Experimental and Statistical Evaluation of Asphalt Binders Produced in Jordan Treated with Different Modifiers
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 2
Abstract
This study evaluated potential improvements in the physical and rheological properties of asphalt binders modified with crumb tire rubber (CTR), microcrystalline synthetic wax (MSW), and nanosilica (NS). Asphalt binder with penetration grade was used. A statistical analysis of the experimental data was performed to determine the effect of using CTR, MSW, and NS on and asphalt binder grades and to detect any differences. Both physical and rheological tests of pure and modified asphalt binders were conducted. The physical tests were the penetration test, softening point test, and flash and fire points test, whereas the rheological tests included the rotational viscometer (RV) test, dynamic shear rheometer (DSR) test, and bending beam rheometer (BBR) test. The results showed that adding CTR and NS enhanced the high-temperature performance, but it had no effect on low-temperature performance. The results did not indicate enhancement by MSW of high-temperature performance but indicated a negative effect on low-temperature performance. The experimental results were compared and analyzed statistically by ANOVA to find any significant differences between the effect of modifier type, binder grade, and test temperature. Based on the one-way ANOVA results, the modifier type had a significant effect on physical properties and rotational viscosity. The two-way ANOVA results revealed that the change in modifier type and binder grade together had a significant effect on flash point and rutting parameter for unaged samples at 58°C only. The three-way ANOVA indicated that changing the modifier type, binder grade, and test temperature all together had a noticeable effect on the BBR m-value test results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors extend their warm appreciation to the Highway Laboratories at both Jordan University of Science and Technology and Yarmouk University, where experiments were conducted. In addition, the authors are extremely thankful for the help provided by all technicians at these two universities.
References
AASHTO. 2007. Standard practice for determination of low-temperature performance grade (PG) of asphalt binders. ASHTO PP42. Washington, DC: AASHTO.
AASHTO. 2012a. Standard method of test for determining the flexural creep stiffness of asphalt binder using the bending beam rheometer (BBR). AASHTO T313. Washington, DC: AASHTO.
AASHTO. 2012b. Standard method of test for viscosity determination the rheological properties of asphalt binder using a dynamic shear rheometer. AASHTO T315-10. Washington, DC: AASHTO.
AASHTO. 2013. Standard method of test for viscosity determination of asphalt binder using rotational viscometer. AASHTO T316. Washington, DC: AASHTO.
AASHTO. 2015. Standard method of test for flash and fire points by Cleveland open cup. AASHTO T48. Washington, DC: AASHTO.
AASHTO. 2017. Standard specification for performance-graded asphalt binder. AASHTO M320. Washington, DC: AASHTO.
Airey, G. D., M. M. Rahman, and A. C. Collop. 2003. “Absorption of bitumen into crumb rubber using the basket drainage method.” Int. J. Pavement Eng. 4 (2): 105–119. https://doi.org/10.1080/1029843032000158879.
Alhamali, D. I., J. Wu, Q. Liu, N. A. Hassan, N. I. M. Yusoff, and S. I. A. Ali. 2016. “Physical and rheological characteristics of polymer modified bitumen with nanosilica particles.” Arabian J. Sci. Eng. 41 (4): 1521–1530. https://doi.org/10.1007/s13369-015-1964-7.
Al-Khateeb, G. G., and K. Z. Ramadan. 2015. “Investigation of the effect of rubber on rheological properties of asphalt binders using superpave DSR.” KSCE J. Civ. Eng. 19 (1): 127–135. https://doi.org/10.1007/s12205-012-0629-2.
Al-Omari, A., M. Taamneh, M. A. Khasawneh, and A. Al-Hosainat. 2018. “Effect of crumb tire rubber, microcrystalline synthetic wax, and nano silica on asphalt rheology.” Road Mater. Pavement Des. https://doi.org/10.1080/14680629.2018.1527718.
ASTM. 1997. Standard test method for penetration of bituminous materials. ASTM D5. West Conshohocken, PA: ASTM.
ASTM. 2006. Standard test method for softening point of bitumen (ring-and-ball apparatus). ASTM D36. West Conshohocken, PA: ASTM.
ASTM. 2007. Standard test method for ductility of bituminous materials. ASTM D113. West Conshohocken, PA: ASTM.
ASTM. 2009. Standard test method for density of semi-solid bituminous materials (pycnometer method). ASTM D70. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test method for flash and fire points by Cleveland open cup tester. ASTM D92. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for viscosity determination of asphalt at elevated temperatures using a rotational viscometer. ASTM D4402/D4402M. West Conshohocken, PA: ASTM.
Behnood, A., and J. Olek. 2017. “Rheological properties of asphalt binders modified with styrene-butadiene-styrene (SBS), ground tire rubber (GTR), or polyphosphoric acid (PPA).” Constr. Build. Mater. 151 (Oct): 464–478. https://doi.org/10.1016/j.conbuildmat.2017.06.115.
Canestrari, F., A. Graziani, V. Pannunzio, and H. U. Bahia. 2013. “Rheological properties of bituminous binders with synthetic wax.” Int. J. Pavement Res. Technol. 6 (1): 15–21.
