Toward the Development of Sustainable Concretes with Recycled Concrete Aggregates: Comprehensive Review of Studies on Mechanical Properties
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 9
Abstract
In recent years, the increased rate of urbanization has led to the generation and release of large amounts of construction and demolition (C&D) waste. From the viewpoint of environmental preservation and effective utilization of resources, it is beneficial and necessary to reuse C&D waste. Recycled concrete aggregate, which is obtained from C&D waste, is currently being considered as an alternative aggregate for structural concrete. Recycled aggregate concrete (RAC), an ecofriendly concrete produced by partial or full substitution of natural aggregates with recycled concrete aggregates in a concrete mix, has drawn much attention recently. Over the last decade, a significant volume of studies has been reported in the literature on the behavior of RACs. This paper summarizes the literature dealing with the mechanical properties (and the parameters affecting them) of RACs produced using coarse recycled concrete aggregates published between 1978 and 2017. In order to provide a comprehensive understanding of the behavior of RAC, this review takes into account more than 200 published studies. The review also discusses the less understood influences of aggregate surface treatment, aggregate moisture state, and concrete mixing on the behavior of RAC. To the best of the authors’ knowledge, this is the first review dealing with all the potential influential factors affecting the mechanical properties of RAC. Hence, this review is expected to help researchers better understand the behavior of this construction material.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support from the National Natural Science Foundation of China through Grant 51650110495 and from the University of Adelaide through a Research Excellence Grant awarded to the third author.
References
Abbas, A., G. Fathifazl, B. Fournier, O. B. Isgor, R. Zavadil, A. G. Razaqpur, and S. Foo. 2009. “Quantification of the residual mortar content in recycled concrete aggregates by image analysis.” Mater. Charact. 60 (7): 716–728. https://doi.org/10.1016/j.matchar.2009.01.010.
Abbas, A., G. Fathifazl, O. B. Isgor, A. G. Razaqpur, B. Fournier, and S. Foo. 2008. “Proposed method for determining the residual mortar content of recycled concrete aggregates.” J. ASTM Int. 5 (1): 1–12. https://doi.org/10.1520/JAI101087.
AbdElhakam, A., A. E. Mohamed, and E. Awad. 2012. “Influence of self-healing, mixing method and adding silica fume on mechanical properties of recycled aggregates concrete.” Constr. Build. Mater. 35: 421–427. https://doi.org/10.1016/j.conbuildmat.2012.04.013.
Achtemichuk, S., J. Hubbard, R. Sluce, and M. H. Shehata. 2009. “The utilization of recycled concrete aggregate to produce controlled low-strength materials without using portland cement.” Cem. Concr. Compos. 31 (8): 564–569. https://doi.org/10.1016/j.cemconcomp.2008.12.011.
Adams, M. P., T. Fu, A. G. Cabrera, M. Morales, J. H. Ideker, and O. B. Isgor. 2016. “Cracking susceptibility of concrete made with coarse recycled concrete aggregates.” Constr. Build. Mater. 102: 802–810. https://doi.org/10.1016/j.conbuildmat.2015.11.022.
Adams, M. P., A. Jones, S. Beauchemin, R. Johnson, B. Fournier, M. Shehata, J. E. Tanner, and J. Ideker. 2013. “Applicability of the accelerated mortar bar test for alkali-silica reactivity of recycled concrete aggregates.” Adv. Civ. Eng. Mater. 2 (1): 78–96. https://doi.org/10.1520/ACEM20120030.
Afroughsabet, V., L. Biolzi, and T. Ozbakkaloglu. 2017. “Influence of double hooked-end steel fibers and slag on mechanical and durability properties of high-performance recycled aggregate concrete.” Compos. Struct. 181: 273–284. https://doi.org/10.1016/j.compstruct.2017.08.086.
Ajdukiewicz, A., and A. Kliszczewicz. 2002. “Influence of recycled aggregates on mechanical properties of HS/HPC.” Cem. Concr. Compos. 24 (2): 269–279. https://doi.org/10.1016/S0958-9465(01)00012-9.
Ajdukiewicz, A. B., and A. T. Kliszczewicz. 2007. “Comparative tests of beams and columns made of recycled aggregate concrete and natural aggregate concrete.” J. Adv. Concr. Technol. 5 (2): 259–273. https://doi.org/10.3151/jact.5.259.
Akbarnezhad, A., K. C. G. Ong, C. T. Tam, and M. H. Zhang. 2013. “Effects of the parent concrete properties and crushing procedure on the properties of coarse recycled concrete aggregates.” J. Mater. Civ. Eng. 25 (12): 1795–1802. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000789.
Akçaoğlu, T., M. Tokyay, and T. Çelik. 2002. “Effect of coarse aggregate size on interfacial cracking under uniaxial compression.” Mater. Lett. 57 (4): 828–833. https://doi.org/10.1016/S0167-577X(02)00881-9.
Alexander, M. G., and T. I. Milne. 1995. “Influence of cement blend and aggregate type on the stress-strain behavior and elastic modulus of concrete.” ACI Mater. J. 92 (3): 227–235.
Andreu, G., and E. Miren. 2014. “Experimental analysis of properties of high performance recycled aggregate concrete.” Constr. Build. Mater. 52: 227–235. https://doi.org/10.1016/j.conbuildmat.2013.11.054.
Ann, K. Y., H. Y. Moon, Y. B. Kim, and J. Ryou. 2008. “Durability of recycled aggregate concrete using pozzolanic materials.” Waste Manage. 28 (6): 993–999. https://doi.org/10.1016/j.wasman.2007.03.003.
Bairagi, N. K., K. Ravande, and V. K. Pareek. 1993. “Behaviour of concrete with different proportions of natural and recycled aggregates.” Resour. Conserv. Recycl. 9 (1): 109–126. https://doi.org/10.1016/0921-3449(93)90036-F.
Bairagi, N. K., H. S. Vidyadhara, and K. Ravande. 1990. “Mix design procedure for recycled aggregate concrete.” Constr. Build. Mater. 4 (4): 188–193. https://doi.org/10.1016/0950-0618(90)90039-4.
Barbudo, A., J. de Brito, L. Evangelista, M. Bravo, and F. Agrela. 2013. “Influence of water-reducing admixtures on the mechanical performance of recycled concrete.” J. Cleaner Prod. 59: 93–98. https://doi.org/10.1016/j.jclepro.2013.06.022.
Behera, M., S. K. Bhattacharyya, A. K. Minocha, R. Deoliya, and S. Maiti. 2014. “Recycled aggregate from C&D waste & its use in concrete—A breakthrough towards sustainability in construction sector: A review.” Constr. Build. Mater. 68: 501–516. https://doi.org/10.1016/j.conbuildmat.2014.07.003.
