Performance of Concrete with Alkali-Activated Materials and Nanosilica in Acidic Environments
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 3
Abstract
Owing to their high chemical resistance, alkali-activated materials (AAMs) may represent a promising option for repairing concrete structures affected by acidic media. However, AAMs have some technical limitations with respect to cast-in-situ applications because they require heat curing to mitigate delay in setting time, strength gain, and microstructural development at early ages. Therefore, this study investigated the performance of concrete with AAMs incorporating blends of fly ash, slag, and nanosilica cured at normal temperatures and exposed to very aggressive (10%) sulfuric acid environments. In addition to full immersion exposure for 18 weeks, a combined exposure was implemented to simulate field conditions involving alternating wetting–drying and freezing–thawing cycles combined with sulfuric acid attack. The evaluation criteria were based on visual assessment, neutralization depth, mass loss, and bond strength to substrate concrete in repair prototypes. In addition, the alterations of the microstructure of specimens were analyzed by mineralogical, thermal, and microscopy studies. The results showed that concretes prepared with fly ash–based AAMs with a small amount (6%) of nanosilica or (10%) slag without heat curing showed improved durability in sulfuric acid environments in terms of reduced penetrability of acidic media, low mass loss, and increased bond strength to substrate concrete with time. Thus, such AAMs could be a viable option for cast-in-situ repair applications of concrete elements in acidic environments.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors greatly appreciate the financial support from the Natural Sciences and Engineering Research Council of Canada (NSERC), John Glanville Memorial Scholarship, and Graduate Enhancement of Tri-Council Stipends (GETS). The IKO Construction Materials Testing Facility at the University of Manitoba in which these experiments were conducted was instrumental in this research.
References
Adak, D., M. Sarkar, and S. Mandal. 2014. “Effect of nano-silica on strength and durability of fly ash based geopolymer mortar.” Constr. Build. Mater. 70: 453–459. https://doi.org/10.1016/j.conbuildmat.2014.07.093.
Adam, A. 2009. “Strength and durability properties of alkali activated slag and fly ash-based geopolymer concrete.” Ph.D. thesis, Dept. of Civil, Environmental and Chemical Engineering, RMIT Univ.
Al Bakri Abdullah, M. M., H. Kamarudin, I. Khairul Nizar, M. Bnhussain, Y. Zarina, and A. R. Rafiza. 2012. “Correlation between ratio and fly ash/alkaline activator ratio to the strength of geopolymer.” Adv. Mater. Res. 341: 189–193.
Aliques-Granero, J., T. M. Tognonvi, and A. Tagnit-Hamou. 2017. “Durability test methods and their application to AAMs: Case of sulfuric-acid resistance.” Mater. Struct. 50 (1): 36. https://doi.org/10.1617/s11527-016-0904-7.
Amin, M., and M. T. Bassuoni. 2018. “Response of concrete with blended binders and nanoparticles to sulfuric acid attack.” Mag. Concr. Res. 70 (12): 617–632. https://doi.org/10.1680/jmacr.17.00081.
Ariffin, M. A. M., M. A. R. Bhutta, M. W. Hussin, M. M. Tahir, and N. Aziah. 2013. “Sulfuric acid resistance of blended ash geopolymer concrete.” Constr. Build. Mater. 43: 80–86. https://doi.org/10.1016/j.conbuildmat.2013.01.018.
ASTM. 2012. Standard specification for liquid membrane-forming compounds for curing concrete. ASTM C309. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for resistance of concrete to rapid freezing and thawing. ASTM C666. West Conshohocken, PA: ASTM.
ASTM. 2016a. Standard specification for chemical admixtures for concrete. ASTM C494. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39. West Conshohocken, PA: ASTM.
Bakharev, T. 2005a. “Geopolymeric materials prepared using Class F fly ash and elevated temperature curing.” Cem. Concr. Res. 35 (6): 1224–1232. https://doi.org/10.1016/j.cemconres.2004.06.031.
Bakharev, T. 2005b. “Resistance of geopolymer materials to acid attack.” Cem. Concr. Res. 35 (4): 658–670. https://doi.org/10.1016/j.cemconres.2004.06.005.
