Effect of Different Humidity-Controlling Modes on Microstructure and Compressive Behavior of Ordinary Concrete
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 1
Abstract
Concretes at different saturation degrees are needed to be prepared in the laboratory when studying the effects of humidity on its mechanical properties. Different humidity control methods would produce different results. The present work investigates the changes in compressive behavior and microstructure of the ordinary concrete caused by two different humidity-controlling modes: (1) the isothermal drying humidity-controlling mode and (2) the rewetting humidity-controlling mode. The compressive behaviors of concrete in different humidity states are compared, and the microstructure is studied in detail using scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). The results indicate that drying results in an increase of compressive strength, whereas rewetting results in a significant decrease. Both drying and rewetting humidity-controlling modes cause some changes in the microstructure of concrete. Drying results in calcium silicate hydrate (C-S-H) globule densification and makes cement matrix denser, increases porosity, and coarsens the pore size distribution. Rewetting makes porosity decrease and the pore size distribution slightly refined, as well as causes serious microcracking. The differences in compressive behavior of concrete is related to the shrinkage or swelling, the change of pore size distribution, and the microcracking caused by two different humidity-controlling modes. The isothermal drying humidity-controlling mode is suggested as the more reasonable mode for concrete because it is more effective in controlling saturation degree, takes less experiment time, and causes less effect on microstructure and the compressive strength of concrete.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support of National Natural Science Foundation of China (No. 51379178) and National Key Research and Development (R&D) Plan of China (No. 2017YFC405101-2).
References
Bartlett, F. M., and J. G. MacGregor. 1994. “Effect of moisture condition on concrete core strengths.” ACI Mater. J. 91 (3): 227–236.
Bazǎnt, Z. P., and W. J. Raftshol. 1982. “Effect of cracking in drying and shrinkage specimens.” Cem. Concr. Res. 12 (2): 209–226.
Cadoni, E., K. Labibes, C. Albertini, M. Berra, and M. Giangrasso. 2001. “Strain-rate effect of the tensile behavior of concrete at different relative humidity levels.” Mater. Struct. 34 (1): 21–26. https://doi.org/10.1007/BF02482196.
Chen, X., S. Wu, and J. Zhou. 2013. “Experimental and modeling study of dynamic mechanical properties of cement paste, mortar and concrete.” Constr. Build. Mater. 47 (Oct): 419–430. https://doi.org/10.1016/j.conbuildmat.2013.05.063.
Feldman, R. F., and J. J. Beaudoin. 1991. “Pretreatment of hydrated cement paste for mercury intrusion measurements.” Cem. Concr. Res. 21 (2): 297–308. https://doi.org/10.1016/0008-8846(91)90011-6.
Feldman, R. F., and P. J. Sereda. 1970. “A new model for hydrated portland cement and its practical implications.” Eng. J. 53 (8–9): 53–59.
Fischer, N., R. Haerdtl, and P. J. McDonald. 2015. “Observation of the redistribution of nanoscale water filled porosity in cement based materials during wetting.” Cem. Concr. Res. 68 (Feb): 148–155. https://doi.org/10.1016/j.cemconres.2014.10.013.
Gallé, C. 2001. “Effect of drying on cement-based materials pore structure as identified by mercury intrusion porosimetry—A comparative study between oven-, vacuum-, and freeze-drying.” Cem. Concr. Res. 31 (10): 1467–1477.
GB (Chinese Standard). 2006. Test code for hydraulic concrete. SL 352. Beijing: People’s Republic of China.
Han, J., Z. Li, H. Liu, G. Zhang, C. Tan, and J. Han. 2018. “Study on the process of isothermal continuous dry and its effect on the strength of concrete of different strength grades.” Constr. Build. Mater. 187 (Oct): 14–24. https://doi.org/10.1016/j.conbuildmat.2018.07.167.
Hotta, H., and K. Takiguchi. 1995. “Influence of drying and water supplying after drying on tensile strength of cement mortar.” Nucl. Eng. Des. 156 (1–2): 219–228. https://doi.org/10.1016/0029-5493(94)00948-X.
Jennings, H. M. 2008. “Refinements to colloid model of C-S-H in cement: CM-II.” Cem. Concr. Res. 38 (3): 275–289. https://doi.org/10.1016/j.cemconres.2007.10.006.
Jin, L., X. Du, and G. Ma. 2012. “Macroscopic effective moduli and tensile strength of saturated concrete.” Cem. Concr. Res. 42 (12): 1590–1600. https://doi.org/10.1016/j.cemconres.2012.09.012.
