLOS—CNPq. The authors would like to acknowledge the Laboratory of Structures, Escola de Minas, Universidade Federal de Ouro Preto (UFOP), MG, Brazil, for providing equipment and technical support for the experiments.
References
ABNT (Brazilian Association of Technical Standards). 1996. Portland cement—Determination of compressive strength. NBR 7215. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2005. Hardened mortar and concrete—Determination of absorption, voids and specific gravity. NBR 9778. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2007. Concrete—Compressive test of cylindric specimens—Method of test. NBR 5739. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2008a. Concrete—Determination of the elasticity modulus by compression. NBR 8522. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2008b. Concrete—Procedure for molding and curing of specimens. NBR 5738. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2013. Hardened concrete—Determination of ultrasonic wave transmission velocity. NBR 8802. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2018. Portland cement—Requirements. NBR 16697. Rio de Janeiro, Brazil: ABNT.
ACI (American Concrete Institute). 2013. Nondestructive test methods for evaluation of concrete in structures. ACI 228.2R. Farmington Hills, MI: ACI.
Alengaram, U. J., H. Mahmud, and M. Z. Jumaat. 2010. “Comparison of mechanical and bond properties of oil palm kernel shell concrete with normal weight concrete.” Int. J. Phys. Sci. 5 (8): 1231–1239.
Assi, I. M., E. M. Qudeimat, and Y. Hunaiti. 2003. “Ultimate moment capacity of foamed and lightweight aggregate concrete-filled steel tubes.” Steel Compos. Struct. 3 (3): 199–212. https://doi.org/10.12989/scs.2003.3.3.199.
ASTM. 2012. Standard test method for density and void content of hardened pervious concrete. ASTM C1754/C1754M. West Conshohocken, PA: ASTM.
ASTM. 2013. Standard test method for measurement of rate of absorption of water by hydraulic-cement concretes. ASTM C1585. West Conshohocken, PA: ASTM.
ASTM. 2014a. Standard test method for fundamental transverse, longitudinal, and torsional frequencies of concrete specimens. ASTM C215. West Conshohocken, PA: ASTM.
ASTM. 2014b. Standard test method for static modulus and Poisson’s ratio of concrete in compression. ASTM C469/C469M. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39/C39M. West Conshohocken, PA: ASTM.
Calvo, J., D. Revuelta, P. Carballosa, and J. Gutiérrez. 2017. “Comparison between the performance of expansive SCC and expansive conventional concretes in different expansion and curing conditions.” Constr. Build. Mater. 136 (Apr): 277–285. https://doi.org/10.1016/j.conbuildmat.2017.01.039.
Carballosa, P., J. L. Calvo, D. Revuelta, J. J. Sánchez, and J. P. Guriérrez. 2015. “Influence of cement and expansive additive types in the performance of self-compacting concretes for structural elements.” Constr. Build. Mater. 93 (Sep): 223–229. https://doi.org/10.1016/j.conbuildmat.2015.05.113.
CEN (European Committee for Standardization). 1994. Eurocode: Design of composite steel and concrete structures—Part1-1: General rules and rules for building. EN 1994-1-1. Brussels, Belgium: CEN.
Chen, X., and J. Zhou. 2013. “Influence of porosity on compressive and tensile strength of cement mortar.” Constr. Build. Mater. 40 (Mar): 869–874. https://doi.org/10.1016/j.conbuildmat.2012.11.072.
Collepardi, M., A. Borsoi, S. Collepardi, J. Olagot, and R. Troli. 2005. “Effects of shrinkage reducing admixture in shrinkage compensating concrete under non-wet curing conditions.” Cem. Concr. Compos. 27 (6): 704–708. https://doi.org/10.1016/j.cemconcomp.2004.09.020.
Dilli, M., H. Athan, and C. Sengul. 2015. “A comparison of strength and elastic properties between conventional and lightweight structural concretes designed with expanded clay aggregates.” Constr. Build. Mater. 101 (Dec): 260–267. https://doi.org/10.1016/j.conbuildmat.2015.10.080.
Ding, F., J. Liu, X. Liu, Z. Yu, and D. Li. 2015. “Mechanical behavior of circular and square concrete filled steel tube stub columns under local compression.” Thin Walled Struct. 94 (Sep): 155–166. https://doi.org/10.1016/j.tws.2015.04.020.
Du, L., and K. J. Folliard. 2005. “Mechanisms of air entrainment in concrete.” Cem. Concr. Res. 35 (8): 1463–1471. https://doi.org/10.1016/j.cemconres.2004.07.026.
Ekmekyapar, T., and B. J. Al-Eliwi. 2016. “Experimental behavior of circular concrete filled steel tube columns and design specifications.” J. Constr. Steel Res. 105 (Aug): 220–230. https://doi.org/10.1016/j.tws.2016.04.004.
