Particle Size Effect of Volcanic Ash towards Developing Engineered Portland Cements
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 8
Abstract
Promoting the use of naturally available materials as a partial substitute to portland cement can be a viable solution for producing low carbon footprint and durable cements. This work assessed the chemomechanical behavior of hardened cement pastes with partial replacement of ordinary portland cement (OPC) with volcanic ash up to 50%. Volcanic ash was ground to two different mean sizes (17 and 6 μm) and then used to prepare cement–volcanic ash blends of various proportions. Mixtures were cured for 28 days; then the hardened cement paste specimens were studied for the effects of partial substitution with volcanic ash on mechanical properties, pore structure, and microstructure. The volcanic ash was engineered by decreasing the particle size, thus allowing for a greater extent of OPC replacement with volcanic ash. Strength increase was observed for specimens with up to 40% substitution of OPC with volcanic ash of a mean size of 6 μm, and this increase was attributed to the denser pore structure observed via mercury intrusion porosimetry (MIP) studies. Densification of specimens was attributed to the generation of secondary calcium silicate hydrate (C-S-H) gels when smaller-sized volcanic ash was used. This study provides a multiscale insight into engineering portland cement blends with partial replacement of portland cement with finer volcanic ash.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was sponsored by the Kuwait Foundation for the Advancement of Sciences. The project was conducted as part of the Kuwait–Massachusetts Institute of Technology (MIT) signature project on sustainability of Kuwait’s built environment under the direction of Professor Oral Buyukozturk. Use of the Advanced Photon Source at Argonne National Laboratory was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. The authors would like to thank 11-BM staff Dr. Saul H. Lapidus and Lynn Ribaud. This work made use of the Materials Research Science and Engineering Centers (MRSEC) Shared Experimental Facilities at MIT, supported by the National Science Foundation under Award No. DMR-1419807. We thank Dr. Charlie Settens from the Center for Material Science and Engineering (CMSE) from MIT for helping with XRD analysis. We would like to thank Patrick Boisvert for assisting in scanning electron microscopy (SEM) imaging at the CMSE laboratory in MIT. The authors are thankful to Douglas Shattuck, Vern Roberston, and Masateru Shibata from JEOL USA Inc. for helping with the BSE microscopy and EDS analysis.
References
Alper, A. 2012. Phase diagrams 6-V: Materials science and technology. London, UK: Elsevier.
ASTM. 2014. Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency. ASTM C305-14. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM C109. West Conshohocken, PA: ASTM.
Barker, A. P. 1989. “An electron optical examination of zoning in blastfurnace slag hydrates. I: Slag cement pastes at early ages.” Adv. Cem. Res. 2 (8): 171–179. https://doi.org/10.1680/adcr.1989.2.8.171.
Bayuseno, A. P., and W. W. Schmahl. 2010. “Understanding the chemical and mineralogical properties of the inorganic portion of MSWI bottom ash.” Waste Manage. 30 (8–9): 1509–1520. https://doi.org/10.1016/j.wasman.2010.03.010.
Bernal, S. A., M. C. G. Juenger, X. Ke, W. Matthes, B. Lothenbach, N. De Belie, and J. L. Provis. 2016. “Characterization of supplementary cementitious materials by thermal analysis.” Mater. Struct. 50 (26): 1–13. https://doi.org/10.1617/s11527-016-0909-2.
Brew, D. R. M., and F. P. Glasser. 2005. “Synthesis and characterisation of magnesium silicate hydrate gels.” Cem. Concr. Res. 35 (1): 85–98. https://doi.org/10.1016/j.cemconres.2004.06.022.
Celik, K., M. D. Jackson, M. Mancio, C. Meral, A. H. Emwas, P. K. Mehta, and P. J. M. Monteiro. 2014. “High-volume natural volcanic pozzolan and limestone powder as partial replacements for portland cement in self-compacting and sustainable concrete.” Cem. Concr. Compos. 45: 136–147. https://doi.org/10.1016/j.cemconcomp.2013.09.003.
Chindaprasirt, P., C. Jaturapitakkul, and T. Sinsiri. 2005. “Effect of fly ash fineness on compressive strength and pore size of blended cement paste.” Cem. Concr. Compos. 27 (4): 425–428. https://doi.org/10.1016/j.cemconcomp.2004.07.003.
Conjeaud, M., and H. Boyer. 1980. “Some possibilities of Raman microprobe in cement chemistry.” Cem. Concr. Res. 10 (1): 61–70. https://doi.org/10.1016/0008-8846(80)90052-6.
Diamond, S. 2000. “Mercury porosimetry: An inappropriate method for the measurement of pore size distributions in cement-based materials.” Cem. Concr. Res. 30 (10): 1517–1525. https://doi.org/10.1016/S0008-8846(00)00370-7.
Engelsen, C. J., H. A. van der Sloot, G. Wibetoe, G. Petkovic, E. Stoltenberg-Hansson, and W. Lund. 2009. “Release of major elements from recycled concrete aggregates and geochemical modelling.” Cem. Concr. Res. 39 (5): 446–459. https://doi.org/10.1016/j.cemconres.2009.02.001.
