Optimization of Mix Design of Thermally Efficient Blocks Using the Process Parameter Approach
Publication: Journal of Materials in Civil Engineering
Volume 29, Issue 3
Abstract
The development of thermally efficient blocks as wall material to provide a reduction in the heating/cooling load of a building envelope has been investigated by a host of researchers. This paper focuses on the mix design of thermally efficient blocks by using a well-known optimization technique. The method is used to optimize the proportion of the raw materials, i.e., glass powder (GP), palm-oil fly ash (POFA), and oil-palm fibers (OPFs) to achieve minimal thermal conductivity values. Mix proportions were designed as per an orthogonal array with three factors and four levels. Experimental investigations, such as bulk density, water absorption, compressive strength, and thermal conductivity, were conducted. Effects on thermal conductivity caused by control factors were analyzed using signal-to-noise (S/N) ratios and analysis of variance (ANOVA) techniques. The analysis provides percentage contribution of individual control factors and the identification of significant parameters contributing to thermal performance. Furthermore, thermal conductivity values were estimated on the basis of the optimal performance levels of parameters. Last, for validation of the optimized results, experiments on thermal conductivity were conducted alongside the primary essential standard properties of density, water absorption, and compressive strength.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research paper is an outcome of the research being undertaken at Universiti Tun Hussein Onn Malaysia (UTHM). A special thanks to the Research, Innovation, Commercialization and Consultancy Management (ORICC) Office at UTHM for the administrative support provided and for the Research Grant Vote No. U204 sponsorship.
References
ASTM. (2012). “Standard practice for using a guarded-hot-plate apparatus or thin-heater apparatus in the single-sided mode.”, West Conshohocken, PA.
ASTM. (2014a). “Standard specification for nonloadbearing concrete masonry units.”, ASTM International, West Conshohocken, PA.
ASTM. (2014b). “Standard test methods for sampling and testing brick and structural clay tile.”, West Conshohocken, PA.
ASTM. (2015). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” ASTM C618, West Conshohocken, PA.
Awal, A. A., and Hussin, M. W. (1997). “The effectiveness of palm oil fuel ash in preventing expansion due to alkali-silica reaction.” Cem. Concr. Compos., 19(4), 367–372.
Awal, A. A., and Shehu, I. A. (2013). “Evaluation of heat of hydration of concrete containing high volume palm oil fuel ash.” Fuel, 105, 728–731.
Binici, H., Aksogan, O., Bodur, M. N., Akca, E., and Kapur, S. (2007). “Thermal isolation and mechanical properties of fibre reinforced mud bricks as wall materials.” Constr. Build. Mater., 21(4), 901–906.
British Standard Institution. (1985). “Specification for clay bricks.” BS 3921, London.
British Standard Institution. (1999). “Thermal performance of buildings—Calculation of energy use for heating—Residential buildings.” BS EN 832:2000, London.
Dyer, T. D., and Dhir, R. K. (2001). “Chemical reactions of glass cullet used as cement component.” J. Mater. Civ. Eng., 412–417.
Essabir, H., Boujmal, R., Bensalah, M. O., Rodrigue, D., Bouhfid, R., and el kacem Qaiss, A. (2016). “Mechanical and thermal properties of hybrid composites: Oil-palm fiber/clay reinforced high density polyethylene.” Mech. Mater., 98, 36–43.
Hoornweg, D., and Bhada-Tata, P. (2012). “What a waste: A global review of solid waste management.” Urban Dev. Ser. Knowl. Pap., 15, 1–98.
Jaturapitakkul, C., Tangpagasit, J., Songmue, S., and Kiattikomol, K. (2011). “Filler effect and pozzolanic reaction of ground palm oil fuel ash.” Constr. Build. Mater., 25(11), 4287–4293.
Khedari, J., Charoenvai, S., and Hirunlabh, J. (2003). “New insulating particleboards from durian peel and coconut coir.” Build. Environ., 38(3), 435–441.
Malaysian Standard. (1972). “Specifications for bricks and blocks of fired brick-earth clay or shale. Part 2: Metric units.” MS 76, Kuala Lumpur, Malaysia.
Mittal, V., and Sinha, S. (2016). “Effect of alkali treatment on the thermal properties of wheat straw fiber reinforced epoxy composites.” J. Compos. Mater., in press.
Pigeonneau, F., and Muller, S. (2013). “The impact of iron content in oxidation front in soda-lime silicate glasses: An experimental and comparative study.” J. Non-Cryst. Solids, 380, 86–94.
Ramli, M., and Dawood, E. T. (2010). “Effects of palm fiber on the mechanical properties of lightweight concrete crushed brick.” Am. J. Eng. Appl. Sci., 3(2), 489–493.
Ranjbar, N., Behnia, A., Alsubari, B., Birgani, P. M., and Jumaat, M. Z. (2016). “Durability and mechanical properties of self-compacting concrete incorporating palm oil fuel ash.” J. Cleaner Prod., 112, 723–730.
Shayan, A., and Xu, A. (2004). “Value-added utilisation of waste glass in concrete.” Cem. Concr. Res., 34(1), 81–89.
Shi, C., Wu, Y., Riefler, C., and Wang, H. (2005). “Characteristics and pozzolanic reactivity of glass powders.” Cem. Concr. Res., 35(5), 987–993.
Shi, C., Wu, Y., Shao, Y., and Riefler, C. (2004). “Alkali-aggregate reaction of concrete containing ground glass powder.” Proc., 12th Int. Conf. on AAR in Concrete, International Academic, San Bernardino, CA.
Taguchi, G., and Cariapa, V. (1993). Taguchi on robust technology development, ASME, New York.
Thomas, M. (2011). “The effect of supplementary cementing materials on alkali-silica reaction: A review.” Cem. Concr. Res., 41(12), 1224–1231.
Tuan, B. L. A., Hwang, C. L., Lin, K. L., Chen, Y. Y., and Young, M. P. (2013). “Development of lightweight aggregate from sewage sludge and waste glass powder for concrete.” Constr. Build. Mater., 47, 334–339.
Turanli, L., Bektas, F., and Monteiro, P. J. M. (2003). “Use of ground clay brick as a pozzolanic material to reduce the alkali–silica reaction.” Cem. Concr. Res., 33(10), 1539–1542.
UNDP (United Nation Development Programme). (2008). “2007/2008 human development report: Malaysia.” ⟨http://hdrstats.undp.org/countries/country_fact_sheets/cty_fs_MYS.html⟩ (Oct. 15, 2015).
Zanotto, E. D. (1991). “Surface crystallization kinetics in soda-lime-silica glasses.” J. Non-Cryst. Solids, 129(1), 183–190.
Information & Authors
Information
Published In
Copyright
©2016 American Society of Civil Engineers.
History
Received: Mar 9, 2016
Accepted: Aug 11, 2016
Published online: Oct 24, 2016
Published in print: Mar 1, 2017
Discussion open until: Mar 24, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.