Ghannam, S., Y. A. Jawad, and Y. Hunayti. 2004. “Failure of lightweight aggregate concrete-filled steel tubular columns.” Steel Compos. Struct. 4 (1): 1–8. https://doi.org/10.12989/scs.2004.4.1.001.
Han, J., D. Jia, and P. Yan. 2016a. “Understanding the shrinkage compensating ability of type k expansive agent in concrete.” Constr. Build. Mater. 116 (Jul): 36–44. https://doi.org/10.1016/j.conbuildmat.2016.04.092.
Han, L., Z. Tao, and W. Liu. 2004. “Effects of sustained load on concrete-filled hollow structural steel columns.” J. Struct. Eng. 130 (9): 1392–1404. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:9(1392).
Han, L., Y. Ye, and F. Liao. 2016b. “Effects of core concrete initial imperfection on performance of eccentrically loaded CFST columns.” J. Struct. Eng. 142 (12): 04016132. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001604.
Haque, M. N., H. Al-Khaiat, and O. Kayali. 2004. “Strength and durability of lightweight concrete.” Cem. Concr. Compos. 26 (4): 307–314. https://doi.org/10.1016/S0958-9465(02)00141-5.
Hatzigeorgiou, G. D., and D. E. Beskos. 2005. “Minimum cost design of fibre-reinforced concrete-filled steel tubular columns.” J. Constr. Steel Res. 61 (2): 167–182. https://doi.org/10.1016/j.jcsr.2004.06.003.
Hu, H., C. Huang, and M. Wu. 2003. “Nonlinear analysis of axially loaded concrete-filled tube columns with confinement effect.” J. Struct. Eng. 129 (10): 1322–1329. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:10(1322).
Ji, B., Z. Fu, T. Qu, and M. Wang. 2013. “Stability behavior of lightweight aggregate concrete filled steel tubular columns under axial compression.” Adv. Steel Constr. 9 (1): 1–13. https://doi.org/10.18057/IJASC.2013.9.1.1.
Johansson, M. 2002. “The efficiency of passive confinement in CFT columns.” Steel Compos. Struct. 2 (5): 379–396. https://doi.org/10.12989/scs.2002.2.5.379.
Johansson, M., and K. Gylltoft. 2002. “Mechanical behavior of circular steel-concrete composite stub columns.” J. Struct. Eng. 128 (8): 1073–1081. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:8(1073).
Kai-Cheng, X., C. Meng-Cheng, and Y. Fang. 2011. “Confined expansion and bond property of micro-expansive concrete-filled steel tube columns.” Open Civ. Eng. J. 5 (1): 173–178. https://doi.org/10.2174/1874149501105010173.
Liew, J. Y., and D. X. Xiong. 2012. “Ultra-high strength concrete filled composite columns for multi-storey building construction.” Adv. Struct. Eng. 15 (9): 1487–1503. https://doi.org/10.1260/1369-4332.15.9.1487.
Liew, J. Y., M. Xiong, and D. Xiong. 2016. “Design of concrete-filled tubular beam-columns with high strength steel and concrete.” Structures. 8 (Nov): 213–226. https://doi.org/10.1016/j.istruc.2016.05.005.
Liew, J. Y., M. X. Xiong, and D. X. Xiong. 2017. “Design of high strength concrete filled tubular columns for tall buildings.” J. High-Rise Build. 1 (2-3): 1869–1878. https://doi.org/10.1002/cepa.231.
Mather, B. 1973. “Discussion of the paper: ‘Mechanism of expansion associated ettringite formation’.” Cem. Concr. Res. 3 (5): 651–652. https://doi.org/10.1016/0008-8846(73)90103-8.
Mehta, P., and P. J. Monteiro. 2014. Concrete: Microstructure, properties and materials. 2nd ed. São Paulo, Brazil: Instituto dos Auditores Independentes do Brasil.
Mendes, J. C., T. K. Moro, A. S. Figueiredo, K. D. do Carmo Silva, G. C. Silva, G. J. Silva, and R. A. Peixoto. 2017. “Mechanical, rheological and morphological analysis of cement-based composites with a new LAS-based air entraining agent.” Constr. Build. Mater. 145 (Aug): 648–661. https://doi.org/10.1016/j.conbuildmat.2017.04.024.
Mirmomeni, M., A. Heidarpour, X. Zhao, and R. Al-Mahaidi. 2017. “Size-dependency of concrete-filled steel tubes subject to impact loading.” Int. J. Impact Eng. 100 (Feb): 90–101. https://doi.org/10.1016/j.ijimpeng.2016.11.003.