Belén, G. F., M. A. Fernando, C. L. Diego, and S. P. Sindy. 2011. “Stress-strain relationship in axial compression for concrete using recycled saturated coarse aggregate.” Constr. Build. Mater. 25 (5): 2335–2342. https://doi.org/10.1016/j.conbuildmat.2010.11.031.
Beltrán, M. G., A. Barbudo, F. Agrela, A. P. Galvín, and J. R. Jiménez. 2014. “Effect of cement addition on the properties of recycled concretes to reach control concretes strengths.” J. Cleaner Prod. 79: 124–133. https://doi.org/10.1016/j.jclepro.2014.05.053.
Berndt, M. L. 2009. “Properties of sustainable concrete containing fly ash, slag and recycled concrete aggregate.” Constr. Build. Mater. 23 (7): 2606–2613. https://doi.org/10.1016/j.conbuildmat.2009.02.011.
Brand, A. S., J. R. Roesler, and A. Salas. 2015. “Initial moisture and mixing effects on higher quality recycled coarse aggregate concrete.” Constr. Build. Mater. 79: 83–89. https://doi.org/10.1016/j.conbuildmat.2015.01.047.
Butler, L., J. S. West, and S. L. Tighe. 2011. “The effect of recycled concrete aggregate properties on the bond strength between RCA concrete and steel reinforcement.” Cem. Concr. Res. 41 (10): 1037–1049. https://doi.org/10.1016/j.cemconres.2011.06.004.
Butler, L., J. S. West, and S. L. Tighe. 2013. “Effect of recycled concrete coarse aggregate from multiple sources on the hardened properties of concrete with equivalent compressive strength.” Constr. Build. Mater. 47: 1292–1301. https://doi.org/10.1016/j.conbuildmat.2013.05.074.
Butler, L., J. S. West, and S. L. Tighe. 2014. “Towards the classification of recycled concrete aggregates: Influence of fundamental aggregate properties on recycled concrete performance.” J. Sustainable Cem. Based Mater. 3 (2): 140–163. https://doi.org/10.1080/21650373.2014.909752.
Buyle-Bodin, F., and R. Hadjieva-Zaharieva. 2002. “Influence of industrially produced recycled aggregates on flow properties of concrete.” Mater. Struct. 35 (8): 504–509. https://doi.org/10.1007/BF02483138.
Çakır, Ö. 2014. “Experimental analysis of properties of recycled coarse aggregate (RCA) concrete with mineral additives.” Constr. Build. Mater. 68: 17–25. https://doi.org/10.1016/j.conbuildmat.2014.06.032.
Çakır, Ö., and Ö. Ö. Sofyanlı. 2015. “Influence of silica fume on mechanical and physical properties of recycled aggregate concrete.” HBRC J. 11 (2): 157–166. https://doi.org/10.1016/j.hbrcj.2014.06.002.
Carneiro, J. A., P. R. L. Lima, M. B. Leite, and R. D. Toledo Filho. 2014. “Compressive stress-strain behavior of steel fiber reinforced-recycled aggregate concrete.” Cem. Concr. Compos. 46: 65–72. https://doi.org/10.1016/j.cemconcomp.2013.11.006.
Casuccio, M., M. C. Torrijos, G. Giaccio, and R. Zerbino. 2008. “Failure mechanism of recycled aggregate concrete.” Constr. Build. Mater. 22 (7): 1500–1506. https://doi.org/10.1016/j.conbuildmat.2007.03.032.
ChakradharaRao, M., S. K. Bhattacharyya, and S. V. Barai. 2011. “Behaviour of recycled aggregate concrete under drop weight impact load.” Constr. Build. Mater. 25 (1): 69–80.
Chen, B. 2013. “Basic mechanical properties and microstructural analysis of recycled concrete.” J. Wuhan Univ. Technol. -Mater. Sci. Ed. 28 (1): 104–109. https://doi.org/10.1007/s11595-013-0649-x.
Chen, H. J., T. Yen, and K. H. Chen. 2003. “Use of building rubbles as recycled aggregates.” Cem. Concr. Res. 33 (1): 125–132. https://doi.org/10.1016/S0008-8846(02)00938-9.
Corinaldesi, V. 2010. “Mechanical and elastic behaviour of concretes made of recycled-concrete coarse aggregates.” Constr. Build. Mater. 24 (9): 1616–1620. https://doi.org/10.1016/j.conbuildmat.2010.02.031.
Corinaldesi, V. 2011. “Structural concrete prepared with coarse recycled concrete aggregate: From investigation to design.” Adv. Civ. Eng. 1–6. https://doi.org/10.1155/2011/283984.
Corinaldesi, V., and G. Moriconi. 2009. “Influence of mineral additions on the performance of 100% recycled aggregate concrete.” Constr. Build. Mater. 23 (8): 2869–2876. https://doi.org/10.1016/j.conbuildmat.2009.02.004.
Corinaldesi, V., G. Orlandi, and G. Moriconi. 2002. “Self-compacting concrete incorporating recycled aggregate.” Vol. 4 of Innovations and developments in concrete materials and construction edited by R. K. Dhir, P. C. Hewlett, and L. J. Csetenyi, 455–464. London: Thomas Telford.
Cui, Z. L., S. S. Lu, and Z. S. Wang. 2012. “Influence of recycled aggregate on strength and anti-carbonation properties of recycled aggregate concrete.” J. Build. Mater. 15 (2): 264–267.
de Juan, M. S., and P. A. Gutiérrez. 2004. “Influence of recycled aggregate quality on concrete properties.” In Proc., Conf. on Use of Recycled Materials in Building and Structures, 9–11. Paris: RILEM Publications.
de Juan, M. S., and P. A. Gutiérrez. 2009. “Study on the influence of attached mortar content on the properties of recycled concrete aggregate.” Constr. Build. Mater. 23 (2): 872–877. https://doi.org/10.1016/j.conbuildmat.2008.04.012.
de Oliveira, M. B., and E. Vazquez. 1996. “The influence of retained moisture in aggregates from recycling on the properties of new hardened concrete.” Waste Manage. 16 (1): 113–117. https://doi.org/10.1016/S0956-053X(96)00033-5.
Dhir, R. K. 1999. “Sustainability of recycled concrete aggregate for use in BS 5328 designated mixes.” Proc., ICE-Structures and Buildings 134 (3): 257–274. https://doi.org/10.1680/istbu.1999.31568.
Dilbas, H., M. Şimşek, and Ö. Çakır. 2014. “An investigation on mechanical and physical properties of recycled aggregate concrete (RAC) with and without silica fume.” Constr. Build. Mater. 61: 50–59. https://doi.org/10.1016/j.conbuildmat.2014.02.057.
