Using the Surface Free Energy Method to Evaluate the Effects of Nanomaterial on the Fatigue Life of Hot Mix Asphalt
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 10
Abstract
Fatigue cracking is the main form of structural damage in hot mix asphalt (HMA) at moderate temperatures. The one of ways to reduce this type of distress is use of nanomaterials as additives in asphalt mixtures. In this study, the effects of using as an asphalt binder modifier on the fatigue life of asphalt mixtures are assessed by surface free energy (SFE) method and indirect tensile fatigue (ITF) test. The HMA mixtures containing 0, 3, and 6% of are plant prepared with two sources of aggregate (granite and limestone), and one type of asphalt binder with 85/100-penetration grade. The results showed that fatigue lives of mixtures containing were higher than the control mixtures. This is attributed to the fact that adding leads to decrease of the acid component of SFE and increase of the basic component in SFE of the asphalt binder that enhances the adhesion between asphalt binder and aggregate. Furthermore, the asphalt mixtures made with the modified asphalt binder showed greater fatigue life than the control mixtures because of improved cohesion energy and higher resistance to fatigue cracking in asphalt film.
Get full access to this article
View all available purchase options and get full access to this article.
References
Arabani, M., and Hamedi, G. H. (2010). “Using the surface free energy method to evaluate the effects of polymeric aggregate treatment on moisture damage in hot-mix asphalt.” J. Mater. Civ. Eng., 802–811.
Arabani, M., Roshani, H., and Hamedi, G. H. (2011). “Estimating moisture sensitivity of warm mix asphalt modified with zycosoil as an antistrip agent using surface free energy method.” J. Mater. Civ. Eng., 889–897.
Arambula Mercado, E. (2007). “Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes.” Texas A&M Univ., College Station, TX.
ASTM. (1973). “Standard test method for penetration of bituminous materials.” ASTM D5-73, West Conshohocken, PA.
ASTM. (1976). “Standard test method for softening point of bitumen (ring and ball apparatus).” ASTM D36-76, West Conshohocken, PA.
ASTM. (1978). “Standard test method for flash and fire points by cleveland open cup tester.” ASTM D92-78, West Conshohocken, PA.
ASTM. (1985). “Standard test method for kinematic viscosity of asphalts (bitumens).” ASTM D2171-07, West Conshohocken, PA.
ASTM. (2005). “Standard test method for soundness of aggregates by use of sodium sulfate or magnesium sulfate.” ASTM C88, West Conshohocken, PA.
ASTM. (2006a). “Standard test method for determining the percentage of fractured particles in coarse aggregate.” ASTM D5821, West Conshohocken, PA.
ASTM. (2006b). “Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles machine.” ASTM C131, West Conshohocken, PA.
ASTM. (2007). “Standard test method for ductility of bituminous materials.” ASTM D113-79, West Conshohocken, PA.
ASTM. (2010a). “Standard test method for flat particles, elongated particles, or flat and elongated particles in coarse aggregate.” ASTM D4791, West Conshohocken, PA.
ASTM. (2010b). “Standard test methods for specific gravity of soil solids by water pycnometer.” ASTM D854, West Conshohocken, PA.
ASTM. (2012a). “Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate.” ASTM C127, West Conshohocken, PA.
ASTM. (2012b). “Standard test method for density, relative density (specific gravity), and absorption of fine aggregate.” ASTM C128, West Conshohocken, PA.
ASTM. (2015). “Standard test method for Marshall stability and flow of asphalt mixtures.” ASTM D6927–15, West Conshohocken, PA.
Bahia, H. U., Hanson, D., Zeng, M., Zhai, H., Khatri, M., and Anderson, R. (2001). “Characterization of modified asphalt binders in superpave mix design.”, Transportation Research Board, Washington, DC.
Bhasin, A. (2007). “Development of methods to quantify bitumen-aggregate adhesion and loss of adhesion due to water.” Texas A&M Univ., College Station, TX.
CEN (European Committee for Standardization). (2012). “Test methods for hot mix asphalt—Part 24: Resistance to fatigue.” EN12697-24, British Standards Institution, London.
Chen, C. C., and Wang, C. C. (2006). “Crosslinking of cotton cellulose with succinic acid in the presence of titanium dioxide nano-catalyst under UV irradiation.” J. Sol-Gel Sci. Technol., 40(1), 31–38.
