Performance Evaluation of Using Evotherm in SBS Modified Binder
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 4
Abstract
Recently, various types of additives are being used to enhance the properties of bitumen. Until now, few researchers have handled the utilization of different additives in the same binder. In this study, styrene-butadiene-styrene (SBS) and Evotherm were used both separately and in the same blend. Dynamic shear rheometer (DSR) and bending beam rheometer (BBR) tests were applied to SBS and Evotherm modified binders. SBS and Evotherm were added to pure bitumen in three different ratios. Sixteen different combinations were produced using the two additives, and a pure binder in the same binder was evaluated in the DSR test. Eight different combinations were evaluated in the BBR test. The conclusion reached was that the maximum usage of Evotherm (0.9%) induces a 20% reduction in the rutting parameter of both the 5% and 6% SBS modified binders. The 0.5% Evotherm with 4% and 5% SBS modification does not have an adverse effect on rutting performance. Evotherm modification could prevent the stiffness increment that originates from using the SBS additive, especially at high content. Using 0.7% Evotherm with 4% SBS can acquire the pure binder’s low temperature performance.
Get full access to this article
View all available purchase options and get full access to this article.
References
Aglan, H., A. Othman, L. Figueroa, and R. Rollings. 1993. “Effect of Sytrene-butadiene-styrene block copolymer on fatigue crack propagation behavior of asphalt concrete mixtures.” Transp. Res. Rec. 1417: 178–186.
Airey, G. D. 2003. “Rheological properties of styrene butadiene styrene polymer modified road bitumens.” Fuel 82 (14): 1709–1719. https://doi.org/10.1016/S0016-2361(03)00146-7.
Airey, G. D., A. E. Hunter, and B. Rahimzadeh. 2002. “The influence of geometry and sample preparation on dynamic shear reometer testing.” In Proc., 4th European Symp. on Performance of Bituminous and Hydraulic Materials in Pavements, edited by S. E. Zoorob, A. C. Collop, and S. F. Brown, 3–12. Nottingham, UK: Transportation Research Board.
Arabani, M., H. Roshani, and G. H. Hamedi. 2012. “Estimating moisture sensitivity of warm mix asphalt modified with Zycosoil as an Antistrip agent using surface free energy method.” J. Mater. Civ. Eng. 24 (7): 889–897. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000455.
Arega, Z. A., A. Bhasin, and T. De Kesel. 2013. “Influence of extended aging on the properties of asphalt composites produced using hot and warm mix methods.” Constr. Build. Mater. 44: 168–174. https://doi.org/10.1016/j.conbuildmat.2013.02.081.
ASTM. 2013. Standard test method for penetration of bituminous materials. ASTM D5/D5M. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test method for softening point of bitumen (ring-and-ball apparatus). ASTM D36/D36M-14e1. West Conshohocken, PA: ASTM.
ASTM. 2015a. Standard test method for determining the rheological properties of asphalt binder using a dynamic shear rheometer. ASTM D7175. West Conshohocken, PA: ASTM.
ASTM. 2015b. Standard test method for viscosity determination of asphalt at elevated temperatures using a rotational viscometer. ASTM D4402/D4402M. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for determining the flexural creep stiffness of asphalt binder using the bending beam rheometer (BBR). ASTM D6648. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for density of semi-solid asphalt binder (pycnometer method). ASTM D70. West Conshohocken, PA: ASTM.
Bonaquist, R. 2011. Mix design practices for warm mix asphalt. Sterling, VA: Advanced Asphalt Technologies.
Butz, T., I. Rahimian, and G. Hildebrand. 2001. “Modification of road bitumen with the Fischer-Tropsch paraffin Sasobit.” J. Appl. Asphalt Binder Techonol. 1 (2): 70–86.
Fakhri, M., A. R. Ghanizadeh, and H. Omrani. 2013. “Comparison of fatigue resistance of HMA and WMA mixtures modified by SBS.” Procedia Soc. Behav. Sci. 104: 168–177. https://doi.org/10.1016/j.sbspro.2013.11.109.
Ghabchi, R., D. Singh, M. Zaman, and Q. Tian. 2013. “Application of asphalt-aggregates ınterfacial energies to evaluate moisture-induced damage of warm mix asphalt.” Procedia Soc. Behav. Sci. 104: 29–38. https://doi.org/10.1016/j.sbspro.2013.11.095.
Hossain, Z., M. Zaman, N. M. Wasiuddin, J. Sneed, and E. O’Rear. 2011. “Rheological evaluation of warm mix and anti-stripping additives modified performance grade binders.” Road Mater. Pavement Des. 12 (4): 875–895. https://doi.org/10.1080/14680629.2011.9713898.
