Optimized Fresh and Hardened Properties of Strain Hardening Cementitious Composites: Effect of Mineral Admixtures, Cementitious Composition, Size, and Type of Aggregates
Publication: Journal of Materials in Civil Engineering
Volume 29, Issue 10
Abstract
The present paper thoroughly investigates the effects of mix design with various water-to-binder (W/B) ratios, types of mineral admixture and types and sizes of local sands on the tensile ductility of engineered cementitious composites (ECC). White and red dune sands—denoted W and D, whereas their sieved forms are denoted SW and SD, respectively—were collected from the Arabian Desert, the second largest on the earth. Fly ash (FA) and ground granulated blast furnace slag (GGBFS) were separately used as mineral admixtures in the production of ECC. The development of ductility in ECC mixtures incorporating FA was found to reduce with curing time, whereas it was found to increase with GGBFS. An ECC mixture containing 62% GGBFS with W/B ratio of 0.35 has delivered the best fresh and hardened properties with strain capacity of 4.2% and tensile strength of 5.2 MPa at 28 days. Water sorptivity of fully cracked dune sand–based ECC mixtures was lower than that given by normal concrete. It is concluded that dune sand–based ECC mixtures have provided comparable results to the reference silica sand–based ECC mixtures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was funded by the National Plan for Science, Technology, and Innovation (MAARIFAH), King Abdulaziz City for Science and Technology, Kingdom of Saudi Arabia, Award Number 12-ADV2591-02.
References
ACI (American Concrete Institute). (1988). “Measurement of properties of fiber reinforced concrete.” ACI Mater. J., 85(6), 583–593.
ASTM. (2013). “Standard test method for measurement of rate of absorption of water by hydraulic-cement concretes.” ASTM C1585-13, West Conshohocken, PA.
ASTM. (2015). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” ASTM C618-15, West Conshohocken, PA.
ASTM. (2016). “Standard specification for slag cement for use in concrete and mortars.” ASTM C989/C989M-16e1, West Conshohocken, PA.
ASTM. (2017). “Standard specification for portland cement.” ASTM C150/C150M-17, West Conshohocken, PA.
Banthia, N., and Trottier, J. (1995). “Test methods for flexural toughness characterization of fiber reinforced concrete: Some concerns and a proposition.” ACI Mater. J., 92(1), 48–57.
Buyukozturk, O., Gunes, O., and Karaca, E. (2002). “Debonding problems in seismic retrofitting of RC beams using FRP composites.” Proc., 7th US National Conf. on Earthquake Engineering, Earthquake Engineering Research Institute, Boston.
Chen, W., and Brouwers, H. (2007). “The hydration of slag. I: Reaction models for alkali-activated slag.” J. Mater. Sci., 42(2), 428–443.
Fan, Y., Yin, S., Wen, Z., and Zhong, J. (1999). “Activation of fly ash and its effects on cement properties.” Cem. Concr. Res., 29(4), 467–472.
Kanda, T., and Li, V. C. (1999). “A new micromechanics design theory for pseudo-strain hardening cementitious composites.” J. Eng. Mech., 373–381.
Khan, M. I., Fares, G., and Mourad, S. (2016). “Optimized fresh and hardened properties of strain hardening cementitious composites: Effect of sand size and workability.” J. Mater. Civil Eng., 04016152.
Kim, Y. Y., Kim, J. S., Kim, H. S., Kim, J. K., and Ha, G. J. (2004). “Uniaxial tensile behavior of high ductile fiber reinforced mortar designed with ground granulated blast furnace slag.” Proc., KSCE Annual Conf., Vol. 2022, Korean Society of Civil Engineers, Seoul, 546–551.
Lepech, M. D., and Li, V. C. (2008). “Large-scale processing of engineered cementitious composites.” ACI Mater. J., 105(4), 358–366.
Li, V. C. (1998). “Engineered cementitious composites—Tailored composites through micromechanical modeling.” Fiber reinforced concrete: Present and the future, N. Banthia, A. Bentur, and A. Mufti, eds., Canadian Society for Civil Engineering, Montreal, 64–97.
Li, V. C. (2003). “On engineered cementitious composites (ECC)—A review of the material and its applications.” Adv. Concr. Technol., 1(3), 215–230.
Li, V. C., Chan, Y. W., and Wu, H. C. (1994). “Interface strengthening mechanisms in polymeric fiber reinforced cementitious composites.” Proc., Int. Symp. on Brittle Matrix Composites 4, A. M. Brandt, V. C. Li, and I. H. Marshall, eds., IKB and Woodhead Publication, Warsaw, Poland, 7–16.
Li, V. C., Wang, S., and Wu, C. (2001). “Tensile strain-hardening behavior of polyvinyl alcohol engineered cementitious composite (PVA-ECC).” ACI Mater. J., 98(6), 483–492.
