Viscosity-Based Complex Modulus and Phase-Angle Predictive Models for the Superpave Asphalt Mixtures of New Mexico
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 3
Abstract
The recently developed mechanistic-empirical design method of pavement uses the nationally calibrated dynamic modulus predictive model for the design and analysis of asphalt pavements. This study calibrates this model for the local Superpave asphalt concrete mixtures of New Mexico. Although the calibrated model shows good correlation, this study develops a new regression-based model which shows improved correlation with the tested data. A total of 54 asphalt-aggregate mixtures are compacted, cored, and sawed to cylindrical specimens and tested for dynamic modulus and phase angle. The time-temperature superposition principle is applied to develop master curves at a reference temperature of 70°F (21.1°C). The master curve parameters are correlated with the aggregate and binder properties. The local predictive models are validated for the dynamic modulus and phase angle of other AC mixtures which were not used to develop the models. Statistical evaluation shows that fairly accurate estimations of dynamic modulus and phase angle of the local mixes are possible by using these local predictive models.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors acknowledge the contributions of New Mexico Department of Transportation (NMDOT) and the Federal Highway Administration (FHWA) for providing funds for this research.
References
AASHTO. (2008). Mechanistic-empirical pavement design guide. A manual of practice, Interim Ed., Washington, DC.
AASHTO. (2011a). “Standard method of test for determining dynamic modulus of hot-mix asphalt concrete mixtures.” AASHTO T342, Washington, DC.
AASHTO. (2011b). “Standard method of test for preparing and determining the density of asphalt mixture specimens by means of the Superpave gyratory compactor.” AASHTO T312, Washington, DC.
AASHTO. (2011c). “Standard specification for Superpave volumetric mix design.” AASHTO MP2, Washington, DC.
AASHTO. (2012). “Standard method of test for theoretical maximum specific gravity () and density of hot-mix asphalt (HMA).” AASHTO T209, Washington, DC.
AASHTO. (2013). “Standard method of test for bulk specific gravity () of compacted hot-mix asphalt (HMA) using saturated surface-dry specimens.” AASHTO T166, Washington, DC.
AASHTOWare Pavement Design ME [Computer software]. AASHTOWare, Washington, DC.
Ahmed, M., Rahman, A., Islam, M. R., and Tarefder, R. A. (2015). “Combined effect of asphalt concrete cross-anisotropy and temperature variation on pavement stress-strain under dynamic loading.” Constr. Build. Mater., 93, 685–694.
Andrei, D., Witczak, M. W., and Mirza, M. W. (1999). “Development of a revised predictive model for the dynamic (complex) modulus of asphalt mixtures.”, Univ. of Maryland, College Park, MD.
ASTM. (1998). “Viscosity-temperature chart for asphalts.” ASTM D2493, West Conshohocken, PA, 230–234.
Birgisson, B., Sholar, G., and Roque, R. (2005). “Evaluation of predicted dynamic modulus for Florida mixtures.” Transp. Res. Rec., 1929, 200–207.
Christensen, D. W., Pellinen, T. K., and Bonaquist, R. F. (2003). “Hirsch model for estimating the modulus of asphalt concrete.” J. Assoc. Asphalt Paving Technol., 72, 97–121.
Clyne, T. R., Li, X., Marasteanu, M. O., and Skok, E. L. (2003). “Dynamic and resilient modulus of Mn/DOT asphalt mixtures.”, Minnesota Dept. of Transportation, St. Paul, MN.
Dongré, R., Myers, L., D’Angelo, J., Paugh, C., and Gudimettla, J. (2005). “Field evaluation of Witczak and Hirsch models for predicting dynamic modulus of hot-mix asphalt.” J. Assoc. Asphalt Paving Technol., 74, 381–442.
Kim, Y. R., King, M., and Momen, M. (2005). “Typical dynamic moduli values of hot mix asphalt in North Carolina and their prediction.” Proc., 84th Annual Meeting of the Transportation Research Board, Washington, DC.
MATLAB [Computer software]. MathWorks, Natick, MA.
Meyers, M. A., and Chawla, K. K. (1999). Mechanical behavior of materials, Prentice Hall, Upper Saddle River, NJ.
Mohammad, L. N., Wu, Z., Myers, L., Cooper, S., and Abadie, C. (2005). “A practical look at simple performance tests: Louisiana’s experience.” J. Assoc. Asphalt Paving Technol., 74, 557–600.
NCHRP (National Cooperative Highway Research Program). (2004). “Guide for mechanistic-empirical design of new-rehabilitated pavement structures.”, Washington, DC.
Rahman, A. S. M. A., Islam, M. R., and Tarefder, R. A. (2016). “Modifying the viscosity based Witczak model and developing phase angle predictive model for New Mexico’s Superpave mixes.” Proc., 95th Annual Meeting of the Transportation Research Board, Washington, DC.
Schwartz, C. W. (2005). “Evaluation of the Witczak dynamic modulus prediction model.” Proc., 84th Annual Meeting of the Transportation Research Board, Washington, DC.
Tarefder, R. A., and Rahman, A. S. M. A. (2016). “Enhanced statewide and independent assurance testing for dynamic modulus of NMDOT Superpave mixes for the implementation of mechanistic empirical pavement design guide.”, New Mexico Dept. of Transportation, Albuquerque, NM.
Tran, N. H., and Hall, K. D. (2005). “Evaluating the predictive equation in determining dynamic moduli of typical asphalt mixtures used in Arkansas.” J. Assoc. Asphalt Paving Technol., 74, 1–17.
Weldegiorgis, M. (2014). “On dynamic modulus of asphalt concrete for moisture damage.” Ph.D. dissertation, Univ. of New Mexico, Albuquerque, NM.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Dec 11, 2016
Accepted: Sep 13, 2017
Published online: Jan 11, 2018
Published in print: Mar 1, 2018
Discussion open until: Jun 11, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.