Bakharev, T., J. G. Sanjayan, and Y. B. Cheng. 2001. “Resistance of alkali-activated slag concrete to carbonation.” Cem. Concr. Res. 31 (9): 1277–1283. https://doi.org/10.1016/S0008-8846(01)00574-9.
Bassuoni, M. T., M. Nehdi, and M. Amin. 2007. “Self-compacting concrete: Using limestone to resist sulfuric acid.” ICE-Const. Mater. 160 (3): 113–123. https://doi.org/10.1680/coma.2007.160.3.113.
Bassuoni, M. T., and M. L. Nehdi. 2007. “Resistance of self-consolidating concrete to sulfuric acid attack with consecutive pH reduction.” Cem. Concr. Res. 37 (7): 1070–1084. https://doi.org/10.1016/j.cemconres.2007.04.014.
Bınıci, H., M. Y. Durgun, T. Rızaoğlu, and M. Koluçolak. 2012. “Investigation of durability properties of concrete pipes incorporating blast furnace slag and ground basaltic pumice as fine aggregates.” Scientia Iranica 19 (3): 366–372. https://doi.org/10.1016/j.scient.2012.04.007.
Cartwright, C., F. Rajabipour, and A. Radlińska. 2015. “Shrinkage characteristics of alkali-activated slag cements.” J. Mater. Civ. Eng. 27 (7): 1943–5533. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001058.
Chi, M., and R. Huang. 2013. “Binding mechanism and properties of alkali-activated fly ash/slag mortars.” Constr. Build. Mater. 40: 291–298. https://doi.org/10.1016/j.conbuildmat.2012.11.003.
Collins, F. G., and J. G. Sanjayan. 1999. “Workability and mechanical properties of alkali activated slag concrete.” Cem. Concr. Res. 29 (3): 455–458. https://doi.org/10.1016/S0008-8846(98)00236-1.
COW (City of Winnipeg). 2006. Concrete underground structures and works. COW CW2160-R7. Winnipeg, MB, Canada: COW.
CSA (Canadian Standards Association). 2013. Cementitious materials compendium. CSA A3001-13. Mississauga, ON: CSA.
CSA (Canadian Standards Association). 2014. Determination of bond strength of bonded toppings and overlays and of direct tensile strength of concrete, mortar, and grout. CSA A23.2-6B, Mississauga, ON: CSA.
Davidovits, J., D. C. Comrie, J. H. Paterson, and D. J. Ritcey. 1990. “Geopolymeric concretes for environmental protection.” Concr. Int. 12 (7): 30–40.
Deb, P. S., P. K. Sarker, and S. Barbhuiya. 2015. “Effects of nano-silica on the strength development of geopolymer cured at room temperature.” Constr. Build. Mater. 101 (Part 1): 675–683. https://doi.org/10.1016/j.conbuildmat.2015.10.044.
De Belie, N., J. Monteny, A. Beeldens, E. Vincke, D. Van Gemert, and W. Verstraete. 2004. “Experimental research and prediction of the effect of chemical and biogenic sulfuric acid on different types of commercially produced concrete sewer pipes.” Cem. Concr. Res. 34 (12): 2223–2236. https://doi.org/10.1016/j.cemconres.2004.02.015.
Fang, G., H. Bahrami, and M. Zhang. 2018. “Mechanisms of autogenous shrinkage of alkali-activated fly ash-slag pastes cured at ambient temperature within 24 h.” Constr. Build. Mater. 171: 377–387. https://doi.org/10.1016/j.conbuildmat.2018.03.155.
Ghazy, A., and M. T. Bassuoni. 2017. “Shrinkage of nano-modified fly ash concrete as repair material.” ACI Mater. J. 144 (6): 877–888. https://doi.org/10.14359/51700891.
Görhan, G., and G. Kürklü. 2014. “The influence of the NaOH solution on the properties of the fly ash-based geopolymer mortar cured at different temperatures.” Composites Part B 58: 371–377. https://doi.org/10.1016/j.compositesb.2013.10.082.