Cong, P., P. Xun, M. Xing, and S. Chen. 2013. “Investigation of asphalt binder containing various crumb rubbers and asphalts.” Constr. Build. Mater. 40 (Mar): 632–641. https://doi.org/10.1016/j.conbuildmat.2012.11.063.
Edwards, Y. 2009. “Influence of waxes on bitumen and asphalt concrete mixture performance.” Road Mater. Pavement Des. 10 (2): 313–335. https://doi.org/10.1080/14680629.2009.9690197.
Enieb, M., and A. Diab. 2017. “Characteristics of asphalt binder and mixture containing nanosilica.” Int. J. Pavement Res. Technol. 10 (2): 148–157. https://doi.org/10.1016/j.ijprt.2016.11.009.
Ezzat, H., S. El-Badawy, A. Gabr, E. S. I. Zaki, and T. Breakah. 2016. “Evaluation of asphalt binders modified with nanoclay and nanosilica.” Procedia Eng. 143 (Jan): 1260–1267. https://doi.org/10.1016/j.proeng.2016.06.119.
Fini, E. H., P. Hajikarimi, M. Rahi, and F. MoghadasNejad. 2015. “Physiochemical, rheological, and oxidative aging characteristics of asphalt binder in the presence of mesoporous silica nanoparticles.” J. Mater. Civ. Eng. 28 (2): 04015133. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001423.
Gergo, P., A. Hollo, and A. Geiger. 2017. “Rheological investigation of rubber Bitumen containing various waxes as warm mix additive.” Stud. Universitatis Babes-Bolyai, Chemia 62 (2): 247–257. https://doi.org/10.24193/subbchem.2017.2.19.
Ghuzlan, K. A., and M. O. Al Assi. 2017. “Sasobit-modified asphalt binder rheology.” J. Mater. Civ. Eng. 29 (9): 04017142. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001996.
Golchin, B., M. O. Hamzah, S. R. Omranian, and M. R. M. Hasan. 2018. “Effects of a surfactant-wax based warm additive on high temperature rheological properties of asphalt binders.” Constr. Build. Mater. 183 (Sep): 395–407. https://doi.org/10.1016/j.conbuildmat.2018.06.099.
Goli, A., H. Ziari, and A. Amini. 2016. “Evaluating the performance of crumb rubber modified binders used in Isfahan Province.” Int. J. Transp. Eng. 4 (2): 97–107.
Hajikarimi, P., M. Rahi, and F. MoghadasNejad. 2015. “Comparing different rutting specification parameters using high temperature characteristics of rubber-modified asphalt binders.” Road Mater. Pavement Des. 16 (4): 751–766. https://doi.org/10.1080/14680629.2015.1063533.
Han, L., M. Zheng, J. Li, Y. Li, Y. Zhu, and Q. Ma. 2017. “Effect of nano silica and pretreated rubber on the properties of terminal blend crumb rubber modified asphalt.” Constr. Build. Mater. 157 (Dec): 277–291. https://doi.org/10.1016/j.conbuildmat.2017.08.187.
Hasaninia, M., and F. Haddadi. 2018. “Studying engineering characteristics of asphalt binder and mixture modified by nanosilica and estimating their correlations.” Adv. Mater. Sci. Eng. 2018: 9. https://doi.org/10.1155/2018/4560101.
Huang, S. C. 2008. “Rubber concentrations on rheology of aged asphalt binders.” J. Mater. Civ. Eng. 20 (3): 221–229. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:3(221).
Irfan, M., Y. Ali, S. Ahmed, and I. Hafeez. 2018. “Performance evaluation of crumb rubber-modified asphalt mixtures based on laboratory and field investigations.” Arabian J. Sci. Eng. 43 (4): 1795–1806. https://doi.org/10.1007/s13369-017-2729-2.
Iwanski, M., and G. Mazurek. 2012. “Rheological characteristics of synthetic wax-modified asphalt binders.” Polimery 57 (9): 661–664. https://doi.org/10.14314/polimery.2012.661.
Kim, H. H., K. D. Jeong, M. S. Lee, and S. J. Lee. 2015. “Effect of FT paraffin wax contents on performance properties of crumb rubber–modified asphalt binders.” J. Mater. Civ. Eng. 27 (11): 04015011. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001267.
Lee, H. N., and W. G. Wong. 2009. “Effect of wax on basic and rheological properties of bitumen with similar Penetration-grades.” Constr. Build. Mater. 23 (1): 507–514. https://doi.org/10.1016/j.conbuildmat.2007.10.020.
Lee, S. J., C. K. Akisetty, and S. N. Amirkhanian. 2008. “The effect of crumb rubber modifier (CRM) on the performance properties of rubberized binders in HMA pavements.” Constr. Build. Mater. 22 (7): 1368–1376. https://doi.org/10.1016/j.conbuildmat.2007.04.010.
Leng, Z., H. Yu, Z. Zhang, and Z. Tan. 2017. “Optimizing the mixing procedure of warm asphalt rubber with wax-based additives through mechanism investigation and performance characterization.” Constr. Build. Mater. 144 (Jul): 291–299. https://doi.org/10.1016/j.conbuildmat.2017.03.208.