Hurley, G. C., and B. D. Prowell. 2006. Evaluation of Evotherm for use in warm mix asphalt. Auburn, AL: Auburn Univ.
Jamshidi, A., M. O. Hamzah, K. Kurumisawa, T. Nawa, and B. Samali. 2016. “Evaluation of sustainable technologies that upgrade the binder performance grade in asphalt pavement construction.” Mater. Des. 95: 9–20. https://doi.org/10.1016/j.matdes.2016.01.065.
Khattak, M., and G. Baladi. 1998. “Engineering properties of polymer-modified asphalt mixtures.” Transp. Res. Rec. 1638 (1): 12–22. https://doi.org/10.3141/1638-02.
Kök, B. V., M. Yılmaz, and M. Akpolat. 2014. “Evaluation of the conventional and rheological properties of SBS+Sasobit modified binder.” Constr. Build. Mater. 63: 174–179. https://doi.org/10.1016/j.conbuildmat.2014.04.015.
Liang, M., P. Liang, W. Fan, C. Qian, X. Xin, J. Shi, and G. Nan. 2015. “Thermo-rheological behavior and compatibility of modified asphalt with various styrene-butadiene structures in SBS copolymers.” Mater. Des. 88: 177–185. https://doi.org/10.1016/j.matdes.2015.09.002.
Liu, S., W. Cao, J. Fang, and S. Shang. 2009. “Variance analysis and performance evaluation of different crumb rubber modified (CRM) asphalt.” Constr. Build. Mater. 23 (7): 2701–2708. https://doi.org/10.1016/j.conbuildmat.2008.12.009.
Marasteanu, M. O., X. Li, T. R. Clyne, V. R. Voller, D. H. Timm, and D. E. Newcomb. 2004. Low temperature cracking of asphalt concrete pavements. Minneapolis: Univ. of Minnesota.
Oliveira, J. R. M., H. M. R. D. Silva, L. P. F. Abreu, and S. R. M. Fernandes. 2013. “Use of a warm mix asphalt additive to reduce the production temperatures and to improve the performance of asphalt rubber mixtures.” J. Cleaner Prod. 41: 15–22. https://doi.org/10.1016/j.jclepro.2012.09.047.
Roberts, F. L., P. S. Kandhal, E. R. Brown, D. Lee, and T. W. Kennedy. 1996. Hot mix asphalt materials; mixture design and construction. Lanham, MD: National Asphalt Pavement Association.
Rubio, M. C., G. Martínez, L. Baena, and F. Moreno. 2012. “Warm mix asphalt: An overview.” J. Cleaner Prod. 24: 76–84. https://doi.org/10.1016/j.jclepro.2011.11.053.
Sanchez-Alonso, E., A. Vega-Zamanillo, D. Castro-Fresno, and M. DelRio-Prat. 2011. “Evaluation of compactability and mechanical properties of bituminous mixes with warm additives.” Constr. Build. Mater. 25 (5): 2304–2311. https://doi.org/10.1016/j.conbuildmat.2010.11.024.
Shang, L., S. Wang, Y. Zhang, and Y. Zhang. 2011. “Pyrolyzed wax from recycled cross-linked polyethylene as warm mix asphalt (WMA) additive for SBS modified asphalt.” Constr. Build. Mater. 25 (2): 886–891. https://doi.org/10.1016/j.conbuildmat.2010.06.097.
Smith, B. S. 2006. “Design and construction of pavements in cold regions: State of the practice.” M.S. thesis, Dept. of Civil and Environmental Engineering, Brigham Young Univ.
Tarefder, R. A., and S. S. Yousefi. 2016. “Rheological examination of aging in polymer-modified asphalt.” J. Mater. Civ. Eng. 28 (2): 04015112. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001370.
Topal, A., M. Yilmaz, B. V. Kok, N. Kuloglu, and B. Sengoz. 2011. “Evaluation of rheological and image properties of styrene-butadiene-styrene and ethylene-vinyl acetate polymer modified bitumens.” J. Appl. Polym. Sci. 122 (5): 3122–3132. https://doi.org/10.1002/app.34282.
Yoo, M.-Y., S.-H. Jeong, J.-Y. Park, N.-H. Kim, and K.-W. Kim. 2011. “Low-temperature fracture characteristics of selected warm-mix asphalt concretes.” Transp. Res. Rec. 2208 (1): 40–47. https://doi.org/10.3141/2208-06.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Aug 7, 2018
Accepted: Sep 26, 2018
Published online: Jan 30, 2019
Published in print: Apr 1, 2019
Discussion open until: Jun 30, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.