Effects of Different Aging Methods on Chemical and Rheological Properties of Bitumen
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 3
Abstract
Bitumen undergoes ageing, which leads to changes in its chemical and rheological properties, causing it to become harder and more brittle with time. This study aims to compare the effects of different laboratory ageing methods on the chemistry and rheology of three bitumen types: a Pen , a Pen , and a polymer-modified bitumen (PmB). Four ageing protocols were applied: ageing at room temperature, oven ageing, pressure ageing vessel (PAV), and rolling thin-film oven test (RTFOT) combined with PAV ageing. The effects of temperature, pressure, and ageing time were studied using dynamic shear tests and infrared spectroscopy. The results highlight the relationship between chemistry and rheology of bitumen. Bitumen hardening, which was revealed by an increase in complex modulus and a decrease in phase angle, was reflected in the growth of specific chemical functional groups. Among all materials, soft bitumen showed the greater tendency to oxidize. Different behavior was observed for PmB, which presented the highest resistance against oxidation among the studied bitumens, even though the reaction with oxygen caused the deterioration of the added polymer modifiers.
Get full access to this article
View all available purchase options and get full access to this article.
References
BRRC (Belgian Road Research Centre). (2013). “Method of measurement ME 85/13: Bitumen analysis by FTIR spectrometry: Testing and analysis protocol.” ME 85/13, Brussels, Belgium.
CEN (European Committee for Standardization). (2005). “Bitumen and bituminous binders—Accelerated long-term ageing conditioning by a pressure ageing vessel (PAV).” NEN-EN 14769, Brussels, Belgium.
CEN (European Committee for Standardization). (2014a). “Bitumen and bituminous binders. Determination of the resistance to hardening under influence of heat and air.” NEN-EN 12607-1, Brussels, Belgium.
CEN (European Committee for Standardization). (2014b). “Bitumen and bituminous binders. Preparation of test samples.” NEN-EN 12594, Brussels, Belgium.
Corbett, L. W. (1969). “Composition of asphalt based on generic fractionation, using solvent deasphaltening, elution-adsorption chromatography and densimetric characterization.” Anal. Chem., 41(4), 576–579.
Dondi, G., Mazzotta, F., Simone, A., Vignali, V., Sangiorgi, C., and Lantieri, C. (2016). “Evaluation of different short term aging procedures with neat, warm and modified binders.” J. Constr. Build. Mater., 106, 282–289.
Dondi, G., Vignali, V., Pettinari, M., Mazzotta, F., Simone, A., and Sangiorgi, C. (2014). “Modeling the DSR complex shear modulus of asphalt binder using 3D discrete element approach.” J. Constr. Build. Mater., 54, 236–246.
Herrington, P. R. (2012). “Diffusion and reaction of oxygen in bitumen films.” J. Fuel, 94(1), 86–92.
Juristyarini, P., Davison, R., and Glover, C. J. (2011). “Development of an asphalt aging procedure to assess long-term binder performance.” J. Pet. Sci. Technol., 29(21), 2258–2268.
Karlsson, R., and Isacsson, U. (2003). “Laboratory studies of diffusion in bitumen using markers.” J. Mater. Sci., 38(13), 2835–2844.
Lamontagne, J., Dumas, P., Mouillet, V., and Kister, J. (2001). “Comparison by Fourier transform infrared (FTIR) spectrocopy of different ageing techniques: Application to road bitumen.” J. Fuel, 80(4), 483–488.
Lerfald, B. O. (2000). “Ageing and degradation of asphalt pavements on low volume roads.” Ph.D. thesis, Norwegian Univ. of Science and Technology, Trondheim, Norway.
Lesueur, D. (2009). “The colloidal structure of bitumen: Consequences on the rheology and on the mechanisms of bitumen modification.” J. Adv. Colloid Interface Sci., 145(1–2), 42–82.
Liu, M., Lunsford, K. M., Davison, R. R., Glover, C. J., and Bullin, J. A. (1996). “The kinetics of carbonyl formation in asphalt.” AIChE J., 42(4), 1069–1076.
Lopes, M. D. M., Zhao, D., Chailleux, E., Kane, M., Gabet, T., and Petiteau, C. (2012). “Characterization of aging processes on the asphalt mixture surface.” Proc., 2nd Int. Symp. on Asphalt Pavements et Environnement, Transportation Research Board, The National Academies, Washington, DC.
Lu, X., Talon, Y., and Redelius, P. (2008). “Aging of bituminous binders– Laboratory tests and field data.” Proc., 4th Eurasphalt and Eurobitumen Congress, European Asphalt Pavement Association, Brussels, Belgium.
Mazzotta, F., Sangiorgi, C., Vignali, V., Lantieri, C., and Dondi, G. (2016). “Rheological characterization of bituminous mastics containing waste bleaching clays.” Proc., 8th RILEM Int. Symp. on Testing and Characterization of Sustainable and Innovative Bituminous Materials, Vol. 11, Springer, Berlin, 595–606.
Molenaar, A. A. A., Hagos, E. T., and van de Ven, F. C. (2010). “Effects of aging on the mechanical characteristics of bituminous binders in PAC.” J. Mater. Civ. Eng., 779–787.
Nivitha, M. R., Prasad, E., and Krishnan, J. M. (2015). “Ageing in modified bitumen using FTIR spectroscopy.” Int. J. Pavement Eng., 17(7), 565–577.
Petersen, J. C. (2009). “A review of the fundamentals of asphalt oxidation—Chemical, physicochemical, physical property, and durability relationship.”, Transportation Research Board, Washington, DC.
Redelius, P., and Soenen, H. (2015). “Relation between bitumen chemistry and performance.” J. Fuel, 140, 34–43.
Sangiorgi, C., Tataranni, P., Simone, A., Vignali, V., Lantieri, C., and Dondi, G. (2016). “Assessment of waste bleaching clay as alternative filler for the production of porous asphalts.” J. Constr. Build. Mater., 109, 1–7.
Van der Bergh, W. (2011). “The effect of ageing on the fatigue and healing properties of bituminous mortars.” Ph.D. thesis, Industrieel Ingenieur Bouwkunde, Hogeschool Antwerpen, Antwerpen, Belgium.
Vignali, V., Mazzotta, F., Sangiorgi, C., Simone, A., Lantieri, C., and Dondi, G. (2014). “Rheological and 3D DEM characterization of potential rutting of cold bituminous mastics.” J. Constr. Build. Mater., 73, 339–349.
Vignali, V., Mazzotta, F., Sangiorgi, C., Simone, A., Lantieri, C., and Dondi, G. (2016). “Incorporation of rubber powder as filler in a new dry-hybrid technology: Rheological and 3D DEM mastic performances evaluation.” J. Mater., 9(10), 842–861.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Apr 6, 2017
Accepted: Sep 19, 2017
Published online: Jan 6, 2018
Published in print: Mar 1, 2018
Discussion open until: Jun 6, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.