Kanna, V., R. A. Olson, and H. M. Jennings. 1998. “Effect of shrinkage and moisture content on the physical characteristics of blended cement mortars.” Cem. Concr. Res. 28 (10): 1467–1477. https://doi.org/10.1016/S0008-8846(98)00120-3.
Konecny, L., and S. J. Naqvi. 1993. “The effect of different drying techniques on the pore size distribution of blended cement mortars.” Cem. Concr. Res. 23 (5): 1223–1228. https://doi.org/10.1016/0008-8846(93)90183-A.
Korpa, A., and R. Trettin. 2006. “The influence of different drying methods on cement paste microstructures as reflected by gas adsorption: Comparison between freeze-drying (F-drying), D-drying, P-drying and oven-drying methods.” Cem. Concr. Res. 36 (4): 634–649. https://doi.org/10.1016/j.cemconres.2005.11.021.
Li, G. 2004. The effect of moisture content on the tensile strength properties of concrete. Gainesville, FL: Univ. of Florida.
Li, S. 2014. Preliminary studies on the effect of water content and pore water pressure on the concrete strength. Yangling, China: Northwest A&F Univ.
Liu, B., P. Li, L. Li, and Y. Kang. 2011. “Experimental study on influence of water content on concrete strength.” [In Chinese.] J. Beijing Jiaotong Univ. 35 (1): 9–12.
Liu, B., W. Lv, L. Li, and P. Li. 2014. “Effect of moisture content on static compressive elasticity modulus of concrete.” Constr. Build. Mater. 69 (Oct): 133–142. https://doi.org/10.1016/j.conbuildmat.2014.06.094.
Martys, N. S., and C. F. Ferraris. 1997. “Capillary transport in mortars and concrete.” Cem. Concr. Res. 27 (5): 747–760. https://doi.org/10.1016/S0008-8846(97)00052-5.
Maruyama, I., Y. Nishioka, and G. Igarashi. 2014a. “Microstructural and bulk property changes in hardened cement paste during the first drying process.” Cem. Concr. Res. 58 (Apr): 20–34. https://doi.org/10.1016/j.cemconres.2014.01.007.
Maruyama, I., H. Sasano, Y. Nishioka, and G. Igarashi. 2014b. “Strength and Young’s modulus change in concrete due to long-term drying and heating up to 90°C.” Cem. Concr. Res. 66 (Dec): 48–63. https://doi.org/10.1016/j.cemconres.2014.07.016.
Matsushita, H., and K. Onoue. 2006. “Influence of surface energy on compressive strength of concrete under static and dynamic loading.” J. Adv. Concr. Technol. 4 (3): 409–421. https://doi.org/10.3151/jact.4.409.
Mehta, P. K., and P. J. M. Monteiro. 2006. Concrete: Structure, properties and materials. New York: Prentice-Hall.
Moukwa, M., and P. C. Aītcin. 1988. “The effect of drying on cement pastes pore structure as determined by mercury porosimetry.” Cem. Concr. Res. 18 (5): 745–752. https://doi.org/10.1016/0008-8846(88)90098-1.
Olson, R. A., and H. M. Jennings. 2001. “Estimation of C-S-H content in a blended cement paste using water adsorption.” Cem. Concr. Res. 31 (3): 351–356. https://doi.org/10.1016/S0008-8846(01)00454-9.
Parrott, L. J. 1981. “Effect of drying history upon the exchange of pore water with methanol and upon subsequent methanol sorption behaviour in hydrated alite paste.” Cem. Concr. Res. 11 (5): 651–658. https://doi.org/10.1016/0008-8846(81)90023-5.
Parrott, L. J., W. Hansen, and R. L. Berger. 1980. “Effect of first drying upon the pore structure of hydrated alite paste.” Cem. Concr. Res. 10 (5): 647–655. https://doi.org/10.1016/0008-8846(80)90028-9.
Piasta, J. 1984. “Heat deformations of cement paste phases and the microstructure of cement paste.” Mater. Struct. 17 (6): 415–420. https://doi.org/10.1007/BF02473981.
Ross, C. A., D. M. Jerome, J. W. Tedesco, and M. L. Hughes. 1996. “Moisture and strain rate effects on concrete strength.” ACI Mater. J. 93 (3): 293–298.
Ross, C. A., J. W. Tedesco, and S. T. Kuennen. 1995. “Effects of strain rate on concrete strength.” ACI Mater. J. 92 (1): 37–47.
Rossi, P., and F. Foutlemonde. 1996. “Effect of loading rate on the tensile behavior of concrete: Description of the physical mechanisms.” Mater. Struct. 29 (2): 116–118. https://doi.org/10.1007/BF02486201.
