Recycled Concrete Aggregate Modified with Polyvinyl Alcohol and Fly Ash for Concrete Pavement Applications
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 7
Abstract
Recycled concrete aggregate (RCA) is traditionally limited to nonstructural applications. Although the crushing process results in weak mortar particles and surface cracks throughout the RCA, RCA concrete can be employed as rigid pavement materials after its mechanical strength has been improved. This research evaluated the novel use of polyvinyl alcohol (PVA) and fly ash (FA) for the improvement of mechanical strengths of RCA concrete. The influence of PVA to binder () and FA/cement () ratios on the mechanical strength of RCA-PVA-FA concrete was assessed by compressive, split tensile, and flexural strength tests. The mechanisms controlling the improvement of mechanical strengths were discussed based on the results of microstructural analysis using scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) methods. The results of this research indicate that the addition of PVA resulted in a reduction of the compressive strength of RCA concrete in both the short and the long term. However, with an optimum of 1%, both the flexural and tensile strengths increased significantly. At the optimal , the PVA films infiltrated into cementitious matrixes and enhanced the reinforcing ability within the matrixes. However, excess retarded the hydration process and caused reductions in the cementitious tensile bonding. The long-term mechanical strength () was remarkably improved by FA addition at optimum of 20:80, and the presence of cementitious products on the FA grains and in the voids was clearly observed. The highest long-term flexural and tensile strengths were found at and , whereby the 28-day flexural strength was higher than the requirement specified by the US Army and the US Air Force. The 28-day compressive strengths were also higher than the requirements specified by Department of Highways, Thailand. The outcome of this research will result in the promotion of using wastes, namely RCA and FA, in rigid pavement application, which is practical and preferred from engineering, economic, and environmental perspectives.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work is financially supported by the Thailand Research Fund under the TRF Senior Research Scholar program Grant No. RTA5980005, the Ph.D. Royal Jubilee program Grant No. 0143/2557, and Suranaree University of Technology.
References
Abbass, W., M. I. Khan, and S. Mourad. 2018. “Evaluation of mechanical properties of steel fiber reinforced concrete with different strengths of concrete.” Constr. Build. Mater. 168: 556–569. https://doi.org/10.1016/j.conbuildmat.2018.02.164.
Allahverdi, A., K. Kianpur, and M. Moghbeli. 2010. “Effect of polyvinyl alcohol on flexural strength and some important physical properties of portland cement paste.” Iran. J. Mater. Sci. Eng. 7 (1): 1–6.
Ann, K. Y., H. Y. Moon, Y. B. Kim, and J. Ryou. 2008. “Durability of recycled aggregate concrete using pozzolanic materials.” Waste Manage. 28 (6): 993–999. https://doi.org/10.1016/j.wasman.2007.03.003.
Arulrajah, A., T. A. Kua, C. Suksiripattanapong, and S. Horpibulsuk. 2017. “Stiffness and strength properties of spent coffee grounds-recycled glass geopolymers.” Road Mater. Pavement Des. 20 (3): 623–638. https://doi.org/10.1080/14680629.2017.1408483.
Arulrajah, A., A. Mohammadinia, S. Horpibulsuk, and W. Samingthong. 2016. “Influence of class F fly ash and curing temperature on strength development of fly ash-recycled concrete aggregate blends.” Constr. Build. Mater. 127: 743–750. https://doi.org/10.1016/j.conbuildmat.2016.10.049.
ASTM. 2016a. Standard practice for making and curing concrete test specimens in the laboratory. ASTM C192. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard specification for concrete aggregates. ASTM C33. West Conshohocken, PA: ASTM.
ASTM. 2016c. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39. West Conshohocken, PA: ASTM.
ASTM. 2016d. Standard test method for flexural strength of concrete (using simple beam with center-point loading). ASTM C293. West Conshohocken, PA: ASTM.
ASTM. 2016e. Standard test method for splitting tensile strength of cylindrical concrete specimens. ASTM C496. West Conshohocken, PA: ASTM.