Domingo-Cabo, A., C. Lázaro, F. López-Gayarre, M. A. Serrano-López, P. Serna, and J. O. Castaño-Tabares. 2009. “Creep and shrinkage of recycled aggregate concrete.” Constr. Build. Mater. 23 (7): 2545–2553. https://doi.org/10.1016/j.conbuildmat.2009.02.018.
Du, T., W. Wang, Z. Liu, H. Lin, and T. Guo. 2010. “The complete stress-strain curve of recycled aggregate concrete under uniaxial compression loading.” J. Wuhan Univ. Technol. (Mater. Sci. Ed.) 25 (5): 862–865. https://doi.org/10.1007/s11595-010-0109-9.
Duan, Z. H., and C. S. Poon. 2014. “Properties of recycled aggregate concrete made with recycled aggregates with different amounts of old adhered mortars.” Mater. Des. 58: 19–29. https://doi.org/10.1016/j.matdes.2014.01.044.
Elices, M., and C. G. Rocco. 2008. “Effect of aggregate size on the fracture and mechanical properties of a simple concrete.” Eng. Fract. Mech. 75 (13): 3839–3851. https://doi.org/10.1016/j.engfracmech.2008.02.011.
Etxeberria, M., A. R. Mari, and E. Vazquez. 2007a. “Recycled aggregate concrete as structural material.” Mater. Struct. 40 (5): 529–541. https://doi.org/10.1617/s11527-006-9161-5.
Etxeberria, M., V, A. Marí, and M. Barra. 2007b. “Influence of amount of recycled coarse aggregates and production process on properties of recycled aggregate concrete.” Cem. Concr. Res. 37 (5): 735–742. https://doi.org/10.1016/j.cemconres.2007.02.002.
Evangelista, L., and J. de Brito. 2014. “Concrete with fine recycled aggregates: A review.” Eur. J. Environ. Civ. Eng. 18 (2): 129–172. https://doi.org/10.1080/19648189.2013.851038.
Evangelista, L., and J. De Brito. 2007. “Mechanical behaviour of concrete made with fine recycled concrete aggregates.” Cem. Concr. Compos. 29 (5): 397–401. https://doi.org/10.1016/j.cemconcomp.2006.12.004.
Fathifazl, G., A. Abbas, A. G. Razaqpur, O. B. Isgor, B. Fournier, and S. Foo. 2009. “New mixture proportioning method for concrete made with coarse recycled concrete aggregate.” J. Mater. Civ. Eng. 21 (10): 601–611. https://doi.org/10.1061/(ASCE)0899-1561(2009)21:10(601).
Fathifazl, G., A. G. Razaqpur, O. B. Isgor, A. Abbas, B. Fournier, and S. Foo. 2011. “Creep and drying shrinkage characteristics of concrete produced with coarse recycled concrete aggregate.” Cem. Concr. Compos. 33 (10): 1026–1037. https://doi.org/10.1016/j.cemconcomp.2011.08.004.
Ferreira, L., J. de Brito, and M. Barra. 2011. “Influence of the pre-saturation of recycled coarse concrete aggregates on concrete properties.” Mag. Concr. Res. 63 (8): 617–627. https://doi.org/10.1680/macr.2011.63.8.617.
Folino, P., and H. Xargay. 2014. “Recycled aggregate concrete—Mechanical behavior under uniaxial and triaxial compression.” Constr. Build. Mater. 56: 21–31. https://doi.org/10.1016/j.conbuildmat.2014.01.073.
Fonseca, N., J. De Brito, and L. Evangelista. 2011. “The influence of curing conditions on the mechanical performance of concrete made with recycled concrete waste.” Cem. Concr. Compos. 33 (6): 637–643. https://doi.org/10.1016/j.cemconcomp.2011.04.002.
Gayarre, F. L., C. L. C. Pérez, M. A. S. López, and A. D. Cabo. 2014. “The effect of curing conditions on the compressive strength of recycled aggregate concrete.” Constr. Build. Mater. 53: 260–266. https://doi.org/10.1016/j.conbuildmat.2013.11.112.
Gholampour, A., A. H. Gandomi, and T. Ozbakkaloglu. 2017. “New formulations for mechanical properties of recycled aggregate concrete using gene expression programming.” Constr. Build. Mater. 130: 122–145. https://doi.org/10.1016/j.conbuildmat.2016.10.114.
Gómez-Soberón, J. 2002. “Porosity of recycled concrete with substitution of recycled concrete aggregate: An experimental study.” Cem. Concr. Res. 32 (8): 1301–1311. https://doi.org/10.1016/S0008-8846(02)00795-0.
Gonçalves, A., A. Esteves, and M. Vieira. 2004. “Influence of recycled concrete aggregates on concrete durability.” In Proc., Int. RILEM Conf. on the Use of Recycled Materials in Buildings and Structures. Paris: RILEM Publications.
González-Fonteboa, B., and F. Martínez-Abella. 2008. “Concretes with aggregates from demolition waste and silica fume.” Build. Environ. 43 (4): 429–437. https://doi.org/10.1016/j.buildenv.2007.01.008.
González-Fonteboa, B., F. Martínez-Abella, J. Eiras-López, and S. Seara-Paz. 2011. “Effect of recycled coarse aggregate on damage of recycled concrete.” Mater. Struct. 44 (10): 1759–1771. https://doi.org/10.1617/s11527-011-9736-7.
González-Fonteboa, B., F. Martínez-Abella, M. F. Herrador, and S. Seara-Paz. 2012. “Structural recycled concrete: Behaviour under low loading rate.” Constr. Build. Mater. 28 (1): 111–116. https://doi.org/10.1016/j.conbuildmat.2011.08.010.
Gonzalez-Taboada, I., B. Gonzalez-Fonteboa, F. Martinez-Abella, and D. Carro-Lopez. 2016. “Study of recycled concrete aggregate quality and its relationship with recycled concrete compressive strength using database analysis.” Materiales de Construcción 66 (323): 1–18. https://doi.org/10.3989/mc.2016.06415.
Guneyisi, E., M. Gesoğlu, Q. Kareem, and S. İpek. 2016. “Effect of different substitution of natural aggregate by recycled aggregate on performance characteristics of pervious concrete.” Mater. Struct. 49 (1–2): 521–536.
Hani, S. A., I. A. Rahman, and H. M. Saman. 2015. “Enhancing the performance of recycled aggregate concrete using micronized biomass silica.” In Proc., CIEC, 65–77. Singapore: Springer.
Hansen, T. C. 1986. “Recycled aggregates and recycled aggregate concrete second state-of-the-art report developments 1945–1985.” Mater. Struct. 19 (3): 201–246. https://doi.org/10.1007/BF02472036.
Hansen, T. C. 2004. Vol. 6 of Recycling of demolished concrete and masonry. Boca Raton, FL: CRC Press.