Mashaan, N. S., and M. R. Karim. 2013. “Investigating the rheological properties of crumb rubber modified bitumen and its correlation with temperature susceptibility.” Mater. Res. 16 (1): 116–127. https://doi.org/10.1590/S1516-14392012005000166.
Mokhtari, A., H. Behbahani, and A. R. Ghortekolai. 2011. “Effect of commercial wax and typical additives on moisture susceptibility of SMA mixtures.” J. Appl. Sci. 11 (22): 3708–3716. https://doi.org/10.3923/jas.2011.3708.3716.
Msallam, M., and I. Asi. 2018. “Improvement of local asphalt concrete binders using crumb rubber.” J. Mater. Civ. Eng. 30 (4): 04018048. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002238.
Nejad, F. M., H. Nazari, K. Naderi, F. KarimiyanKhosroshahi, and M. HatefiOskuei. 2017. “Thermal and rheological properties of nanoparticle modified asphalt binder at low and intermediate temperature range;” Pet. Sci. Technol. 35 (7): 641–646. https://doi.org/10.1080/10916466.2016.1276589.
Oner, J., B. Sengoz, N. Maidanova, A. Topal, and G. Malkoc. 2016. “Evaluation of rheological effects of waxes on bitumen from different sources.” In Proc., 6th Eurasphalt and Eurobitumen Congress. Ermelo, Netherlands: Stichting Eurasphalt.
Ray, S. S., and M. Okamoto. 2003. “Polymer/layered silicate nanocomposites: A review from preparation to processing.” Prog. Polym. Sci. 28 (11): 1539–1641. https://doi.org/10.1016/j.progpolymsci.2003.08.002.
Roberts, F. L., P. S. Kandhal, E. R. Brown, D. Y. Lee, and T. W. Kennedy. 1996. Hot mix asphalt materials, mixture design, and construction. Lanham, MD: National Asphalt Pavement Association Education Foundation.
Sadeghpour Galooyak, S., M. Palassi, A. Goli, and H. Zanjirani Farahani. 2015. “Performance evaluation of nano-silica modified bitumen.” Int. J. Transp. Eng. 3 (1): 55–66.
Seltman, H. J. 2012. Experimental design and analysis. Newbury Park, CA: SAGE.
Simnofske, D., and K. Mollenhauer. 2017. “Effect of wax crystallization on complex modulus of modified bitumen after varied temperature conditioning rates.” IOP Conf. Series: Mater. Sci. Eng. 236 (1): 012003. https://doi.org/10.1088/1757-899X/236/1/012003.
Singh, D., P. K. Ashish, and A. Jagadeesh. 2018. “Influence of particle and interaction effects of different sizes of crumb rubber on rheological performance parameters of binders.” J. Mater. Civ. Eng. 30 (5): 04018066. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002245.
Tan, Y., L. Zhang, W. Gong, and M. Guo. 2012. “Investigation of the effects of wax additive on the properties of asphalt binder.” Constr. Build. Mater. 36 (Nov): 578–584. https://doi.org/10.1016/j.conbuildmat.2012.06.024.
Tasdemir, Y. 2009. “High temperature properties of wax modified binders and asphalt mixtures.” Constr. Build. Mater. 23 (10): 3220–3224. https://doi.org/10.1016/j.conbuildmat.2009.06.010.
Wulandari, P. S., and D. Tjandra. 2017. “Use of crumb rubber as an additive in asphalt concrete mixture.” Procedia Eng. 171: 1384–1389. https://doi.org/10.1016/j.proeng.2017.01.451.
Xiang, L., J. Cheng, and G. Que. 2009. “Microstructure and performance of crumb rubber modified asphalt.” Constr. Build. Mater. 23 (12): 3586–3590. https://doi.org/10.1016/j.conbuildmat.2009.06.038.
Yaacob, H., M. Ali Mughal, R. P. Jaya, M. R. Hainin, D. S. Jayanti, and C. N. Che Wan. 2016. “Rheological properties of styrene butadiene rubber modified bitumen binder.” J. Teknologi 78 (2–7): 121–126.
Yang, S., K. Yan, W. He, and H. Wang. 2017. “Laboratory evaluation of Deurex-modified asphalt.” J. Mater. Civ. Eng. 30 (1): 04017258. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002111.
Yao, H., Z. You, L. Li, C. H. Lee, D. Wingard, Y. K. Yap, and S. W. Goh. 2012. “Rheological properties and chemical bonding of asphalt modified with nanosilica.” J. Mater. Civ. Eng. 25 (11): 1619–1630. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000690.
Zafari, F., M. Rahi, N. Moshtagh, and H. Nazockdast. 2014. “The improvement of bitumen properties by adding nanosilica.” Study Civ. Eng. Archit. 3 (Dec): 62–69.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 4, 2019
Accepted: Jul 1, 2019
Published online: Nov 20, 2019
Published in print: Feb 1, 2020
Discussion open until: Apr 20, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.