Gutiérrez-Padilla, M. G. D., A. Bielefeldt, S. Ovtchinnikov, M. Hernandez, and J. Silverstein. 2010. “Biogenic sulfuric acid attack on different types of commercially produced concrete sewer pipes.” Cem. Concr. Res. 40 (2): 293–301. https://doi.org/10.1016/j.cemconres.2009.10.002.
Hardjito, D., C. C. Cheak, and C. H. L. Ing. 2008. “Strength and setting times of low calcium fly ash-based geopolymer mortar.” Mod. Appl. Sci. 2 (4): 3–11. https://doi/org/10.5539/mas.v2n4p3.
Hardjito, D., S. E. Wallah, D. M. Sumajouw, and B. V. Rangan. 2004. “On the development of fly ash-based geopolymer concrete.” ACI Mater. J. 101 (6): 467–472.
Horpibulsuk, S., C. Suksiripattanapong, W. Samingthong, R. Rachan, and A. Arulrajah. 2015. “Durability against wetting-drying cycles of water treatment sludge-fly ash geopolymer and water treatment sludge-cement and silty clay-cement systems.” J. Mater. Civ. Eng. 28 (1): 04015078. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001351.
Ismail, I., S. A. Bernal, J. L. Provis, S. Hamdan, and J. S. van Deventer. 2013. “Microstructural changes in alkali activated fly ash/slag geopolymers with sulfate exposure.” Mater. Struct. 46 (3): 361–373. https://doi.org/10.1617/s11527-012-9906-2.
Ismail, I., S. A. Bernal, J. L. Provis, R. San Nicolas, S. Hamdan, and J. S. van Deventer. 2014. “Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash.” Cem. Concr. Compos. 45: 125–135. https://doi.org/10.1016/j.cemconcomp.2013.09.006.
Khater, H. M., B. A. El-Sabbagh, M. Fanny, M. Ezzat, and M. Lottfy. 2012. “Effect of nano-silica on alkali activated water-cooled slag geopolymer.” In Vol. 1113 of Proc., 2nd Int. Conf. on Microstructural-Related Durability of Cementitious Composites. Paris: RILEM.
Kovalchuk, G., A. Fernández-Jiménez, and A. Palomo. 2007. “Alkali-activated fly ash: Effect of thermal curing conditions on mechanical and microstructural development—Part II.” Fuel 86 (3): 315–322. https://doi.org/10.1016/j.fuel.2006.07.010.
Law, D. W., A. A. Adam, T. K. Molyneaux, and I. Patnaikuni. 2012. “Durability assessment of alkali activated slag (AAS) concrete.” Mater. Struct. 45 (9): 1425–1437. https://doi.org/10.1617/s11527-012-9842-1.
Lee, N. K., and H. K. Lee. 2013. “Setting and mechanical properties of alkali-activated fly ash/slag concrete manufactured at room temperature.” Constr. Build. Mater. 47: 1201–1209. https://doi.org/10.1016/j.conbuildmat.2013.05.107.
Lee, N. K., and H. K. Lee. 2016. “Influence of the slag content on the chloride and sulfuric acid resistances of alkali-activated fly ash/slag paste.” Cem. Concr. Compos. 72: 168–179. https://doi.org/10.1016/j.cemconcomp.2016.06.004.
Lloyd, R. R., J. L. Provis, and J. S. van Deventer. 2012. “Acid resistance of inorganic polymer binders. 1. Corrosion rate.” Mater. Struct. 45 (1–2): 1–14. https://doi.org/10.1617/s11527-011-9744-7.
Mehta, A., and R. Siddique. 2017. “Sulfuric acid resistance of fly ash based geopolymer concrete.” Constr. Build. Mater. 146: 136–143. https://doi.org/10.1016/j.conbuildmat.2017.04.077.
Monteny, J., E. Vincke, A. Beeldens, N. De Belie, L. Taerwe, D. Van Gemert, and W. Verstraete. 2000. “Chemical, microbiological, and in situ test methods for biogenic sulfuric acid corrosion of concrete.” Cem. Concr. Res. 30 (4): 623–634. https://doi.org/10.1016/S0008-8846(00)00219-2.
Nath, P., and P. K. Sarker. 2014. “Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition.” Constr. Build. Mater. 66: 163–171. https://doi.org/10.1016/j.conbuildmat.2014.05.080.