Hansen, T. C., and E. Boegh. 1985. “Elasticity and drying shrinkage concrete of recycled-aggregate.” ACI J. Proc. 82 (5): 648–652.
Hassan, A. A. A., M. K. Ismail, and J. Mayo. 2015. “Mechanical properties of self-consolidating concrete containing lightweight recycled aggregate in different mixture compositions.” J. Build. Eng. 4: 113–126. https://doi.org/10.1016/j.jobe.2015.09.005.
Hoffmann, C., S. Schubert, A. Leemann, and M. Motavalli. 2012. “Recycled concrete and mixed rubble as aggregates: Influence of variations in composition on the concrete properties and their use as structural material.” Constr. Build. Mater. 35: 701–709. https://doi.org/10.1016/j.conbuildmat.2011.10.007.
Hou, Y. L., and G. Zheng. 2013. “Mechanical properties of recycled aggregate concrete in different age.” J. Build. Mater. 16 (4): 683–687.
Hu, M. P. 2007. “Mechanical properties of concrete prepared with different recycled coarse aggregates replacement rate.” [In Chinese.] Concrete 2: 52–54.
Ismail, S., and M. Ramli. 2013. “Engineering properties of treated recycled concrete aggregate (RCA) for structural applications.” Constr. Build. Mater. 44: 464–476. https://doi.org/10.1016/j.conbuildmat.2013.03.014.
Ismail, S., and M. Ramli. 2014. “Mechanical strength and drying shrinkage properties of concrete containing treated coarse recycled concrete aggregates.” Constr. Build. Mater. 68: 726–739. https://doi.org/10.1016/j.conbuildmat.2014.06.058.
Kabir, A., N. U. Ahmed, and M. S. Alam. 2015. “Effect of cement proportion on strength of recycled aggregate concrete.” Int. J. Struct. Civ. Eng. Res. 4 (4): 341–346. https://doi.org/10.18178/ijscer.4.4.341-346.
Kang, T. H. K., W. Kim, Y. K. Kwak, and S. G. Hong. 2014. “Flexural testing of reinforced concrete beams with recycled concrete aggregates (with appendix).” ACI Struct. J. 111 (3): 607–616. https://doi.org/10.14359/51686622.
Katz, A. 2003. “Properties of concrete made with recycled aggregate from partially hydrated old concrete.” Cem. Concr. Res. 33 (5): 703–711. https://doi.org/10.1016/S0008-8846(02)01033-5.
Katz, A. 2004. “Treatments for the improvement of recycled aggregate.” J. Mater. Civ. Eng. 16 (6): 597–603. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:6(597).
Kheder, G. F., and S. A. Al-Windawi. 2005. “Variation in mechanical properties of natural and recycled aggregate concrete as related to the strength of their binding mortar.” Mater. Struct. 38 (7): 701–709. https://doi.org/10.1007/BF02484315.
Kikuchi, M., Y. Dosho, M. Narikawa, and T. Miura. 1998. “Application of re-cycled aggregate concrete for structural concrete. Part 1—Experimental study on the quality of recycled aggregate and recycled aggregate concrete.” In Proc., Int. Symp. on Use of Recycled Concrete Aggregate, 55–68. London: Thomas Telford.
Kim, S. W., H. D. Yun, W. S. Park, and Y. I. Jang. 2015. “Bond strength prediction for deformed steel rebar embedded in recycled coarse aggregate concrete.” Mater. Des. 83: 257–269. https://doi.org/10.1016/j.matdes.2015.06.008.
Kong, D., T. Lei, J. Zheng, C. Ma, J. Jiang, and J. Jiang. 2010. “Effect and mechanism of surface-coating pozzalanics materials around aggregate on properties and ITZ microstructure of recycled aggregate concrete.” Constr. Build. Mater. 24 (5): 701–708. https://doi.org/10.1016/j.conbuildmat.2009.10.038.
Kou, S. C., and C. S. Poon. 2009. “Properties of self-compacting concrete prepared with coarse and fine recycled concrete aggregates.” Cem. Concr. Compos. 31 (9): 622–627. https://doi.org/10.1016/j.cemconcomp.2009.06.005.
Kou, S. C., and C. S. Poon. 2012. “Enhancing the durability properties of concrete prepared with coarse recycled aggregate.” Constr. Build. Mater. 35: 69–76. https://doi.org/10.1016/j.conbuildmat.2012.02.032.
Kou, S. C., and C. S. Poon. 2015. “Effect of the quality of parent concrete on the properties of high performance recycled aggregate concrete.” Constr. Build. Mater. 77: 501–508. https://doi.org/10.1016/j.conbuildmat.2014.12.035.
Kou, S. C., C. S. Poon, and F. Agrela. 2011. “Comparisons of natural and recycled aggregate concretes prepared with the addition of different mineral admixtures.” Cem. Concr. Compos. 33 (8): 788–795. https://doi.org/10.1016/j.cemconcomp.2011.05.009.
Kou, S. C., C. S. Poon, and D. Chan. 2007. “Influence of fly ash as cement replacement on the properties of recycled aggregate concrete.” J. Mater. Civ. Eng. 19 (9): 709–717. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:9(709).
Kou, S. C., C. S. Poon, and D. Chan. 2008. “Influence of fly ash as a cement addition on the hardened properties of recycled aggregate concrete.” Mater. Struct. 41 (7): 1191–1201. https://doi.org/10.1617/s11527-007-9317-y.
Kou, S. C., B. J. Zhan, and C. S. Poon. 2012. “Feasibility study of using recycled fresh concrete waste as coarse aggregates in concrete.” Constr. Build. Mater. 28 (1): 549–556. https://doi.org/10.1016/j.conbuildmat.2011.08.027.
Kumutha, R., and K. Vijai. 2010. “Strength of concrete incorporating aggregates recycled from demolition waste.” ARPN J. Eng. Appl. Sci. 5 (5): 64–71.
Lee, G. C., and H. B. Choi. 2013. “Study on interfacial transition zone properties of recycled aggregate by micro-hardness test.” Constr. Build. Mater. 40: 455–460. https://doi.org/10.1016/j.conbuildmat.2012.09.114.
Leite, M. B. 2001. “Evaluation of the mechanical properties of concrete produced with recycled aggregates from construction and demolition wastes.” Ph.D. dissertation, Federal Univ. of Rio Grande doSul.
Levy, S. M., and P. Helene. 2004. “Durability of recycled aggregates concrete: A safe way to sustainable development.” Cem. Concr. Res. 34 (11): 1975–1980. https://doi.org/10.1016/j.cemconres.2004.02.009.
Li, G., Y. Zhao, S. S. Pang, and Y. Li. 1999. “Effective Young’s modulus estimation of concrete.” Cem. Concr. Res. 29 (9): 1455–1462. https://doi.org/10.1016/S0008-8846(99)00119-2.