Fisher, R. V., and H.-U. Schmincke. 1984. “Alteration of volcanic glass.” Chap. 12 in Pyroclastic rocks, 312–345. Berlin, Germany: Springer.
Garcia-Lodeiro, I., A. Palomo, A. Fernández-Jiménez, and D. E. Macphee. 2011. “Compatibility studies between N-A-S-H and C-A-S-H gels. Study in the ternary diagram .” Cem. Concr. Res. 41 (9): 923–931. https://doi.org/10.1016/j.cemconres.2011.05.006.
Gardner, L. J., S. A. Bernal, S. A. Walling, C. L. Corkhill, J. L. Provis, and N. C. Hyatt. 2015. “Characterisation of magnesium potassium phosphate cements blended with fly ash and ground granulated blast furnace slag.” Cem. Concr. Res. 74: 78–87. https://doi.org/10.1016/j.cemconres.2015.01.015.
Herfort, D., and B. Lothenbach. 2015. “Ternary phase diagrams applied to hydrated cement.” In A practical guide to microstructural analysis of cementitious materials, 485–502. Boca Raton, FL: CRC Press.
Hewlett, P. 2003. Lea’s chemistry of cement and concrete. New York, NY: Elsevier.
Hipedinger, N. E., A. N. Scian, and E. F. Aglietti. 2002. “Magnesia–phosphate bond for cold-setting cordierite-based refractories.” Cem. Concr. Res. 32 (5): 675–682. https://doi.org/10.1016/S0008-8846(01)00725-6.
Hossain, K. M. A. 2003. “Blended cement using volcanic ash and pumice.” Cem. Concr. Res. 33 (10): 1601–1605. https://doi.org/10.1016/S0008-8846(03)00127-3.
Hossain, K. M. A., and M. Lachemi. 2006. “Development of volcanic ash concrete: Strength, durability and micro-structural investigations.” ACI Mater. J. 103 (1): 11–17.
Hossain, K. M. A., and M. Lachemi. 2007. “Strength, durability and micro-structural aspects of high performance volcanic ash concrete.” Cem. Concr. Res. 37 (5): 759–766. https://doi.org/10.1016/j.cemconres.2007.02.014.
Husain, A., K. Kupwade-Patil, A. F. Al-Aibani, and M. F. Abdulsalam. 2017. “In situ electrochemical impedance characterization of cement paste with volcanic ash to examine early stage of hydration.” Constr. Build. Mater. 133: 107–117. https://doi.org/10.1016/j.conbuildmat.2016.12.054.
Jackson, M. D., S. R. Mulcahy, H. Chen, Y. Li, Q. Li, P. Cappelletti, and H.-R. Wenk. 2017. “Phillipsite and Al-tobermorite mineral cements produced through low-temperature water-rock reactions in Roman marine concrete.” Am. Mineral. 102 (7): 1435–1450. https://doi.org/10.2138/am-2017-5993CCBY.
Jackson, M. D., G. Vola, D. Všianský, J. Oleson, B. Scheetz, C. Brandon, and R. Hohlfelder. 2012. “Cement microstructures and durability in ancient roman seawater concretes.” In Historic mortars, edited by J. Válek, J. J. Hughes, and C. J. W. P. Groot, 49–76. Dordrecht, Netherlands: Springer.
Krauskopf, K. B., and D. K. Bird. 1995. Introduction to geochemistry. New York, NY: McGraw-Hill.
Kupwade-Patil, K., A. F. Al-Aibani, M. F. Abdulsalam, C. Mao, A. Bumajdad, S. D. Palkovic, and O. Büyüköztürk. 2016a. “Microstructure of cement paste with natural pozzolanic volcanic ash and portland cement at different stages of curing.” Constr. Build. Mater. 113: 423–441. https://doi.org/10.1016/j.conbuildmat.2016.03.084.
Kupwade-Patil, K., M. Tyagi, C. M. Brown, and O. Büyüköztürk. 2016b. “Water dynamics in cement paste at early age prepared with pozzolanic volcanic ash and ordinary portland cement using quasielastic neutron scattering.” Cem. Concr. Res. 86: 55–62. https://doi.org/10.1016/j.cemconres.2016.04.011.
Leonelli, C., E. Kamseu, D. N. Boccaccini, U. C. Melo, A. Rizzuti, N. Billong, and P. Miselli. 2007. “Volcanic ash as alternative raw materials for traditional vitrified ceramic products.” Adv. Appl. Ceram. 106 (3): 135–141. https://doi.org/10.1179/174367607X159329.
Lloyd, R., J. Provis, and J. J. Deventer. 2009. “Microscopy and microanalysis of inorganic polymer cements. 1: Remnant fly ash particles.” J. Mater. Sci. 44 (2): 608–619. https://doi.org/10.1007/s10853-008-3077-0.
Luke, K., H. F. W. Taylor, and G. L. Kalousek. 1981. “Some factors affecting formation of truscottite and xonotlite at 300–350°C.” Cem. Concr. Res. 11 (2): 197–203. https://doi.org/10.1016/0008-8846(81)90060-0.