Nath, P., and P. K. Sarker. 2015. “Use of OPC to improve setting and early strength properties of low calcium fly ash geopolymer concrete cured at room temperature.” Cem. Concr. Compos. 55: 205–214. https://doi.org/10.1016/j.cemconcomp.2014.08.008.
Neto, A. A. M., M. A. Cincotto, and W. Repette. 2010. “Mechanical properties, drying and autogenous shrinkage of blast furnace slag activated with hydrated lime and gypsum.” Cem. Concr. Compos. 32 (4): 312–318. https://doi.org/10.1016/j.cemconcomp.2010.01.004.
Oh, J. E., P. J. Monteiro, S. S. Jun, S. Choi, and S. M. Clark. 2010. “The evolution of strength and crystalline phases for alkali-activated ground blast furnace slag and fly ash-based geopolymers.” Cem. Concr. Res. 40 (2): 189–196. https://doi.org/10.1016/j.cemconres.2009.10.010.
Pacheco-Torgal, F., Z. Abdollahnejad, S. Miraldo, S. Baklouti, and Y. Ding. 2012a. “An overview on the potential of geopolymers for concrete infrastructure rehabilitation.” Constr. Build. Mater. 36: 1053–1058. https://doi.org/10.1016/j.conbuildmat.2012.07.003.
Provis, J. L. 2014. “Geopolymers and other alkali activated materials: Why, how, and what?” Mater. Struct. 47 (1–2): 11–25. https://doi.org/10.1617/s11527-013-0211-5.
Puligilla, S., and P. Mondal. 2013. “Role of slag in microstructural development and hardening of fly ash-slag geopolymer.” Cem. Concr. Res. 43: 70–80. https://doi.org/10.1016/j.cemconres.2012.10.004.
Rattanasak, U., and P. Chindaprasirt. 2009. “Influence of NaOH solution on the synthesis of fly ash geopolymer.” Miner. Eng. 22 (12): 1073–1078. https://doi.org/10.1016/j.mineng.2009.03.022.
Sata, V., A. Sathonsaowaphak, and P. Chindaprasirt. 2012. “Resistance of lignite bottom ash geopolymer mortar to sulfate and sulfuric acid attack.” Cem. Concr. Compos. 34 (5): 700–708. https://doi.org/10.1016/j.cemconcomp.2012.01.010.
Sears, G. W. 1956. “Determination of specific surface area of colloidal silica by titration with sodium hydroxide.” Anal. Chem. 28 (12): 1981–1983. https://doi.org/10.1021/ac60120a048.
Song, X. J., M. Marosszeky, M. Brungs, and R. Munn. 2005. “Durability of fly ash based geopolymer concrete against sulphuric acid attack.” In Proc., Int. Conf. on Durability of Building Materials and Components, 17–20. Paris: RILEM.
Thokchom, S., P. Ghosh, and S. Ghosh. 2009a. “Acid resistance of fly ash based geopolymer mortars.” Int. J. Recent Trends Eng. Technol. 1 (6): 36–40.
Thokchom, S., P. Ghosh, and S. Ghosh. 2009b. “Resistance of fly ash based geopolymer mortars in sulfuric acid.” ARPN J. Eng. Appl. Sci. 4 (1): 65–70.
Tiznobaik, M., and M. T. Bassuoni. 2017. “Investigation into enhancing and evaluating curing efficiency of joints in concrete pavements.” Road Mater. Pavement Des. 1–17. https://doi.org/10.1080/14680629.2017.1415219. in press.
Tiznobaik, M., and M. T. Bassuoni. 2018. “A test protocol for evaluating absorption of joints in concrete pavements.” ASTM J. Test. Eval. 46 (4): 14. https://doi.org/10.1520/JTE20160297.
Ye, H., and A. Radlińska. 2016. “Shrinkage mechanisms of alkali-activated slag.” Cem. Concr. Res. 88: 126–135. https://doi.org/10.1016/j.cemconres.2016.07.001.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 31 • Issue 3 • March 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: May 7, 2018
Accepted: Sep 7, 2018
Published online: Jan 14, 2019
Published in print: Mar 1, 2019
Discussion open until: Jun 14, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.