Barnes, P., and J. Bensted. 2002. Structure and performance of cements. Boca Raton, FL: CRC Press.
Behera, M., S. K. Bhattacharyya, A. K. Minocha, R. Deoliya, and S. Maiti. 2014. “Recycled aggregate from C&D waste and its use in concrete—A breakthrough towards sustainability in construction sector: A review.” Constr. Build. Mater. 68: 501–516. https://doi.org/10.1016/j.conbuildmat.2014.07.003.
Berry, E. E., R. T. Hemmings, M. H. Zhang, B. J. Cornelius, and D. M. Golden. 1994. “Hydration in high-volume fly ash concrete binders.” Mater. J. 91 (4): 382–389.
Buck, A. D. 1997. “Recycled concrete as a source of aggregate.” Am. Concr. Inst. J. 74 (5): 212–219.
Chen, H. J., T. Yen, and K. H. Chen. 2003. “Use of building rubbles as recycled aggregates.” Cem. Concr. Res. 33 (1): 125–132. https://doi.org/10.1016/S0008-8846(02)00938-9.
Contrafatto, L. 2013. “Mechanical properties of polyvinyl-alcohol modified concrete.” In Proc., Advanced Materials Research Conf. Catania, Italy: Univ. of Catania.
Donrak, J., S. Horpibulsuk, A. Arulrajah, H. Kao, A. Chinkulkijniwat, and M. Hoy. 2018. “Wetting-drying cycles durability of cement stabilized marginal lateritic soil/melamine debris blends for pavement applications.” Road Mater. Pavement Des. 1–19. https://doi.org/10.1080/14680629.2018.1506816.
Fraay, A. L. A., J. M. Bijen, and Y. M. De Haan. 1989. “The reaction of fly ash in concrete a critical examination.” Cem. Concr. Res. 19 (2): 235–246. https://doi.org/10.1016/0008-8846(89)90088-4.
Garcia-Lodeiro, I., V. Carcelen-Taboada, A. Fernández-Jiménez, and A. Palomo. 2016. “Manufacture of hybrid cements with fly ash and bottom ash from a municipal solid waste incinerator.” Constr. Build. Mater. 105: 218–226. https://doi.org/10.1016/j.conbuildmat.2015.12.079.
Gopinathan, K., and R. Rao. 1992. “Influence of some water soluble polymers on the mechanical properties of cement polymer composites.” In Proc., 9th Int. Congress on Chemistry of Cement (ICCC), 538–543. New Delhi, India.
Hansen, T. C., and E. Boegh. 1985. “Elasticity and drying shrinkage of recycled: Aggregate concrete.” J. Proc. 82 (5): 648–652.
Hansen, T. C., and H. Narud. 1983. “Strength of recycled concrete made from crushed concrete coarse aggregate.” Concr. Int. 5 (01): 79–83.
Hassan, C. M., and N. A. Peppas. 2000a. “Structure and applications of poly (vinyl alcohol) hydrogels produced by conventional crosslinking or by freezing/thawing methods.” In Biopolymers·PVA hydrogels anionic polymerisation nanocomposites, 37–65. Berlin: Springer.
Hassan, C. M., and N. A. Peppas. 2000b. “Structure and morphology of freeze/thawed PVA hydrogels.” Macromolecules 33 (7): 2472–2479. https://doi.org/10.1021/ma9907587.
Hoy, M., S. Horpibulsuk, and A. Arulrajah. 2016. “Strength development of recycled asphalt pavement-fly ash geopolymer as a road pavement material.” Constr. Build. Mater. 117: 209–219. https://doi.org/10.1016/j.conbuildmat.2016.04.136.
Jamsawang, P., P. Voottipruex, and S. Horpibulsuk. 2015. “Flexural strength characteristics of compacted cement-polypropylene fiber sand.” J. Mater. Civ. Eng. 27 (9): 04014243. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001205.