Masmoudi, R., K. Kupwade-Patil, A. Bumajdad, and O. Büyüköztürk. 2017. “In situ Raman studies on cement paste prepared with natural pozzolanic volcanic ash and ordinary portland cement.” Constr. Build. Mater. 148: 444–454. https://doi.org/10.1016/j.conbuildmat.2017.05.016.
Massazza, F. 2002. “Properties and applications of natural pozzolanas.” In Structure and performance of cements, edited by J. Bensted, and J. P. Barnes, 326–352. London: Spon Press.
Matschei, T., B. Lothenbach, and F. P. Glasser. 2007. “The role of calcium carbonate in cement hydration.” Cem. Concr. Res. 37 (4): 551–558. https://doi.org/10.1016/j.cemconres.2006.10.013.
Mindess, S. 2000. “The strength and fracture of concrete: The role of the calcium hydroxide.” In Proc., Workshop on the Role of Calcium Hydroxide in Concrete, 143–154. Holmes Beach, FL.
Moon, J., S. Bae, K. Celik, S. Yoon, K.-H. Kim, K. S. Kim, and P. J. M. Monteiro. 2014. “Characterization of natural pozzolan-based geopolymeric binders.” Cem. Concr. Compos. 53: 97–104. https://doi.org/10.1016/j.cemconcomp.2014.06.010.
Neville, A. M. 2011. Properties of concrete. Essex, England: Prentice Hall.
Nied, D., K. Enemark-Rasmussen, E. L’Hopital, J. Skibsted, and B. Lothenbach. 2016. “Properties of magnesium silicate hydrates (M-S-H).” Cem. Concr. Res. 79: 323–332. https://doi.org/10.1016/j.cemconres.2015.10.003.
Pauly, B. D., P. Schiffman, R. A. Zierenberg, and D. A. Clague. 2011. “Environmental and chemical controls on palagonitization.” Geochem. Geophys. Geosyst. 12 (12): Q12017. https://doi.org/10.1029/2011GC003639.
Puertas, F., M. Palacios, H. Manzano, J. S. Dolado, A. Rico, and J. Rodríguez. 2011. “A model for the C-A-S-H gel formed in alkali-activated slag cements.” J. Eur. Ceram. Soc. 31 (12): 2043–2056. https://doi.org/10.1016/j.jeurceramsoc.2011.04.036.
Sbordoni-Mora, L. 1981. “Les matériaux des enduits traditionnels.” In Mortars, cements and grouts used in the conservation of historic buildings/Mortiers, ciments et coulis utilisés dans la conservation des bâtiments historiques, 375–383. Rome, Italy: International Centre for the Study of the Preservation and Restoration of Cultural Property.
Scrivener, K. L., and R. J. Kirkpatrick. 2008. “Innovation in use and research on cementitious material.” Cem. Concr. Res. 38 (2): 128–136. https://doi.org/10.1016/j.cemconres.2007.09.025.
Skalny, J. P., J. Gebauer, and I. Odler. 2001. Materials science of concrete: Calcium hydroxide in concrete. Westerville, OH: American Ceramic Society.
Slanička, Š. 1991. “The influence of fly ash fineness on the strength of concrete.” Cem. Concr. Res. 21 (2–3): 285–296. https://doi.org/10.1016/0008-8846(91)90010-F.
Snellings, R., G. Mertens, and J. Elsen. 2012. “Supplementary cementitious materials.” Rev. Mineral. Geochem. 74 (1): 211–278. https://doi.org/10.2138/rmg.2012.74.6.
Sorrell, C. A. 1960. “Reaction sequence and structural changes in cordierite refractories.” J. Am. Ceram. Soc. 43 (7): 337–343. https://doi.org/10.1111/j.1151-2916.1960.tb13667.x.
Taylor, H. F. W. 1997. Cement chemistry. 2nd ed. London, UK: Thomas Telford.
Walton, A. W., P. Schiffman, and G. L. Macpherson. 2005. “Alteration of hyaloclastites in the HSDP 2 Phase 1 drill core: 2. Mass balance of the conversion of sideromelane to palagonite and chabazite.” Geochem. Geophys. Geosyst. 6 (9): Q09G19. https://doi.org/10.1029/2004GC000903.
Wang, J., B. H. Toby, P. L. Lee, L. Ribaud, S. M. Antao, C. Kurtz, M. Ramanathan, R. B. V. Dreele, and M. A. Beno. 2008. “A dedicated powder diffraction beamline at the advanced photon source: Commissioning and early operational results.” Rev. Sci. Instrum. 79: 085105. https://doi.org/10.1063/1.2969260.
Zhang, T., L. J. Vandeperre, and C. R. Cheeseman. 2014. “Formation of magnesium silicate hydrate (M-S-H) cement pastes using sodium hexametaphosphate.” Cem. Concr. Res. 65: 8–14. https://doi.org/10.1016/j.cemconres.2014.07.001.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: May 2, 2017
Accepted: Jan 23, 2018
Published online: Jun 5, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 5, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.