Mouli, M., and H. Khelafi. 2007. “Strength of short composite rectangular hollow section columns filled with lightweight aggregate concrete.” Eng. Struct. 29 (8): 1791–1797. https://doi.org/10.1016/j.engstruct.2006.10.003.
Oliveira, W. A., S. De Nardin, and A. C. El Debs. 2009. “Composite circular concrete-filled columns design subjected to simple compression, according to NBR 8800:2008 and Eurocode 4:2004: Comparison with experimental results.” Revista Escola de Minas. 62 (1): 73–85. https://doi.org/10.1590/S0370-44672009000100011.
Ouyang, X., Y. Guo, and X. Qiu. 2008. “The feasibility of synthetic surfactant as an air entraining agent for the cement matrix.” Constr. Build. Mater. 22 (8): 1774–1779. https://doi.org/10.1016/j.conbuildmat.2007.05.002.
Qu, X., Z. Chen, D. Nethercot, L. Gardner, and M. Theofanous. 2015. “Push-out tests and bond strength of rectangular CFST columns.” Steel Compos. Struct. 19 (1): 21–41. https://doi.org/10.12989/scs.2015.19.1.021.
Ramachandran, V. 1995. Concrete admixtures handbook. 2nd ed. Saddle River, NJ: Noyes Publications.
Rodrigues, B. H. 2016. Study of steel-concrete adhesion of conventional, lightweight and air-entrained concretes in composite tubular columns. Ouro Preto, Brazil: Universidade Federal de Ouro Preto.
Roeder, C. W., B. Cameron, and C. B. Brown. 1999. “Composite action in concrete filled tubes.” J. Struct. Eng. 125 (5): 477–484. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:5(477).
SAE (Society of Automotive Engineers). 1992. Estimated mechanical properties and machinability of steel bars. J1397. Warrendale, PA: SAE.
SAE (Society of Automotive Engineers). 2012. Carbon Steel, Sheet, Strip, and Plate, (SAE 1020 and 1025). AMS5046D. Warrendale, PA: SAE.
Sakino, K., H. Nakahara, S. Morino, and A. Nishiyama. 2004. “Behavior of centrally load concrete-filled steel tube short columns.” J. Struct. Eng. 130 (2): 180–188. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:2(180).
Schaumann, E., T. Vallee, and T. Keller. 2009. “Modeling of direct load transmission in lightweight-concrete-core sandwich beams.” ACI Struct. J. 106 (4): 435–444.
Shanmugam, N. E., and B. Lakshmi. 2001. “State of the art report on steel-concrete composites columns.” J. Constr. Steel Res. 57 (10): 1041–1080. https://doi.org/10.1016/S0143-974X(01)00021-9.
Soares, A. F. 2009. Specialized software for mix design of cement-based composites. Belo Horizonte, Brazil: Centro Federal de Educação Tecnológica de Minas Gerais.
Susantha, K. A., H. B. Ge, and T. A. Usami. 2001. “Capacity prediction procedure for concrete filled steel columns.” J. Earthquake Eng. 5 (4): 483–520. https://doi.org/10.1080/13632460109350403.
Tam, V., Z. Wang, and Z. Tao. 2014. “Behaviour of recycled aggregate concrete filled stainless steel stub columns.” Mater. Struct. 47 (1–2): 293–310. https://doi.org/10.1617/s11527-013-0061-1.
Tao, Z., T. Song, B. Uy, and L. Han. 2016. “Bond behavior in concrete-filled steel tubes.” J. Constr. Steel Res. 120 (Apr): 81–93. https://doi.org/10.1016/j.jcsr.2015.12.030.
Torres, A. F., and C. E. Rosman. 1956. Method for rational concrete mix design. São Paulo, Brazil: Brazilian Portland Cement Association.
Virdi, K. S., and P. J. Dowling. 1980. “Bond strength in concrete filled steel tubes.” Int. Assoc. Bridge Struct. Eng. 3 (Aug): 125–137.
Xu, C., H. Chengkui, J. Decheng, and S. Yuancheng. 2009. “Push-out test of pre-stressing concrete filled circular steel tube columns by means of expansive cement.” Constr. Build. Mater. 23 (1): 491–497. https://doi.org/10.1016/j.conbuildmat.2007.10.021.
Yu, X., Z. Tao, and T. Song. 2016. “Effect of different types of aggregates on the performance of concrete-filled steel tubular stub columns.” Mater. Struct. 49 (9): 3591–3605. https://doi.org/10.1617/s11527-015-0742-z.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Oct 18, 2018
Accepted: Oct 2, 2019
Published online: Mar 20, 2020
Published in print: Jun 1, 2020
Discussion open until: Aug 20, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.