Optimum Rib Design in TMT Rebars to Enhance Fatigue Life While Retaining Bond Strength
Publication: Journal of Materials in Civil Engineering
Volume 30, Issue 3
Abstract
This paper investigates high-cycle fatigue (HCF) failure in thermomechanically treated (TMT) rebars using fractographic analysis. Most fatigue failures are found to initiate at the root of the transverse ribs, irrespective of rebar diameter. Three-dimensional finite-element (FE) analysis is used to study the effect of modifications to the rib geometry on stress concentrations at these critical locations. Modification of the ratio of the radius () of the root of the transverse rib to its height () is found to reduce stress concentrations at the rib root. A procedure combining FE analysis with ideas adapted from notch fatigue is developed to predict the fatigue life of rebars with optimum ratio. The predicted fatigue life of a 16-mm-diameter rebar with optimum ratio is found to be significantly higher than that of the original rebar. Pullout tests reveal that the proposed modification to the rib design does not result in any deterioration in bond strength between rebar and concrete.
Get full access to this article
View all available purchase options and get full access to this article.
References
ABAQUS version 6.9 [Computer software]. Simulia Corporation, Providence, RI.
Basu, P. C., Shylamoni, P., and Roshan, A. D. (2004). “Characterisation of steel reinforcement for RC structures: An overview and related issues.” Indian Concr. J., 19–30.
Baydoğan, M., Uysal, A., Kayalı, E. S., and Çimenoğlu, H. (2007). “Investigation on cyclic deformation behaviour of reinforced steel bars.” Advances in Fracture Research: Honour and Plenary Lectures Presented at 11th Int. Conf. on Fracture (ICF11), A. Carpinteri, Y.-W. Ma, and R. O. Ritchie, eds., Vol. 2, Springer, New York, 3920–3925.
BSI (British Standards Institution). (2005). “Steel for reinforcement of concrete—Weldable reinforcing steel—Bar, coil and decoiled product—Specification.” BS 4449, British Standards Institution, London.
Budynas, R. G., and Nisbett, J. K. (2011). Shigley’s mechanical engineering design, 9th Ed., McGraw-Hill, New York.
Burton, K. T. (1965). “Fatigue test on reinforcing bars.” J. Res. Dev. Lab., 7(3), 13–23.
Christian, J., Brown, C. J., Darwin, D., and McCabe, S. L. (1993). “Finite element fracture analysis of steel-concrete bond.”, Univ. of Kansas Center for Research, Lawrence, KS.
Deb, A., and Bhattacharya, S. (2010). “An investigation into the effect of bonding on FRP wrapped cylindrical concrete columns.” J. Compos. Constr., 706–719.
Det Norske Veritas. (2011). “Fatigue design of offshore steel structures, recommended practice.” DNV-RP-C203, Høvik, Norway.
Fei, J., and Darwin, D. (1999). “Fatigue of high relative rib area reinforcing bars.”, Univ. of Kansas Center for Research, Lawrence, KS.
Harkegard, G., and Halleraker, G. (2010). “Assessment of methods for prediction of notch and size effects at the fatigue limit based on test data by Bohm and Magin.” Int. J. Fatigue, 32(10), 1701–1709.
Helgason, T., Hanson, T. M., Somes, N. F., Corley, W. G., and Hognestad, E. (1976). “Fatigue strength of high yield reinforcing bars.”, National Research Council, Washington, DC.
Herwig, A. (2008). “Reinforced concrete bridges under increased railway traffic loads: Fatigue behaviour and safety measures.” Ph.D. thesis, Swiss Federal Institute of Technology in Lausanne, Lausanne, Switzerland.
IS (Indian Standard). (1959). “Methods of tests for strength of concrete.” IS 516, New Delhi, India.
IS (Indian Standard). (1967). “Methods of testing bond in reinforced concrete. Part I: Pull-out test.” IS: 2770, New Delhi, India.
IS (Indian Standard). (1999). “Splitting tensile strength of concrete method of test.” IS 5816, New Delhi, India.
IS (Indian Standard). (2005). “Metallic materials—Tensile testing at ambient temperature.” IS 1608, New Delhi, India.
IS (Indian Standard). (2008). “High strength deformed steel bars and wires for concrete reinforcement—Specification.” IS 1786, New Delhi, India.
Jhamb, I. C., and MacGregor, J. G. (1974a). “Effect of surface characteristics on the fatigue strength of reinforcing steel.” ACI Special Publication 41-7, Detroit, 139–168.
Jhamb, I. C., and MacGregor, J. G. (1974b). “Stress concentration caused by reinforcing bar deformation.” Abeles Symp. on Fatigue of Concrete (ACI SP 41), American Concrete Institute, Detroit, 169–182.
Kopas, P., Jakubovičová, L., Vaško, M., and Handrik, M. (2016). “Fatigue resistance of reinforcing steel bars.” Procedia Eng., 136, 193–197.
Lowes, L. N., Moehle, J. P., and Govindjee, S. (2004). “Concrete-steel bond model for use in finite element modeling of reinforced concrete structures.” ACI Struct. J., 101(4), 501–511.
MacGregor, J. G., Jhamb, I. C., and Nuttal, N. (1971). “Fatigue strength of hot rolled deformed reinforcing bars.” ACI J., 68(3), 169–179.
Pfister, J. F., and Hognestad, E. (1964). “High strength bars as concrete reinforcement. Part 6: Fatigue tests.” J. PCA Res. Dev. Lab., 6(1), 65–84.
Popovics, S. A. (1973). “Numerical approach to the complete stress-strain curve of concrete.” Cem. Concr. Res., 3(5), 583–599.
Ray, A., et al. (1997). “Microstructure and properties of thermomechanically strengthened reinforcement bars: A comparative assessment of plain-carbon and low-alloy steel grades.” J. Mater. Eng. Perform., 6(3), 335–343.
Rocha, M., Brühwiler, E., and Nussbaumer, A. (2016). “Geometrical and material characterization of quenched and self-tempered steel reinforcement bars.” J. Mater. Civ. Eng., 04016012.
Thandavamoorthy, T. S. (1999). “Static and fatigue of high ductility bars reinforced concrete beams.” J. Mater. Civ. Eng., 41–50.
Tilly, G. P. (1979). “Fatigue of steel reinforcement bars in concrete: A review.” Fatigue Eng. Mater. Struct., 2(3), 251–268.
Young, W. C., and Budynas, R. G. (2011). Roark’s formulas for stress and strain, 7th Ed., McGraw-Hill, New York.
Zheng, H., and Abel, A. (1998). “Stress concentration and fatigue of profiled reinforcing steels.” Int. J. Fatigue, 20(10), 767–773.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Feb 21, 2017
Accepted: Aug 28, 2017
Published online: Dec 29, 2017
Published in print: Mar 1, 2018
Discussion open until: May 29, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.