Jaroslav, T., P. Zdenek, I. Katerina, and P. V. Tomáö. 2015. “Effect of PVA modification on the properties of cement composites.” Acta Polytech. 55 (1): 64–75. https://doi.org/10.14311/AP.2015.55.0064.
Jitchaiyaphum, K., T. Sinsiri, C. Jaturapitakkul, and P. Chindaprasirt. 2013. “Cellular lightweight concrete containing high-calcium fly ash and natural zeolite.” Int. J. Min. Metall. Mater. 20 (5): 462–471. https://doi.org/10.1007/s12613-013-0752-1.
Kheder, G. F., and S. A. Al-Windawi. 2005. “Variation in mechanical properties of natural and recycled aggregate concrete as related to the strength of their binding mortar.” Mater. Struct. 38 (7): 701–709. https://doi.org/10.1007/BF02484315.
Kim, J. H., and R. E. Robertson. 1998. “Effects of polyvinyl alcohol on aggregate-paste bond strength and the interfacial transition zone.” Adv. Cem. Based Mater. 8 (2): 66–76. https://doi.org/10.1016/S1065-7355(98)00009-1.
Kim, J. H., R. E. Robertson, and A. E. Naaman. 1999. “Structure and properties of poly(vinyl alcohol)-modified mortar and concrete.” Cem. Concr. Res. 29 (3): 407–415. https://doi.org/10.1016/S0008-8846(98)00246-4.
Kim, Y. Y., K. M. Lee, J. W. Bang, and S. J. Kwon. 2014. “Effect of W/C ratio on durability and porosity in cement mortar with constant cement amount.” Adv. Mater. Sci. Eng. 2014: 11. https://doi.org/10.1155/2014/273460.
Kou, S. C., C. S. Poon, and D. Chan. 2007. “Influence of fly ash as cement replacement on the properties of recycled aggregate concrete.” J. Mater. Civ. Eng. 19 (9): 709–717. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:9(709).
Kua, T. A., A. Arulrajah, S. Horpibulsuk, Y. J. Du, and S. L. Shen. 2016. “Strength assessment of spent coffee grounds-geopolymer cement utilizing slag and fly ash precursors.” Constr. Build. Mater. 115: 565–575. https://doi.org/10.1016/j.conbuildmat.2016.04.021.
Lane, D. S. 1998. Final report evaluation of concrete characteristics for rigid pavements. Charlottesville, VA: Virginia Transportation Research Council.
Latifi, N., F. Vahedifard, E. Ghazanfari, S. Horpibulsuk, A. Marto, and J. Williams. 2018a. “Sustainable improvement of clays using low-carbon nontraditional additive.” Int. J. Geomech. 18 (3): 04017162. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001086.
Latifi, N., F. Vahedifard, E. Ghazanfari, and A. S. A. Rashid. 2018b. “Sustainable usage of calcium carbide residue for stabilization of clays.” J. Mater. Civ. Eng. 30 (6): 04018099. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002313.
Lee, F. M. 1970. The chemistry of cement and concrete. London: Edward Arnold.
Limbachiya, M. C., T. Leelawat, and R. K. Dhir. 2000. “Use of recycled concrete aggregate in high-strength concrete.” Mater. Struct. 33 (9): 574–580. https://doi.org/10.1007/BF02480538.
Mehta, P. K., and P. J. Monteiro. 2006. Concrete: Microstructure, properties, and materials. New York: McGraw-Hill.
Mindess, S., J. F. Young, and D. Darwin. 2003. Concrete, 2003. Upper Saddle River, NJ: Prentice Hall.
Mohajerani, A., J. Vajna, T. H. H. Cheung, H. Kurmus, A. Arulrajah, and S. Horpibulsuk. 2017. “Practical recycling applications of crushed waste glass in construction materials: A review.” Constr. Build. Mater. 156: 443–467. https://doi.org/10.1016/j.conbuildmat.2017.09.005.