Li, V. C., Wu, C., Wang, S., Ogawa, A., and Saito, T. (2002). “Interface tailoring for strain-hardening polyvinyl alcohol-engineered cementitious composite (PVA-ECC).” ACI Mater. J., 99(5), 463–472.
Li, V. C., and Wu, H. C. (1992). “Conditions for pseudo strain-hardening in fiber reinforced brittle matrix composites.” Appl. Mech. Rev., 45(8), 390–398.
Lim, I., Chern, J.-C., Liu, T., and Chan, Y.-W. (2012). “Effect of ground granulated blast furnace slag on mechanical behavior of PVA-ECC.” J. Mar. Sci. Technol., 20(3), 319–324.
Ma, H., Qian, S., Zhang, Z., Lin, Z., and Li, V. C. (2015). “Tailoring engineered cementitious composites with local ingredients.” Constr. Build. Mater., 101(Dec), 584–595.
Maalej, M., and Li, V. C. (1995). “Introduction of strain-hardening engineered cementitious composites in design of reinforced concrete flexural members for improved durability.” ACI Struct. J., 92(2), 167–176.
Malhotra, V. M., and Mehta, P. K. (1996). “Pozzolanic and cementitious materials.” Advances in concrete technology, Vol. 1, Gordon and Breach Science Publishers SA, Amsterdam, Netherlands.
Mechtcherine, V., and Schulze, J. (2006). “Testing the behavior of strain hardening cementitious composites in tension.” Proc., Int. RILEM Workshop on High Performance Fiber Reinforced Cementitious Composites in Structural Applications, G. Fischer and V. C. Li, eds., RILEM Publications SARL, Bagneux, France, 37–46.
Mehta, P. K. (1999). Advances in concrete technology, Concrete International, Krimpen aan den Ijssel, Netherlands, 69–76.
Mehta, P. K. (2009). “Structural concrete textbook on behaviour, design and performance.” Design of durable concrete structures, Vol. 3, 2nd Ed., International Federation for Structural Concrete, Lausanne, Switzerland.
Neville, A. M. (1995). Properties of concrete, 4th Ed., Longman Group Limited, London.
Richardson, I. G., Brough, A. R., Groves, G. W., and Dobson, C. M. (1994). “The characterization of hardened alkali-activated blast-furnace slag pastes and the nature of the calcium silicate hydrate (C-S-H) phase.” Cem. Concr. Res., 24(5), 813–829.
Şahmaran, M., Lachemi, M., Hossain, K. M. A., Ranade, R., and Li, V. C. (2009). “Influence of aggregate type and size on ductility and mechanical properties of engineered cementitious composites.” ACI Mater. J., 106(3), 308–316.
Şahmaran, M. S., and Li, V. C. (2009). “Influence of microcracking on water absorption and sorptivity of ECC.” Mater. Struct., 42(5), 593–603.
Şahmaran, M. S., Yücel, H. E., Demirhan, S., and Li, V. C. (2012). “Combined effect of aggregate and mineral admixtures on tensile ductility of engineered cementitious composites.” ACI Mater. J., 109(6), 627–638.
Shao, Y., and Shah, S. P. (1997). “Mechanical properties of PVA fiber reinforced cement composites fabricated by extrusion processing.” ACI Mater. J., 94(6), 555–564.
Sherir, M. A. A., Hossain, K. M. A., and Lachemi, L. (2015). “Structural performance of polymer fiber reinforced engineered cementitious composites subjected to static and fatigue flexural loading.” Polymers, 7(7), 1299–1330.
Siddique, R., and Khan, M. I. (2011). Supplementary cementing materials, Springer, Germany, Berlin.
Tjiptobroto, P., and Hansen, W. (1993). “Tensile strain hardening and multiple cracking in high-performance cement-based composites containing discontinuous fibers.” ACI Mater. J., 90(1), 16–25.
Tsivilis, S., Tsantilas, J., Kakali, G., Chaniotakis, E., and Sakellariou, A. (2003). “The permeability of portland limestone cement concrete.” Cem. Concr. Res., 33(9), 1465–1471.
Yang, E. H., Yang, Y., and Li, V. C. (2007). “Use of high volumes of fly ash to improve ECC mechanical properties and material greenness.” ACI Mater. J., 104(6), 303–311.
Zhu, Y., Yang, Y., and Yao, Y. (2012). “Use of slag to improve mechanical properties of engineered cementitious composites (ECCs) with high volumes of fly ash.” Constr. Build. Mater., 36(Nov), 1076–1081.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Mar 10, 2016
Accepted: Apr 13, 2017
Published online: Jul 8, 2017
Published in print: Oct 1, 2017
Discussion open until: Dec 8, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.