Li, H., and J. Z. Xiao. 2012. “On fatigue strength of recycled aggregate concrete based on its elastic modulus.” J. Build. Mater. 15 (2): 260–263.
Li, J., H. Xiao, and Y. Zhou. 2009. “Influence of coating recycled aggregate surface with pozzolanic powder on properties of recycled aggregate concrete.” Constr. Build. Mater. 23 (3): 1287–1291. https://doi.org/10.1016/j.conbuildmat.2008.07.019.
Li, J. B. 2004. “Study on mechanical behavior of recycled aggregate concrete.” Master dissertation, Tongji Univ.
Li, W., J. Xiao, Z. Sun, S. Kawashima, and S. P. Shah. 2012. “Interfacial transition zones in recycled aggregate concrete with different mixing approaches.” Constr. Build. Mater. 35: 1045–1055. https://doi.org/10.1016/j.conbuildmat.2012.06.022.
Li, X. 2008. “Recycling and reuse of waste concrete in China: Part I. Material behaviour of recycled aggregate concrete.” Resour. Conserv. Recycling 53 (1): 36–44. https://doi.org/10.1016/j.resconrec.2008.09.006.
Liang, Y. C., Z. M. Ye, F. Vernerey, and Y. Xi. 2015. “Development of processing methods to improve strength of concrete with 100% recycled coarse aggregate.” J. Mater. Civ. Eng. 27 (5): 04014163. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000909.
Lim, J. C., and T. Ozbakkaloglu. 2014. “Stress–strain model for normal- and light-weight concretes under uniaxial and triaxial compression.” Constr. Build. Mater. 71: 492–509. https://doi.org/10.1016/j.conbuildmat.2014.08.050.
Lima, C., A. Caggiano, C. Faella, E. Martinelli, M. Pepe, and R. Realfonzo. 2013. “Physical properties and mechanical behaviour of concrete made with recycled aggregates and fly ash.” Constr. Build. Mater. 47: 547–559. https://doi.org/10.1016/j.conbuildmat.2013.04.051.
Limbachiya, M., M. S. Meddah, and Y. Ouchagour. 2012a. “Performance of portland/silica fume cement concrete produced with recycled concrete aggregate.” ACI Mater. J. 109 (1): 91–100.
Limbachiya, M., M. S. Meddah, and Y. Ouchagour. 2012b. “Use of recycled concrete aggregate in fly-ash concrete.” Constr. Build. Mater. 27 (1): 439–449. https://doi.org/10.1016/j.conbuildmat.2011.07.023.
Limbachiya, M. C., T. Leelawat, and R. K. Dhir. 2000. “Use of recycled concrete aggregate in high-strength concrete.” Mater. Struct. 33 (9): 574–580. https://doi.org/10.1007/BF02480538.
Lin, Y. H., Y. Y. Tyan, T. P. Chang, and C. Y. Chang. 2004. “An assessment of optimal mixture for concrete made with recycled concrete aggregates.” Cem. Concr. Res. 34 (8): 1373–1380. https://doi.org/10.1016/j.cemconres.2003.12.032.
Liu, Q., J. Xiao, and Z. Sun. 2011. “Experimental study on the failure mechanism of recycled concrete.” Cem. Concr. Res. 41 (10): 1050–1057. https://doi.org/10.1016/j.cemconres.2011.06.007.
Lotfi, S., M. Eggimann, E. Wagner, R. Mroz, and J. Deja. 2015. “Performance of recycled aggregate concrete based on a new concrete recycling technology.” Constr. Build. Mater. 95: 243–256. https://doi.org/10.1016/j.conbuildmat.2015.07.021.
Manzi, S., C. Mazzotti, and M. C. Bignozzi. 2013. “Short and long-term behavior of structural concrete with recycled concrete aggregate.” Cem. Concr. Compos. 37: 312–318. https://doi.org/10.1016/j.cemconcomp.2013.01.003.
Marinković, S., V. Radonjanin, M. Malešev, and I. Ignjatović. 2010. “Comparative environmental assessment of natural and recycled aggregate concrete.” Waste Manage. 30 (11): 2255–2264. https://doi.org/10.1016/j.wasman.2010.04.012.
Martínez-Lage, I., F. Martínez-Abella, C. Vázquez-Herrero, and J. L. Pérez-Ordóñez. 2012. “Properties of plain concrete made with mixed recycled coarse aggregate.” Constr. Build. Mater. 37: 171–176. https://doi.org/10.1016/j.conbuildmat.2012.07.045.
Mas, B., A. Cladera, T. D. Olmo, and F. Pitarch. 2012. “Influence of the amount of mixed recycled aggregates on the properties of concrete for non-structural use.” Constr. Build. Mater. 27 (1): 612–622. https://doi.org/10.1016/j.conbuildmat.2011.06.073.
Matias, D., J. de Brito, A. Rosa, and D. Pedro. 2013. “Mechanical properties of concrete produced with recycled coarse aggregates – Influence of the use of superplasticizers.” Constr. Build. Mater. 44: 101–109. https://doi.org/10.1016/j.conbuildmat.2013.03.011.
McNeil, K., and T. H. K. Kang. 2013. “Recycled concrete aggregates: A review.” Int. J. Concr. Struct. Mater. 7 (1): 61–69. https://doi.org/10.1007/s40069-013-0032-5.
Medina, C., W. Zhu, T. Howind, M. I. S. de Rojas, and M. Frías. 2014. “Influence of mixed recycled aggregate on the physical-mechanical properties of recycled concrete.” J. Cleaner Prod. 68: 216–225. https://doi.org/10.1016/j.jclepro.2014.01.002.
Medina, C., W. Zhu, T. Howind, M. I. S. de Rojas, and M. Frías. 2015. “Influence of interfacial transition zone on engineering properties of the concrete manufactured with recycled ceramic aggregate.” J. Civ. Eng. Manage. 21 (1): 83–93. https://doi.org/10.3846/13923730.2013.802727.
Mefteh, H., O. Kebaïli, H. Oucief, L. Berredjem, and N. Arabi. 2013. “Influence of moisture conditioning of recycled aggregates on the properties of fresh and hardened concrete.” J. Cleaner Prod. 54: 282–288. https://doi.org/10.1016/j.jclepro.2013.05.009.
Mehta, P. K., and H. Meryman. 2009. “Tools for reducing carbon emissions due to cement consumption.” Structure 1 (1): 11–15.
Montgomery, D. G., and D. Sturgiss. 1996. “Properties of concrete incorporating recycled concrete aggregates.” In Proc., National Symp. on the Use of Recycled Materials in Engineering Construction. Barton, Australia: Engineers Australia.
