Feasibility of Alkali-Activated Slag Paste as Injection Material for Rehabilitation of Concrete Structures
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 10
Abstract
Alkali-activated materials (AAMs) have recently been used as a suitable replacement for conventional ordinary portland cement (OPC) mixtures. This study evaluates rheological, injectability, and mechanical properties of alkali-activated slag (AAS) mixes to assess the possibility of using AAS pastes as coating mortars for the rehabilitation of concrete structures. Mixtures are produced with the incorporation of silica fume (SF) up to 15% of total binder weight in AAS pastes. A combination of sodium hydroxide (NaOH) and sodium silicate (water glass) is used to activate aluminosilicate sources. Water glass:NaOH ratios of 0.4 and 0.5 and activator solution:pozzolan ratios of 0.55 and 0.65 are selected after initial attempts to evaluate the effect of activator solution characteristics on the rheology properties of AAS mixtures. Samples are prepared in two moisture conditions (dry and damp) in order to assess the effect of moisture presence on the performance of AAS injection pastes. Setting time, fluidity, injectability, tensile strength, capillary absorption, and slant shear tests are conducted on AAS pastes. Microstructure analysis is performed on the selected mixtures. According to results obtained from limited experimental work conducted in this study, 5% SF addition results in higher setting time and injectability of AAS pastes. In addition, it is found that an increase in water glass content in AAS pastes results in lower setting time and fluidity, which in turn results in a low level of injectability. The results of tests conducted on damp and dry samples show a high level of compatibility of AAS paste with moisture presence.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors respectfully acknowledge the Iran National Science Foundation (INSF) and are grateful for the financial support received from the foundation.
References
ACI (American Concrete Institute). 2006. Guide for the design and construction of structural concrete reinforced with FRP bars. ACI 440.1R-06. Farmington Hills, MI: ACI.
Ardalan, B., A. J. Reza, and R. D. Hooton. 2017. “Workability retention and compressive strength of self-compacting concrete incorporating pumice powder and silica fume.” Constr. Build. Mater. 134: 116–122. https://doi.org/10.1016/j.conbuildmat.2016.12.090.
Assaad, J. J., and Y. Daou. 2014. “Cementitious grouts with adapted rheological properties for injection by vacuum techniques.” Cem. Concr. Res. 59: 43–54. https://doi.org/10.1016/j.cemconres.2014.01.021.
Assaedi, H., F. U. A. Shaikh, and I. M. Low. 2016. “Influence of mixing methods of nano silica on the microstructural and mechanical properties of flax fabric reinforced geopolymer composites.” Constr. Build. Mater. 123: 541–552. https://doi.org/10.1016/j.conbuildmat.2016.07.049.
ASTM. 2013. Standard test methods for time of setting of hydraulic cement by vicat needle. ASTM C191. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard specification for finishing hydrated lime. ASTM C206. West Conshohocken, PA: ASTM.
Bernal, S. A., R. M. de Gutiérrez, A. L. Pedraza, J. L. Provis, E. D. Rodriguez, and S. Delvasto. 2011. “Effect of binder content on the performance of alkali-activated slag concretes.” Cem. Concr. Res. 41 (1): 1–8. https://doi.org/10.1016/j.cemconres.2010.08.017.
Binda, L., G. Baronio, C. Tiraboschi, and C. Tedeschi. 2003. “Experimental research for the choice of adequate materials for the reconstruction of the Cathedral of Noto.” Constr. Build. Mater. 17 (8): 629–639. https://doi.org/10.1016/S0950-0618(03)00059-X.
Bras, A., and F. M. Henriques. 2012. “Natural hydraulic lime based grouts—The selection of grout injection parameters for masonry consolidation.” Constr. Build. Mater. 26 (1): 135–144. https://doi.org/10.1016/j.conbuildmat.2011.05.012.
BSI (British Standards Institution). 2004. Products and systems for the protection and repair of concrete structures. Test methods. Determination of injectability and splitting test. BS EN 1771. London: BSI.
Clark, L. A., and B. S. Gill. 1985. “Shear strength 01 smooth unreinforced construction joints.” Mag. Concr. Res. 37 (131): 95–100. https://doi.org/10.1680/macr.1985.37.131.95.
Collins, F., and J. Sanjayan. 1998. “Early age strength and workability of slag pastes activated by NaOH and .” Cem. Concr. Res. 28 (5): 655–664. https://doi.org/10.1016/S0008-8846(98)00025-8.
Duan, P., C. Yan, and W. Luo. 2016. “A novel waterproof, fast setting and high early strength repair material derived from metakaolin geopolymer.” Constr. Build. Mater. 124: 69–73. https://doi.org/10.1016/j.conbuildmat.2016.07.058.
Duan, P., C. Yan, and W. Zhou. 2017. “Compressive strength and microstructure of fly ash based geopolymer blended with silica fume under thermal cycle.” Cem. Concr. Compos. 78 (4): 108–119. https://doi.org/10.1016/j.cemconcomp.2017.01.009.
Gao, X., Q. L. Yu, and H. J. H. Brouwers. 2015. “Characterization of alkali activated slag–fly ash blends containing nano-silica.” Constr. Build. Mater. 98: 397–406. https://doi.org/10.1016/j.conbuildmat.2015.08.086.
Gifford, P. M., and J. E. Gillott. 1997. “Behaviour of mortar and concrete made with activated blast furnace slag cement.” Can. J. Civ. Eng. 24 (2): 237–249. https://doi.org/10.1139/l96-099.
Guerrieri, M., and J. Sanjayan. 2011. “Investigation of the cause of disintegration of alkali-activated slag at temperature exposure of 50°C.” J. Mater. Civ. Eng. 23 (12): 1589–1595. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000313.
