Development Length and Bond Behavior of Steel Bars in Steel Fiber–Reinforced Concrete in Flexural Test
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 1
Abstract
The bond between concrete and steel bars defines the structural behavior of reinforced concrete—each is the complement of the other. The bond allows for the compatibility of strains, transmission of stresses, and good mechanical behavior, with less possibility of the concrete cracking; this can result in the protection of the reinforcement and a higher structural durability. This study investigates (1) the bond behavior between concrete and steel bars, and (2) the development length of steel bars in steel fiber-reinforced concrete (SFRC). For the tests, the bars had diameters of 8 and 12.5 mm with full development lengths (), and with reductions of 50% () and 25% (). The volume fraction of steel fibers () had values of 0.0%, 0.5%, and 1.5%. In the results, the flexural ultimate loading for SFRC was higher than for nonfiber-reinforced concrete. For samples with a of 1.5%, the bond strength was higher than that found in other concretes, confirming that the use of steel fibers improved the bond between concrete and reinforcement and the effectiveness of the proposed test system.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank the Institute of Ecological Research of the Amazon (Instituto de Pesquisas Ecológicas da Amazônia, IPEAM) for the support of this and other research carried out in the Amazon.
References
ABNT (Associação Brasileira De Normas Técnicas). 2013. Materiais metálicos—Ensaio de Tração. NBR ISO 6892. Rio de Janeiro, Brazil: ABNT.
ABNT (Associação Brasileira De Normas Técnicas). 2014. Projeto de estruturas de concreto—Procedimentos. NBR 6118. Rio de Janeiro, Brazil: ABNT.
ACI (American Concrete Institute). 1988. Design considerations for steel fiber reinforced concrete. ACI 544.4R. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2003. ACI 408R–Bond and Development of straight reinforcing bars in tension. ACI 408R. Farmington Hills, MI: ACI.
Afroughsabet, V., L. Biolzi, and T. Ozbakkaloglu. 2016. “High-performance fiber-reinforced concrete: A review.” J. Mater. Sci. 51 (14): 6517–6551. https://doi.org/10.1007/s10853-016-9917-4.
Alavi-Fard, M., and H. Marzouk. 2004. “Bond of high strength concrete under monotonic pullout loading.” Mag. Concr. Res. 56 (9): 545–557. https://doi.org/10.1680/macr.2004.56.9.545.
Amin, A., M. Watts, and S. J. Foster. 2016. “Modelling the tension stiffening effect in SFR-RC.” Mag. Concr. Res. 68 (7): 339–352. https://doi.org/10.1680/macr.15.00188.
Cairns, J., and L. Feldman. 2018. “Strength of laps and anchorages of plain surface bars.” Struct. Concr. 19 (6): 1782–1791. https://doi.org/10.1002/suco.201700242.
CEB-FIP. 2010. MODEL CODE 2010: Final draft. Lausanne, Switzerland: International Federation for Structural Concrete.
Corinaldesi, V., and G. Moriconi. 2004. “Durable fiber reinforced self-compacting concrete.” Cem. Concr. Res. 34 (2): 249–254. https://doi.org/10.1016/j.cemconres.2003.07.005.
Cunha, V. M. C. F., J. A. O. Barros, and J. M. Sena-Cruz. 2010. “Pullout behavior of steel fibers in self-compacting concrete.” J. Mater. Civ. Eng. 22 (1): 1–9. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000001.
Ferguson, P. M. 1966. “Bond stress–The state of the art.” ACI J. Proc. 63 (11): 1161–1190.
fib (International Federation for Structural Concrete). 2013. Model code for concrete structures 2010. Berlin: Ernst & Sohn.
fib (International Federation for Structural Concrete). 2014. Bond and anchorage of embedded reinforcement: Background to the fib model code 2010. fib Bulletin 72. Lausanne, Switzerland: fib.
Ganesan, N., A. Santhakumar, and P. V. Indira. 2014. “Influence of steel fibres on tension stiffening and cracking of reinforced geopolymer concrete.” Mag. Concr. Res. 66 (6): 268–276. https://doi.org/10.1680/macr.13.00273.
García-Taengua, E., J. R. Martí-Vargas, and P. Serna-Ros. 2011. “Statistical approach to effect of factors involved in bond performance of steel fiber-reinforced concrete.” ACI Struct. J. 108 (4): 461–468.
Harajli, M. H. 2009. “Bond stress-slip model for steel bars in unconfined or steel, FRC, or FRP confined concrete under cycling loading.” J. Struct. Eng. 135 (5): 509–518. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:5(509).
Kazim, T. 2003. “Bond strength of reinforcement in splices in beams.” Struct. Eng. Mech. 16 (4): 469–478. https://doi.org/10.12989/sem.2003.16.4.469.
Metelli, G., J. Cairns, and G. A. Plizzari. 2014a. “The influence of percentage of bars lapped on performance of splices.” Mater. Struct. 48 (9): 2983–2996. https://doi.org/10.1617/s11527-014-0371-y.
Metelli, G., E. Marchina, and G. A. Plizziari. 2017. “Experimental study on staggered lapped bars in fiber reinforced concrete beams.” Compos. Struct. 179 (Nov): 655–664. https://doi.org/10.1016/j.compstruct.2017.07.069.
Metelli, G., and G. A. Plizziari. 2014b. “Influence of the relative rib area on bond behavior.” Mag. Concr. Res. 66 (6): 277–294. https://doi.org/10.1680/macr.13.00198.
Orangun, C. O., J. O. Jirsa, and J. E. Breen. 1977. “A reevaluation of test data on development length and splices.” ACI J. 74 (3): 114–122.
RILEM (Réunion Internationale des Laboratoires et Experts des Matériaux). 1983. “RC6 – Bond test for reinforcement steel. 2. Pull-out test.” In RILEM Recommendations for the Testing and Use of Constructions Materials, 218–220. London: E & FN SPON.
RILEM (Réunion Internationale des Laboratoires et Experts des Matériaux). 2002. “Recommendations of RILEM TC 162-TDF: Test and design methods for steel fibre reinforced concrete: Bending test.” Mater. Struct. 35 (253): 579–582.
Silva, B. V., M. P. Barbosa, L. C. P. D. Silva Filho, and M. S. Lorrain. 2013. “Experimental investigation on the use of steel-concrete bond tests for estimating axial compressive strength of concrete: Part 1.” IBRACON Struct. Mater. J. 6 (5): 715–736. https://doi.org/10.1590/S1983-41952013000500003.
Solomos, G., and M. Berra. 2010. “Rebar pullout testing under dynamic Hopkinson bar induced impulsive loading.” Mater. Struct. 43 (1–2): 247–260. https://doi.org/10.1617/s11527-009-9485-z.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Oct 4, 2018
Accepted: Jun 19, 2019
Published online: Oct 31, 2019
Published in print: Jan 1, 2020
Discussion open until: Mar 31, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.