Murali, G., V. C. M. Vardhan, R. Gavriela, G. J. Janani, N. Shifu, and R. Sri. 2012. “Experimental Study on recycled aggregate concrete.” Int. J. Eng. Res. Appl. 2 (2): 407–410.
Nagataki, S. 2001. “Recycling of demolished concrete.” ACI Spec. Publ. 200: 1–20.
Nagataki, S., A. Gokce, T. Saeki, and M. Hisada. 2004. “Assessment of recycling process induced damage sensitivity of recycled concrete aggregates.” Cem. Concr. Res. 34 (6): 965–971. https://doi.org/10.1016/j.cemconres.2003.11.008.
Neville, A. M. 1995. Properties of concrete. 4th ed. London: Longman Group.
Nixon, P. J. 1978. “Recycled concrete as an aggregate for concrete—A review.” Matériauxet Construction 11 (5): 371–378. https://doi.org/10.1007/BF02473878.
Otsuki, N., S. I. Miyazato, and W. Yodsudjai. 2003. “Influence of recycled aggregate on interfacial transition zone, strength, chloride penetration and carbonation of concrete.” J. Mater. Civ. Eng. 15 (5): 443–451. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:5(443).
Ozbakkaloglu, T., A. Gholampour, and T. Xie. 2017. “Mechanical and durability properties of recycled aggregate concrete: Effect of recycled aggregate properties and content.” J. Mater. Civ. Eng. 30 (2): 04017275. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002142.
Özturan, T., and C. Çeçen. 1997. “Effect of coarse aggregate type on mechanical properties of concretes with different strengths.” Cem. Concr. Res. 27 (2): 165–170. https://doi.org/10.1016/S0008-8846(97)00006-9.
Padmini, A. K., K. Ramamurthy, and M. S. Mathews. 2009. “Influence of parent concrete on the properties of recycled aggregate concrete.” Constr. Build. Mater. 23 (2): 829–836. https://doi.org/10.1016/j.conbuildmat.2008.03.006.
Paine, K. A., and R. K. Dhir. 2010. “Recycled aggregates in concrete: a performance related approach.” Mag. Concr. Res. 62 (7): 519–530. https://doi.org/10.1680/macr.2010.62.7.519.
Pandurangan, K., A. Dayanithy, and S. O. Prakash. 2016. “Influence of treatment methods on the bond strength of recycled aggregate concrete.” Constr. Build. Mater. 120: 212–221. https://doi.org/10.1016/j.conbuildmat.2016.05.093.
Pedro, D., J. de Brito, and L. Evangelista. 2014. “Influence of the use of recycled concrete aggregates from different sources on structural concrete.” Constr. Build. Mater. 71: 141–151. https://doi.org/10.1016/j.conbuildmat.2014.08.030.
Pedro, D., J. de Brito, and L. Evangelista. 2015. “Performance of concrete made with aggregates recycled from precasting industry waste: Influence of the crushing process.” Mater. Struct. 48 (12): 3965–3978. https://doi.org/10.1617/s11527-014-0456-7.
Pepe, M., R. D. Toledo Filho, E. A. Koenders, and E. Martinelli. 2014. “Alternative processing procedures for recycled aggregates in structural concrete.” Constr. Build. Mater. 69: 124–132. https://doi.org/10.1016/j.conbuildmat.2014.06.084.
Pereira, P., L. Evangelista, and J. de Brito. 2012a. “The effect of superplasticizers on the mechanical performance of concrete made with fine recycled concrete aggregates.” Cem. Concr. Compos. 34 (9): 1044–1052. https://doi.org/10.1016/j.cemconcomp.2012.06.009.
Pereira, P., L. Evangelista, and J. De Brito. 2012b. “The effect of superplasticizers on the workability and compressive strength of concrete made with fine recycled concrete aggregates.” Constr. Build. Mater. 28 (1): 722–729. https://doi.org/10.1016/j.conbuildmat.2011.10.050.
Pickel, D. 2014. “Recycled concrete aggregate: Influence of aggregate pre-saturation and curing conditions on the hardened properties of concrete.” Ph.D. dissertation, Univ. of Waterloo.
Poon, C. S., and D. Chan. 2007. “Effects of contaminants on the properties of concrete paving blocks prepared with recycled concrete aggregates.” Constr. Build. Mater. 21 (1): 164–175. https://doi.org/10.1016/j.conbuildmat.2005.06.031.
Poon, C. S., S. C. Kou, and L. Lam. 2007. “Influence of recycled aggregate on slump and bleeding of fresh concrete.” Mater. Struct. 40 (9): 981–988. https://doi.org/10.1617/s11527-006-9192-y.
Poon, C. S., and C. S. Lam. 2008. “The effect of aggregate-to-cement ratio and types of aggregates on the properties of pre-cast concrete blocks.” Cem. Concr. Compos. 30 (4): 283–289. https://doi.org/10.1016/j.cemconcomp.2007.10.005.
Poon, C. S., Z. H. Shui, and L. Lam. 2004a. “Effect of microstructure of ITZ on compressive strength of concrete prepared with recycled aggregates.” Constr. Build. Mater. 18 (6): 461–468. https://doi.org/10.1016/j.conbuildmat.2004.03.005.
Poon, C. S., Z. H. Shui, L. Lam, H. Fok, and S. C. Kou. 2004b. “Influence of moisture states of natural and recycled aggregates on the slump and compressive strength of concrete.” Cem. Concr. Res. 34 (1): 31–36. https://doi.org/10.1016/S0008-8846(03)00186-8.
Purushothaman, R., R. R. Amirthavalli, and L. Karan. 2014. “Influence of treatment methods on the strength and performance characteristics of recycled aggregate concrete.” J. Mater. Civ. Eng. 27 (5): 04014168. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001128.
Radonjanin, V., M. Malešev, and S. Marinković. 2010. “Recycled concrete as aggregate for structural concrete production.” Sustainability 2 (5): 1204–1225. https://doi.org/10.3390/su2051204.
Rahal, K. 2007. “Mechanical properties of concrete with recycled coarse aggregate.” Build. Environ. 42 (1): 407–415. https://doi.org/10.1016/j.buildenv.2005.07.033.
Rao, M. C., and K. Arun. 2015. “Influence of superplasticizer on properties of recycled aggregate concrete.” Asian J. Civ. Eng. 16 (7): 1001–1023.
Rao, M. C., S. K. Bhattacharyya, and S. V. Barai. 2011. “Influence of field recycled coarse aggregate on properties of concrete.” Mater. Struct. 44 (1): 205–220. https://doi.org/10.1617/s11527-010-9620-x.
Ravindrarajah, R. S., Y. H. Loo, and C. T. Tam. 1987. “Recycled concrete as fine and coarse aggregates in concrete.” Mag. Concr. Res. 39 (141): 214–220. https://doi.org/10.1680/macr.1987.39.141.214.
