Experimental and Numerical Investigation of Fatigue in Base-Rendering Mortar Used in Façades Undergoing Thermal Cycles
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 8
Abstract
Ceramic tile coating systems are widely used on building façades. Such façades generally consist of a few layers of materials such as rough cast, base-rendering mortar, adhesive layer for tiles, ceramic tiles, and grout between the tiles. Building coatings, in general, are subject to a variety of hazardous weather conditions including temperature variations which, combined with different mechanical properties of the façade material layers, produce thermal expansions and stresses in façades. Currently, studies of façade fatigue produced by such stress variations are not reported in the technical literature but it is a very important issue for construction companies and property owners. The purpose of this research is to evaluate the fatigue of the base-rendering mortar layer and estimate the life cycle of ceramic tile façades traditionally used in South American cities. The paper also presents a practical methodology based on experimental and numerical evaluations to estimate the fatigue life of base-rendering mortar under temperature transients of typical building façades. The Wöhler diagram of the base-rendering mortar is experimentally obtained and the thermal stress assessment done with finite-element models. With the alternating stress and the Wöhler diagram, it was possible to evaluate the lifetime of the base-rendering mortar layer in some façades. A case study is presented, showing critical situations where fatigue life can be just a few years, as observed in practice.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful to the Brazilian National Council for Scientific and Technological Development (CNPq) and to the Brazilian Coordination for the Improvement of Higher Education Personnel (CAPES) for their supporting funds for this research.
References
Aas-Jakobsen, K. 1970. Fatigue of concrete beams and columns. Trondheim, Norway: NTH Institute for Betonkonstruksjoner.
ABNT (Brazilian Association for Technical Standards). 2005a. Mortar applied on walls and ceilings—Determination of tensile and compression strengths: Procedures. ABNT NBR13279. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association for Technical Standards). 2005b. Mortars applied on walls and ceilings: Requirements. ABNT NBR13281. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association for Technical Standards). 2008. Central and unitary air condition systems. 3: Indoor air quality. ABNT NBR16401. Rio de Janeiro, Brazil: ABNT.
Anderson, T. L. 2005. Fracture mechanics: Fundamentals and applications. Boca Raton, FL: CRC Press.
Arrivabene, V. 1994. Resistⓔncia dos materiais. São Paulo, Brazil: Makron Books.
ASTM. 2011. Standard specification for application of portland cement-based plaster. ASTM C926-11a. West Conshohocken, PA: ASTM.
Balocco, C., G. Grazzini, and A. Cavalera. 2008. “Transient analysis of an external building cladding.” Energy Build. 40 (7): 1273–1277. https://doi.org/10.1016/j.enbuild.2007.11.008.
Barishpolsky, B. 1980. “A combined experimental and numerical method for the solution of generalized elasticity problems.” Exp. Mech. 20 (10): 345–349. https://doi.org/10.1007/BF02321121.
Bröeke, D. 1982. Elementary engineering fracture mechanics. Dordrecht, Netherlands: Kluwer Academic.
CEN (European Committee for Standardization). 2010. Specification for mortar for masonry. 1: Rendering and plastering mortar. EN998-1. Brussels, Belgium: CEN.
Cervo, T. 2004. “Study of the fatigue strength of cement portland concrete for paving.” [In Portuguese.] Ph.D. thesis, Dept. of Engineering, Univ. of São Paulo.
Chagas, S. V. M. 2009. “Study and proposal of a fatigue resistance model for base rendering mortars of coating in plane and 3D stress states.” [In Portuguese.] M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Brasilia.
Collins, J. 1993. Failure of materials in mechanical design. New York: Willey.
Cornelissen, H. A. W. 1984. “Fatigue failure of concrete in tension.” Heron 29 (4): 1–68.
Frota, A. B., and S. R. Schiffer. 2003. Thermal comfort manual. São Paulo, Brazil: Studio Nobel.
Gao, L., and C.-T. Hsu. 1998. “Fatigue of concrete under uniaxial compression cyclic loading.” ACI Mater. J. 95 (5): 575–581.