Sabir, B. B., S. Wild, and M. O’Farrell. 1998. “A water sorptivity test for mortar and concrete.” Mater. Struct. 31 (8): 568–574. https://doi.org/10.1007/BF02481540.
Skoczylas, F., N. Burlion, and I. Yurtdas. 2007. “About drying effects and poro-mechanical behaviour of mortars.” Cem. Concr. Res. 29 (5): 383–390. https://doi.org/10.1016/j.cemconcomp.2006.11.008.
Snoeck, D., L. F. Velasco, A. Mignon, S. Van Vlierberghe, P. Dubruelb, P. Lodewyckx, and N. De Belie. 2014. “The influence of different drying techniques on the water sorption properties of cement-based materials.” Cem. Concr. Res. 64 (10): 54–62. https://doi.org/10.1016/j.cemconres.2014.06.009.
Szczesniak, M., T. Rougelot, N. Burlion, and J. Shao. 2013. “Compressive strength of cement-based composites—Roles of aggregate diameter and water saturation degree.” Cem. Concr. Res. 37 (4): 249–258. https://doi.org/10.1016/j.cemconcomp.2012.08.001.
Wang, H., W. Jin, and Q. Li. 2009. “Saturation effect on dynamic tensile and compressive strength of concrete.” Adv. Struct. Eng. 12 (2): 279–286. https://doi.org/10.1260/136943309788251713.
Wang, H., and Q. Li. 2007a. “Experiments of the compressive properties of dry and saturated concrete under different loading rates.” [In Chinese.] J. Hydraul. Eng. 26 (1): 84–89.
Wang, H., and Q. Li. 2007b. “Prediction of elastic modulus and Poisson’s ratio for unsaturated concrete.” Int. J. Solids Struct. 44 (5): 1370–1379. https://doi.org/10.1016/j.ijsolstr.2006.06.028.
Wang, H., L. Wang, Y. Song, and J. Wang. 2016. “Influence of free water on dynamic behavior of dam concrete under biaxial compression.” Constr. Build. Mater. 112 (Jun): 222–231. https://doi.org/10.1016/j.conbuildmat.2016.02.090.
Wittmann, F. H. 1968. “Surface tension skrinkage and strength of hardened cement paste.” Matériaux Constr. 1 (6): 547–552. https://doi.org/10.1007/BF02473643.
Wittmann, F. H. 2010. “Interaction of hardened cement paste and water.” J. Am. Ceram. Soc. 56 (8): 409–415. https://doi.org/10.1111/j.1151-2916.1973.tb12711.x.
Wittmann, F. H., P. E. Roelfstra, and C. L. Kamp. 1988. “Drying of concrete: An application of the 3L-approach.” Nucl. Eng. Des. 105 (2): 185–198. https://doi.org/10.1016/0029-5493(88)90339-1.
Zhang, G., Z. Li, L. Zhang, Y. Shang, and H. Wang. 2017. “Experimental research on drying control condition with minimal effect on concrete strength.” Constr. Build. Mater. 135 (Mar): 194–202. https://doi.org/10.1016/j.conbuildmat.2016.12.141.
Zhang, J., Y. Gao, Y. Han, and W. Wun. 2012. “Shrinkage and interior humidity of concrete under dry-wet cycles.” Drying Technol. 30 (6): 583–596. https://doi.org/10.1080/07373937.2011.653614.
Zhang, Y. 2014. Study on effect of degree of pore saturation on fly ash concrete mechanical behavior. Xuzhou, China: China Univ. of Mining and Technology.
Zhang, Z., M. Thiery, and V. Baroghel-Bouny. 2016. “Investigation of moisture transport properties of cementitious materials.” Cem. Concr. Res. 89 (Nov): 257–268. https://doi.org/10.1016/j.cemconres.2016.08.013.
Zhou, J., X. Chen, L. Wu, and X. Kan. 2011. “Influence of free water content on the compressive mechanical behaviour of cement mortar under high strain rate.” Sadhana 36 (3): 357–369. https://doi.org/10.1007/s12046-011-0024-6.
Zhou, J., and N. Ding. 2014. “Moisture effect on compressive behavior of concrete under dynamic loading.” J. Cent. S. Univ. 21 (12): 4714–4722. https://doi.org/10.1007/s11771-014-2481-7.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 32 • Issue 1 • January 2020
Copyright
©2019 American Society of Civil Engineers.
History
Received: Dec 11, 2018
Accepted: Jul 3, 2019
Published online: Nov 5, 2019
Published in print: Jan 1, 2020
Discussion open until: Apr 5, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.