Ravindrarajah, R. S., and C. T. Tam. 1985. “Properties of concrete made with crushed concrete as coarse aggregate.” Mag. Concr. Res. 37 (130): 29–38. https://doi.org/10.1680/macr.1985.37.130.29.
Ridzuan, A. R. M., A. B. M. Diah, R. Hamir, and K. B. Kamarulzaman. 2001. “The influence of recycled aggregate on the early compressive strength and drying shrinkage of concrete.” In Proc., Int. Conf. on Structural Engineering, Mechanics and Computation, 2–4. Amsterdam, Netherlands: Elsevier.
Ryu, J. S. 2002. “Improvement on strength and impermeability of recycled concrete made from crushed concrete coarse aggregate.” J. Mater. Sci. Lett. 21 (20): 1565–1567. https://doi.org/10.1023/A:1020349011716.
Safiuddin, M., U. J. Alengaram, M. M. Rahman, M. A. Salam, and M. Z. Jumaat. 2013. “Use of recycled concrete aggregate in concrete: A review.” J. Civ. Eng. Manage. 19 (6): 796–810. https://doi.org/10.3846/13923730.2013.799093.
Sagoe-Crentsil, K. K., T. Brown, and A. H. Taylor. 2001. “Performance of concrete made with commercially produced coarse recycled concrete aggregate.” Cem. Concr. Res. 31 (5): 707–712. https://doi.org/10.1016/S0008-8846(00)00476-2.
Sahoo, K. K., M. Arakha, P. Sarkar, R. Davis, and S. Jha. 2016. “Enhancement of properties of recycled coarse aggregate concrete using bacteria.” Int. J. Smart Nano Mater. 7 (1): 22–38. https://doi.org/10.1080/19475411.2016.1152322.
Saravanakumar, P., and G. Dhinakaran. 2013. “Strength characteristics of high-volume fly ash-based recycled aggregate concrete.” J. Mater. Civ. Eng. 25 (8): 1127–1133. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000645.
Sato, R., I. Maruyama, T. Sogabe, and M. Sogo. 2007. “Flexural behavior of reinforced recycled concrete beams.” J. Adv. Concr. Technol. 5 (1): 43–61. https://doi.org/10.3151/jact.5.43.
Sheen, Y. N., H. Y. Wang, Y. P. Juang, and D. H. Le. 2013. “Assessment on the engineering properties of ready-mixed concrete using recycled aggregates.” Constr. Build. Mater. 45: 298–305. https://doi.org/10.1016/j.conbuildmat.2013.03.072.
Silva, R. V., J. de Brito, and R. K. Dhir. 2014. “The influence of the use of recycled aggregates on the compressive strength of concrete: a review.” Eur. J. Environ. Civ. Eng. 19 (7): 825–849. https://doi.org/10.1080/19648189.2014.974831.
Simeonov, P., and S. Ahmad. 1995. “Effect of transition zone on the elastic behavior of cement-based composites.” Cem. Concr. Res. 25 (1): 165–176. https://doi.org/10.1016/0008-8846(94)00124-H.
Sivakumar, N., S. Muthukumar, V. Sivakumar, D. Gowtham, and V. Muthuraj. 2014. “Experimental studies on high strength concrete by using recycled coarse aggregate.” Int. J. Eng. Sci. 4 (1): 27–36.
Somna, R., C. Jaturapitakkul, W. Chalee, and P. Rattanachu. 2012. “Effect of the water to binder ratio and ground fly ash on properties of recycled aggregate concrete.” J. Mater. Civ. Eng. 24 (1): 16–22. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000360.
Sriravindrarajah, R., N. D. H. Wang, and L. J. W. Ervin. 2012. “Mix design for pervious recycled aggregate concrete.” Int. J. Concr. Struct. Mater. 6 (4): 239–246. https://doi.org/10.1007/s40069-012-0024-x.
Srivastava, V., R. Kumar, and P. K. Mehta. 2013. “Concrete made with waste materials—A review.” J. Environ. Nanotechnol. 2 (2): 102–106. https://doi.org/10.13074/jent.2013.06.132022.
Tabsh, S. W., and A. S. Abdelfatah. 2009. “Influence of recycled concrete aggregates on strength properties of concrete.” Constr. Build. Mater. 23 (2): 1163–1167. https://doi.org/10.1016/j.conbuildmat.2008.06.007.
Tam, V. W., A. Butera, and K. N. Le. 2016. “Carbon-conditioned recycled aggregate in concrete production.” J. Cleaner Prod. 133: 672–680. https://doi.org/10.1016/j.jclepro.2016.06.007.
Tam, V. W., X. F. Gao, and C. M. Tam. 2005. “Microstructural analysis of recycled aggregate concrete produced from two-stage mixing approach.” Cem. Concr. Res. 35 (6): 1195–1203. https://doi.org/10.1016/j.cemconres.2004.10.025.
Tam, V. W., and C. M. Tam. 2008. “Diversifying two-stage mixing approach (TSMA) for recycled aggregate concrete: and .” Constr. Build. Mater. 22 (10): 2068–2077. https://doi.org/10.1016/j.conbuildmat.2007.07.024.
Tam, V. W., C. M. Tam, and K. N. Le. 2007a. “Removal of cement mortar remains from recycled aggregate using pre-soaking approaches.” Resour. Conserv. Recycl. 50 (1): 82–101. https://doi.org/10.1016/j.resconrec.2006.05.012.
Tam, V. W., C. M. Tam, and Y. Wang. 2007b. “Optimization on proportion for recycled aggregate in concrete using two-stage mixing approach.” Constr. Build. Mater. 21 (10): 1928–1939. https://doi.org/10.1016/j.conbuildmat.2006.05.040.
Tavakoli, M., and P. Soroushian. 1996. “Strengths of recycled aggregate concrete made using field-demolished concrete as aggregate.” ACI Mater. J. 93 (2): 178–181.
Tazawa, E., T. Kasai, and S. Okamoto. 1989. “Compressive strength of concrete prepared by double mixing.” J. Mater. Concr. Struct. Pavements 408: 139–146.
Thomas, C., J. Setién, J. A. Polanco, P. Alaejos, and M. S. de Juan. 2013. “Durability of recycled aggregate concrete.” Constr. Build. Mater. 40: 1054–1065. https://doi.org/10.1016/j.conbuildmat.2012.11.106.
Thomas, C., I. Sosa, J. Setién, J. A. Polanco, and A. I. Cimentada. 2014. “Evaluation of the fatigue behavior of recycled aggregate concrete.” J. Cleaner Prod. 65: 397–405. https://doi.org/10.1016/j.jclepro.2013.09.036.
Topcu, I. B. 1997. “Physical and mechanical properties of concretes produced with waste concrete.” Cem. Concr. Res. 27 (12): 1817–1823.