Mohammadinia, A., A. Arulrajah, A. D’Amico, and S. Horpibulsuk. 2018. “Alkali-activation of fly ash and cement kiln dust mixtures for stabilization of demolition aggregates.” Constr. Build. Mater. 186: 71–78. https://doi.org/10.1016/j.conbuildmat.2018.07.103.
Moon, D. J., and H. Y. Moon. 2002. “Effect of pore size distribution on the quantities of recycled aggregate concrete.” KSCE J. Civ. Eng. 6 (3): 289–295. https://doi.org/10.1007/BF02829151.
Muhammad, N., S. Siddiqua, and N. Latifi. 2018. “Solidification of subgrade materials using magnesium alkalinization: A sustainable additive for construction.” J. Mater. Civ. Eng. 30 (10): 04018260. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002484.
Ohama, Y. 1998. “Polymer-based admixtures.” Cem. Concr. Compos. 20 (2): 189–212. https://doi.org/10.1016/S0958-9465(97)00065-6.
Omary, S., E. Ghorbel, and G. Wardeh. 2016. “Relationships between recycled concrete aggregates characteristics and recycled aggregates concretes properties.” Constr. Build. Mater. 108: 163–174. https://doi.org/10.1016/j.conbuildmat.2016.01.042.
Otsuki, N., S. I. Miyazato, and W. Yodsudjai. 2003. “Influence of recycled aggregate on interfacial transition zone, strength, chloride penetration and carbonation of concrete.” J. Mater. Civ. Eng. 15 (5): 443–451. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:5(443).
Paranavithana, S., and A. Mohajerani. 2006. “Effects of recycled concrete aggregates on properties of asphalt concrete.” Resour. Conserv. Recycl. 48 (1): 1–12. https://doi.org/10.1016/j.resconrec.2005.12.009.
Park, S. M., J. G. Jang, S. Chae, and H. K. Lee. 2016. “An NMR spectroscopic investigation of aluminosilicate gel in alkali-activated fly ash in a -rich environment.” Materials 9 (5): 308. https://doi.org/10.3390/ma9050308.
Phetchuay, C., S. Horpibulsuk, A. Arulrajah, C. Suksiripattanapong, and A. Udomchai. 2016. “Strength development in soft marine clay stabilized by fly ash and calcium carbide residue based geopolymer.” Appl. Clay Sci. 127: 134–142. https://doi.org/10.1016/j.clay.2016.04.005.
Richardson, I. G., and G. W. Groves. 1997. “The structure of the calcium silicate hydrate phases present in hardened pastes of white portland cement/blast-furnace slag blends.” J. Mater. Sci. 32 (18): 4793–4802. https://doi.org/10.1023/A:1018639232570.
Salem, R. M., E. G. Burdette, and N. M. Jackson. 2003. “Resistance to freezing and thawing of recycled aggregate concrete.” Mater. J. 100 (3): 216–221.
Silva, R. V., J. De Brito, and R. K. Dhir. 2014. “Properties and composition of recycled aggregates from construction and demolition waste suitable for concrete production.” Constr. Build. Mater. 65: 201–217. https://doi.org/10.1016/j.conbuildmat.2014.04.117.
Singh, N. B., and S. Rai. 2001. “Effect of polyvinyl alcohol on the hydration of cement with rice husk ash.” Cem. Concr. Res. 31 (2): 239–243. https://doi.org/10.1016/S0008-8846(00)00475-0.
Somna, R., C. Jaturapitakkul, and A. M. Amde. 2012. “Effect of ground fly ash and ground bagasse ash on the durability of recycled aggregate concrete.” Cem. Concr. Compos. 34 (7): 848–854. https://doi.org/10.1016/j.cemconcomp.2012.03.003.
Sukmak, P., S. Horpibulsuk, and S. L. Shen. 2013. “Strength development in clay-fly ash geopolymer.” Constr. Build. Mater. 40: 566–574. https://doi.org/10.1016/j.conbuildmat.2012.11.015.