Cheng, D., Little, D., Lytton, R., and Holste, J. (2002). “Surface energy measurement of asphalt and its application to predicting fatigue and healing in asphalt mixtures.” Transp. Res. Rec., 1810, 44–53.
Good, R. J., and van Oss, C. J. (1992). “The modern theory of contact angles and the hydrogen bond components of surface energies.” Modern approaches to wettability, Springer, New York, 1–27.
Hamedi, G. H., and Moghadas Nejad, F. (2015). “Using energy parameters based on the surface free energy concept to evaluate the moisture susceptibility of hot mix asphalt.” Road Mater. Pavement Des., 16(2), 239–255.
Hamedi, G. H., Moghadas Nejad, F., and Oveisi, K. (2015a). “Estimating the moisture damage of asphalt mixture modified with nano zinc oxide.” Mater. Struct., 1–10.
Hamedi, G. H., Moghadas Nejad, F., and Oveisi, K. (2015b). “Investigating the effects of using nanomaterials on moisture damage of HMA.” Road Mater. Pavement Des., 16(3), 1–17.
Hefer, A. W., Bhasin, A., and Little, D. N. (2006). “Bitumen surface energy characterization using a contact angle approach.” J. Mater. Civ. Eng., 759–767.
Huang, Y., Bird, R. N., and Heidrich, O. (2007). “A review of the use of recycled solid waste materials in asphalt pavements.” Resour. Conserv. Recycl., 52(1), 58–73.
Karahancer, S. S., Kiristi, M., Terzi, S., Saltan, M., Oksuz, A. U., and Oksuz, L. (2014). “Performance evaluation of nano-modified asphalt concrete.” Constr. Build. Mater., 71, 283–288.
Little, D. N., Bhasin, A., and Hefer, A. (2006). “Using surface energy measurements to select materials for asphalt pavement.” Transportation Research Board, Washington, DC.
Masad, E., Castelo Branco, V., Little, D., and Lytton, R. (2006). “An improved method for the dynamic mechanical analysis of fatigue failure of sand asphalt mixtures.”, Federal Highway Administration, Texas Transportation Institute, Texas A&M Univ., TX.
Moghadas Nejad, F., Azarhoosh, A. R., Hamedi, G. H., and Azarhoosh, M. J. (2012a). “Influence of using nonmaterial to reduce the moisture susceptibility of hot mix asphalt.” Constr. Build. Mater., 31, 384–388.
Moghadas Nejad, F., Hamedi, G. H., and Azarhoosh, A. R. (2012b). “Use of surface free energy method to evaluate effect of hydrate lime on moisture damage in hot-mix asphalt.” J. Mater. Civ. Eng., 1119–1126.
Packham, D. (1996). “Work of adhesion: Contact angles and contact mechanics.” Int. J. Adhes. Adhes., 16(2), 121–128.
Roberts, F. L., Kandhal, P. S., Brown, E. R., Lee, D.-Y., and Kennedy, T. W. (1996). “Hot mix asphalt materials, mixture design and construction.” National Asphalt Pavement Association Research and Education Foundation, Lanham, MD.
Sengoz, B., and Topal, A. (2005). “Use of asphalt roofing shingle waste in HMA.” Constr. Build. Mater., 19(5), 337–346.
Shafabakhsh, G., Mirabdolazimi, S., and Sadeghnejad, M. (2014). “Evaluation the effect of nano-TiO 2 on the rutting and fatigue behavior of asphalt mixtures.” Constr. Build. Mater., 54, 566–571.
Tanzadeh, J., Vahedi, F., Kheiry, P. T., and Tanzadeh, R. (2013). “Laboratory study on the effect of nano TiO2 on rutting performance of asphalt pavements.” Manufacturing science and technology III, R. Sivakumar, ed., Trans Tech Publications, Dürnten, Switzerland, 990–994.
Wen, H. (2001). “Fatigue performance evaluation of WesTrack asphalt mixtures based on viscoelastic analysis of indirect tensile test.” Ph.D. thesis, NC State Univ., Raleigh, NC.
Yusoff, N. I. M., Breem, A. A. S., Alattug, H. N., Hamim, A., and Ahmad, J. (2014). “The effects of moisture susceptibility and ageing conditions on nano-silica/polymer-modified asphalt mixtures.” Constr. Build. Mater., 72, 139–147.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 28, 2015
Accepted: Feb 10, 2016
Published online: Apr 25, 2016
Discussion open until: Sep 25, 2016
Published in print: Oct 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.