Gao, X., and R. Rowlands. 2000. “Hybrid method for stress analysis of finite three-dimensional elastic components.” Int. J. Solids Struct. 37 (19): 2727–2751. https://doi.org/10.1016/S0020-7683(99)00111-0.
Gomes, R. 1962. Climate conditioning of the building envelope for housing. Lisbon, Portugal.
Hess, A., and A. Weintraub. 2009. Oscar Niemeyer buildings. New York: Rizzoli.
Hsu, T. T. C. 1981. “Fatigue of plain concrete.” ACI J. 78 (4): 292–305.
INMET (Instituto Nacional de Meteorologia). 2012. “Brazilian National Institute of Meteorology.” Accessed February 20, 2005. http://www.inmet.gov.br.
ISO. 1994. Moderate thermal environments—Determination of the PMV and PPD indices and specification of the conditions for thermal comfort. ISO7730. Geneva: ISO.
Kupfer, H., H. K. Hilsdorf, and H. Rusch. 1969. “Behavior of concrete under biaxial stresses.” ACI J. Proc. 66 (8): 656–666.
Lee, M., and B. I. G. Barr. 2004. “An overview of the fatigue behaviour of plain and fiber reinforced concrete.” Cem. Concr. Compos. 26 (4): 299–305. https://doi.org/10.1016/S0958-9465(02)00139-7.
McCormac, J. C., and S. F. Csernak. 2012. Structural Steel Design. Upper Saddle River, NJ: Prentice Hall.
Peterson, R. E. 1974. Stress concentration factors. New York: Wiley.
Rivero, R. 1985. Natural thermal conditioning: Architecture and climate. Rio Grande do Sul, Brazil: Federal Univ.
Saito, M. 1987. “Characteristics of microcracking in concrete under static and repeated tensile loading.” Cem. Concr. Res. 17 (2): 211–218. https://doi.org/10.1016/0008-8846(87)90104-9.
Santos Botas, S. M., M. R. Silva Veiga, and A. L. Velosa. 2015. “Adhesion of air lime–based mortars to old tiles: Moisture and open porosity influence in tile/mortar interfaces.” J. Mater. Civ. Eng. 27 (5): 04014161. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001108.
Saraiva, A. 1998. “Contribution to the study of thermal stresses in ceramic tile coating system.” [In Portuguese.] M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Brasilia.
Shigley, J. E., and C. R. Mischke. 2004. Mechanical engineering design. New York: McGraw-Hill.
Silva, M. N. B. 1999. “Evaluation with the finite element method of thermo-mechanical stresses in façade coating systems.” [In Portuguese.] M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Brasilia.
Silvestre, J. D., and J. de Brito. 2010. “Inspection and repair of ceramic tiling within a building management system.” J. Mater. Civ. Eng. 22 (1): 39–48. https://doi.org/10.1061/(ASCE)0899-1561(2010)22:1(39).
Spagnoli, A., M. Migliazza, M. Zucali, and A. Ferrero. 2014. “Thermal degradation in Carrara marbles as the cause of deformation of cladding slabs.” Frattura ed Integrità Strutturale 8 (30): 145–152. https://doi.org/10.3221/IGF-ESIS.30.19.
Tepfers, R., and T. Kutti. 1979. “Fatigue strength of plain, ordinary and lightweight concrete.” ACI J. 76 (5): 635–652.
Thomaz, E. 1989. Cracks in buildings: Causes, prevention and recovery. São Paulo, Brazil: PINI Edition.
Uchôa, J. C. 2007. “Numerical and experimental procedure for fatigue strength assessment in building coating system.” [In Portuguese.] M.Sc. thesis, Dept. of Civil and Environmental Engineering, Univ. of Brasilia.
Wanderley, I. 2006. “Tiles in Brazilian architecture: The panels of Atlos Bulcao.” [In Portuguese.] M.Sc. thesis, Engineering School of São Carlos, Univ. of São Paulo.
Wang, H. L., and Y. P. Song. 2010. “Fatigue capacity of plain concrete under fatigue loading with constant confined stress.” Mater. Struct. 44 (1): 253–262. https://doi.org/10.1617/s11527-010-9624-6.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jul 31, 2017
Accepted: Jan 4, 2018
Published online: Jun 8, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 8, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.