Topcu, I. B., and N. Güncan. 1995. “Using waste concrete as aggregate.” Cem. Concr. Res. 25 (7): 1385–1390.
Torgal, F. P., and S. Jalali. 2011. “Construction and demolition (C&D) wastes.” In Eco-efficient construction and building materials, 51–73. London: Springer.
Ulloa, V. A., E. García-Taengua, M. J. Pelufo, A. Domingo, and P. Serna. 2013. “New views on effect of recycled aggregates on concrete compressive strength.” ACI Mater. J. 110 (6): 687–696.
Vilardell, J., A. Aguado, L. Agullo, and R. Gettu. 1998. “Estimation of the modulus of elasticity for dam concrete.” Cem. Concr. Res. 28 (1): 93–101. https://doi.org/10.1016/S0008-8846(97)00214-7.
Wagih, A. M., H. Z. El-Karmoty, M. Ebid, and S. H. Okba. 2013. “Recycled construction and demolition concrete waste as aggregate for structural concrete.” HBRC J. 9 (3): 193–200. https://doi.org/10.1016/j.hbrcj.2013.08.007.
Wang, H. L., J. J. Wang, X. Y. Sun, and W. L. Jin. 2013. “Improving performance of recycled aggregate concrete with superfine pozzolanic powders.” J. Cent. South Univ. 20 (12): 3715–3722. https://doi.org/10.1007/s11771-013-1899-7.
Wang, Z., L. Wang, Z. Cui, and M. Zhou. 2011. “Effect of recycled coarse aggregate on concrete compressive strength.” Trans. Tianjin Univ. 17 (3): 229–234. https://doi.org/10.1007/s12209-011-1499-2.
Wang, Z. W. 2007. “Production and properties of high quality recycled aggregates.” Concrete 3: 74–77.
Wardeh, G., E. Ghorbel, and H. Gomart. 2014. “Mix design and properties of recycled aggregate concretes: Applicability of Eurocode 2.” Int. J. Concr. Struct. Mater. 9 (1): 1–20. https://doi.org/10.1007/s40069-014-0087-y.
Wei, X. 2006. “Experimental study on influence of recycled coarse aggregates contents on properties of recycled aggregate concrete.” Concrete 10: 45–47.
Wu, K. R., B. Chen, W. Yao, and D. Zhang. 2001. “Effect of coarse aggregate type on mechanical properties of high-performance concrete.” Cem. Concr. Res. 31 (10): 1421–1425. https://doi.org/10.1016/S0008-8846(01)00588-9.
Xiao, J., H. Li, and Z. Yang. 2013. “Fatigue behavior of recycled aggregate concrete under compression and bending cyclic loadings.” Constr. Build. Mater. 38: 681–688. https://doi.org/10.1016/j.conbuildmat.2012.09.024.
Xiao, J., J. Li, and C. Zhang. 2005. “Mechanical properties of recycled aggregate concrete under uniaxial loading.” Cem. Concr. Res. 35 (6): 1187–1194. https://doi.org/10.1016/j.cemconres.2004.09.020.
Xiao, J., P. Li, and W. Qin. 2006a. “Study on bond-slip between recycled concrete and rebars.” J.-Tongji Univ. 34 (1): 13.
Xiao, J., W. Li, Y. Fan, and X. Huang. 2012a. “An overview of study on recycled aggregate concrete in China (1996–2011).” Constr. Build. Mater. 31: 364–383. https://doi.org/10.1016/j.conbuildmat.2011.12.074.
Xiao, J., W. Li, and C. Poon. 2012b. “Recent studies on mechanical properties of recycled aggregate concrete in China—A review.” Sci. China Technol. Sci. 55 (6): 1463–1480. https://doi.org/10.1007/s11431-012-4786-9.
Xiao, J., M. Tawana, and X. Huang. 2012c. “Review of studies on structural performance of recycled aggregate concrete in China.” Sci. China Technol. Sci. 55 (10): 2727–2739. https://doi.org/10.1007/s11431-012-4803-z.
Xiao, J. Z., J. B. Li, and C. Zhang. 2006b. “On relationships between the mechanical properties of recycled aggregate concrete: an overview.” Mater. Struct. 39 (6): 655–664. https://doi.org/10.1617/s11527-006-9093-0.
Yang, K. H., H. S. Chung, and A. F. Ashour. 2008. “Influence of type and replacement level of recycled aggregates on concrete properties.” ACI Mater. J 105 (3): 289–296.
Yang, X., J. Wu, and J. G. Liang. 2009. “Experimental study on relationship between tensile strength and compressive strength of recycled aggregate concrete.” Sichuan Build. Sci. 35: 190–192.
Ye, H. 2009. “Experimental study on mechanical properties of concrete made with high quality recycled aggregate.” Sichuan Build. Sci. 35: 195–199.
Yoda, K., T. Yoshikane, Y. Nakashima, and T. Soshiroda. 1988. “Recycled cement and recycled concrete in Japan.” In Proc., Int. Conf. on Demolition and Reuse of Concrete and Masonry, 527–536. Boca Raton, FL: CRC Press.
Younis, K. H., and K. Pilakoutas. 2013. “Strength prediction model and methods for improving recycled aggregate concrete.” Constr. Build. Mater. 49: 688–701. https://doi.org/10.1016/j.conbuildmat.2013.09.003.
Zaetang, Y., V. Sata, A. Wongsa, and P. Chindaprasirt. 2016. “Properties of previous concrete containing recycled concrete block aggregate and recycled concrete aggregate.” Constr. Build. Mater. 111: 15–21. https://doi.org/10.1016/j.conbuildmat.2016.02.060.
Zega, C. J., and A. A. Di Maio. 2011a. “Recycled concretes made with waste ready-mix concrete as coarse aggregate.” J. Mater. Civ. Eng. 23 (3): 281–286. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000165.
Zega, C. J., and A. A. Di Maio. 2011b. “Use of recycled fine aggregate in concretes with durable requirements.” Waste Manage. 31 (11): 2336–2340. https://doi.org/10.1016/j.wasman.2011.06.011.
Zhao, H., B. K. Liu, and L. U. Guo 2008. “Experimental research on the basic mechanical properties of recycled aggregate concrete.” J. Anhui Inst. Archit. Ind. 6: 3.
Zhao, Z., S. Wang, L. Lu, and C. Gong. 2013. “Evaluation of pre-coated recycled aggregate for concrete and mortar.” Constr. Build. Mater. 43: 191–196. https://doi.org/10.1016/j.conbuildmat.2013.01.032.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 30 • Issue 9 • September 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jul 13, 2017
Accepted: Dec 6, 2017
Published online: Jun 27, 2018
Published in print: Sep 1, 2018
Discussion open until: Nov 27, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.