Sukontasukkul, P. 2004. “Tensile behaviour of hybrid fibre-reinforced concrete.” Adv. Cem. Res. 16 (3): 115–122. https://doi.org/10.1680/adcr.2004.16.3.115.
Sybertz, F., and U. Wiens. 1991. “Effect of fly ash fineness on hydration characteristics and strength development.” In Proc., Int. Conf. on Blended Cements in Construction. Sheffield, UK: Univ. of Sheffield.
Tam, V. W., X. F. Gao, and C. M. Tam. 2005. “Microstructural analysis of recycled aggregate concrete produced from two-stage mixing approach.” Cem. Concr. Res. 35 (6): 1195–1203. https://doi.org/10.1016/j.cemconres.2004.10.025.
Tangchirapat, W., R. Buranasing, and C. Jaturapitakkul. 2010. “Use of high fineness of fly ash to improve properties of recycled aggregate concrete.” J. Mater. Civ. Eng. 22 (6): 565–571. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000054.
Tangchirapat, W., R. Buranasing, C. Jaturapitakkul, and P. Chindaprasirt. 2008. “Influence of rice husk-bark ash on mechanical properties of concrete containing high amount of recycled aggregates.” Constr. Build. Mater. 22 (8): 1812–1819. https://doi.org/10.1016/j.conbuildmat.2007.05.004.
Tangchirapat, W., S. Khamklai, and C. Jaturapitakkul. 2012. “Use of ground palm oil fuel ash to improve strength, sulfate resistance, and water permeability of concrete containing high amount of recycled concrete aggregates.” Mater. Des. 41: 150–157. https://doi.org/10.1016/j.matdes.2012.04.054.
Taylor, H. F. 1997. Cement chemistry. London: Thomas Telford.
Thailand Department of Highways. 1996. Standards for highway construction. Bangkok, Thailand: Thailand Dept. of Highways.
Thong, C. C., D. C. L. Teo, and C. K. Ng. 2016. “Application of polyvinyl alcohol (PVA) in cement-based composite materials: A review of its engineering properties and microstructure behavior.” Constr. Build. Mater. 107: 172–180. https://doi.org/10.1016/j.conbuildmat.2015.12.188.
TM, ARMY. 1992. Pavement design for roads, streets, walks, and open storage areas. Washington, DC: Dept. of the Army and the Air Force.
Viswanath, P., and E. T. Thachil. 2008. “Properties of polyvinyl alcohol cement pastes.” Mater. Struct. 41 (1): 123–130. https://doi.org/10.1617/s11527-007-9224-2.
Xu, A., and S. L. Sarkar. 1994. “Microstructural development in high-volume fly-ash cement system.” J. Mater. Civ. Eng. 6 (1): 117–136. https://doi.org/10.1061/(ASCE)0899-1561(1994)6:1(117).
Xu, A., S. L. Sarkar, and L. O. Nilsson. 1993. “Effect of fly ash on the microstructure of cement mortar.” Mater. Struct. 26 (7): 414–424. https://doi.org/10.1007/BF02472942.
Yaowarat, T., S. Horpibulsuk, A. Arulrajah, M. Mirzababaei, and A. S. Rashid. 2018. “Compressive and flexural strength of polyvinyl alcohol-modified pavement concrete using recycled concrete aggregates.” J. Mater. Civ. Eng. 30 (4): 04018046. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002233.
Yoobanpot, N., P. Jamsawang, and S. Horpibulsuk. 2017. “Strength behavior and microstructural characteristics of soft clay stabilized with cement kiln dust and fly ash residue.” Appl. Clay Sci. 141: 146–156. https://doi.org/10.1016/j.clay.2017.02.028.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Aug 21, 2018
Accepted: Jan 3, 2019
Published online: Apr 26, 2019
Published in print: Jul 1, 2019
Discussion open until: Sep 26, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.