Han, D., and M. Han. 2015. “Effect of pre-mixed cement on the dispersion of silica fume in ternary blended cementitious paste.” Supplement, Mater. Res. Innovations 19 (S5): S5-700–S5-707. https://doi.org/10.1179/1432891714Z.0000000001179.
Issa, C. A., and P. Debs. 2007. “Experimental study of epoxy repairing of cracks in concrete.” Constr. Build. Mater. 21 (1): 157–163. https://doi.org/10.1016/j.conbuildmat.2005.06.030.
Jambunathan, N., J. G. Sanjayan, Z. Pan, G. Li, Y. Liu, A. H. Korayem, W. H. Duan, and F. Collins. 2013. “The role of alumina on performance of alkali-activated slag paste exposed to 50°C.” Cem. Concr. Res. 54: 143–150. https://doi.org/10.1016/j.cemconres.2013.09.009.
Jorne, F., F. M. Henriques, and L. G. Baltazar. 2015. “Injection capacity of hydraulic lime grouts in different porous media.” Mater. Struct. 48 (7): 2211–2233. https://doi.org/10.1617/s11527-014-0304-9.
Joshaghani, A., A. Moazenian, and R. A. Shuaibu. 2017. “Experimental study on the use of trass as a supplementary cementitious material in pervious concrete.” J. Environ. Sci. Eng. A 1: 39–52.
Khater, H. M. 2013. “Effect of silica fume on the characterization of the geopolymer materials.” Int. J. Adv. Struct. Eng. 5 (1): 12. https://doi.org/10.1186/2008-6695-5-12.
Kramar, S., A. Šajna, and V. Ducman. 2016. “Assessment of alkali activated mortars based on different precursors with regard to their suitability for concrete repair.” Constr. Build. Mater. 124: 937–944. https://doi.org/10.1016/j.conbuildmat.2016.08.018.
Lee, N., and H. Lee. 2013. “Setting and mechanical properties of alkali-activated fly ash/slag concrete manufactured at room temperature.” Constr. Build. Mater. 47: 1201–1209. https://doi.org/10.1016/j.conbuildmat.2013.05.107.
Li, Z., Z. Pan, Y. Liu, L. He, W. Duan, F. Collins, and J. Sanjayan. 2014. “Effects of mineral admixtures and lime on disintegration of alkali-activated slag exposed to 50°C.” Constr. Build. Mater. 70: 254–261. https://doi.org/10.1016/j.conbuildmat.2014.07.101.
Mehta, P., and O. Gjørv. 1982. “Properties of portland cement concrete containing fly ash and condensed silica-fume.” Cem. Concr. Res. 12 (5): 587–595. https://doi.org/10.1016/0008-8846(82)90019-9.
Musiket, K., M. Rosendahl, and Y. Xi. 2016. “Fracture of recycled aggregate concrete under high loading rates.” J. Mater. Civ. Eng. 28 (6): 864–870. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001513.
Naderi, M. 2009. “Analysis of the slant shear test.” J. Adhes. Sci. Technol. 23 (2): 229–245. https://doi.org/10.1163/156856108X369589.
Nadoushan, M. J., and A. A. Ramezanianpour. 2016. “The effect of type and concentration of activators on flowability and compressive strength of natural pozzolan and slag-based geopolymers.” Constr. Build. Mater. 111: 337–347. https://doi.org/10.1016/j.conbuildmat.2016.02.086.
Part, W. K., M. Ramli, and C. B. Cheah. 2015. “An overview on the influence of various factors on the properties of geopolymer concrete derived from industrial by-products.” Constr. Build. Mater. 77: 370–395. https://doi.org/10.1016/j.conbuildmat.2014.12.065.
Pavel, K., P. Oleg, V. Hryhorii, and L. Serhii. 2017. “The development of alkali-activated cement mixtures for fast rehabilitation and strengthening of concrete structures.” Procedia Eng. 195: 142–146. https://doi.org/10.1016/j.proeng.2017.04.536.
Provis, J. L., and J. S. J. van Deventer. 2009. Geopolymers structures, processing, properties and industrial applications. Boca Raton, FL: CRC Press.
Sahmaran, M., H. E. Yücel, G. Yildirim, M. Al-Emam, and M. Lachemi. 2014. “Investigation of the bond between concrete substrate and ECC overlays.” J. Mater. Civ. Eng. 26 (1): 167–174. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000805.
Shi, C., P. Krivenko, and D. Roy. 2006a. “Activated cements and concretes.” In Alkali-activated cements and concretes, 200–245. Boca Raton, FL: CRC Press.
Shi, C., D. Roy, and P. Krivenko. 2006b. Alkali-activated cements and concretes. CRC.
Skvara, F. 1985. “Alkali-activated slag cements.” J. Stavivo, Prague 63 (1): 16–20.
Tan, O., G. Gungormus, and A. S. Zaimoglu. 2014. “Effect of bentonite, fly ash and silica fume cement injections on uniaxial compressive strength of granular bases.” KSCE J. Civ. Eng. 18 (6): 1650–1654. https://doi.org/10.1007/s12205-014-0227-6.
Xu, H., and J. Van Deventer. 2000. “The geopolymerisation of alumino-silicate minerals.” Int. J. Miner. Process. 59 (3): 247–266. https://doi.org/10.1016/S0301-7516(99)00074-5.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Sep 15, 2017
Accepted: Feb 23, 2018
Published online: Jul 17, 2018
Published in print: Oct 1, 2018
Discussion open until: Dec 17, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.