Comparative Study of the Hydromechanical Behavior of Intact, Horizontally Jointed, and Vertically Jointed Rocks under Undrained Conditions
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 9
Abstract
This paper investigates the influence of the presence of a joint (vertically or horizontally oriented) on the hydromechanical behavior of sandstone under undrained triaxial conditions. A series of undrained triaxial experiments was performed on intact and horizontally and vertically jointed sandstone samples under different confining pressures and initial pore-water pressures. Joints in jointed samples were artificially created with rough and irregular surface profiles. An increase in pore-water pressure with increasing deviatoric stress was observed for all tests. Maximum induced pore-water pressure values were higher and occurred later in the jointed rock samples when compared to the intact samples at all confining pressures. This may be related to the efficiency of the response of the joint pore volume to loading when compared to that of the matrix pore volume. Moreover, the significance of new pore volume creation (by microcracking during failure) on sample pore-water pressure is dependent on the initial pore volume, which itself varies with the presence and size of joints regardless of orientation. Effective peak deviatoric stresses observed from the tests were consistently higher for the intact rock samples when compared to the jointed rock. This result suggests that the compressive strengths of intact and horizontally and vertically jointed rocks are not comparable when the joint is rough and the deformation is undrained. The origin of the influence of horizontal or vertical joints on rock strength may relate to the presence of edges on the rough joints, which act as stress intensification points and allow material failure under lower applied stress for the jointed samples than for the intact (homogeneous) samples.
Get full access to this article
View all available purchase options and get full access to this article.
References
Aldrich, M. J. (1969). “Pore pressure effects on Berea sandstone subjected to experimental deformation.” Geol. Soc. Am. Bull., 80(8), 1577–1586.
Barton, N. (1973). “Review of a new shear strength criterion for rock joints.” Eng. Geol., 7(4), 287–332.
Baud, P., Louis, L., David, C., Rawling, G. C., and Wong, T.-F. (2005). “Effects of bedding and foliation on mechanical anisotropy, damage evolution and failure mode.” Geol. Soc. London, 245(1), 223–249.
Chong, W. L., Haque, A., Ranjith, P. G., and Shahinuzzaman, A. (2013). “Modelling of intact and jointed mudstone samples under uniaxial and triaxial compression.” Arab. J. Geosci., 6(5), 1639–1646.
Clark, I. H. (2006). “Simulation of rock mass strength using ubiquitous joints.” Proc., 4th Int. FLAC Symp. Numerical Modeling in Geomechanics, R. Hart and P. Varona, eds., Itasca Consulting Group, Minneapolis.
Dai, S., and Labuz, J. (1997). “Damage and failure analysis of brittle materials by acoustic emission.” J. Mater. Civ. Eng., 200–205.
Dropek, R. K., Johnson, J. N., and Walsh, J. B. (1978). “The influence of pore pressure on the mechanical properties Kayenta sandstone.” J. Geophys. Res., 83(B6), 2817–2824.
Duda, M., and Renner, J. (2013). “The weakening effect of water on the brittle failure strength of sandstone.” Geophys. J. Int., 192(3), 1091–1108.
Dunn, D. E., LaFountain, L. J., and Jackson, R. E. (1973). “Porosity dependence and mechanism of brittle fracture in sandstone.” J. Geophys. Res., 78(14), 2403–2417.
Fredrich, J. T., Martin, J. W., and Clayton, R. B. (1995). “Induced pore pressure response during undrained deformation of tuff and sandstone.” Mech. Mater., 20(2), 95–104.
Goodman, R. E., and Ohnishi, Y. (1973). “Undrained shear testing of jointed rock.” Rock Mech., 5(3), 129–149.
Griffith, A. A. (1921). “The phenomena of rupture and flow in solids.” Philos. Trans. R. Soc. London, 221A(582–593), 163–198.
Gu, X., Seidel, J., and Haberfield, C. (2003). “Direct shear test of sandstone-concrete joints.” Int. J. Geomech., 21–33.
Halakatevakis, N., and Sofianos, A. I. (2010). “Strength of a blocky rock mass based on an extended plane of weakness theory.” Int. J. Rock Mech. Min. Sci., 47(4), 568–582.
Indraratna, B., and Jayanathan, M. (2005). “Measurement of pore water pressure of clay-infilled rock joints during triaxial shearing.” Geotechnique, 55(10), 759–764.
Ismail, I. A. H., and Murrell, S. A. F. (1976). “Dilatancy and the strength of rocks containing pore water under undrained conditions.” Geophys. J. Int., 44(1), 107–134.
Jade, S., and Sitharam, T. (2003). “Characterization of strength and deformation of jointed rock mass based on statistical analysis.” Int. J. Geomech., 43–54.
Jaeger, J. C., Cook, N. G. W., and Zimmerman, R. W. (2007). Fundamentals of rock mechanics, 4th Ed., Wiley-Blackwell, Oxford, U.K.
Kumar, D., and Das, S. K. (2005). “An experimental study of the parameters influencing ultimate bearing strength of weak floor strata using physical modeling.” Geotech. Geol. Eng., 23(1), 1–15.
Mas Ivars, D., et al. (2011). “The synthetic rock mass approach for jointed rock mass modelling.” Int. J. Rock Mech. Min. Sci., 48(2), 219–244.
Ord, A., Vardoulakis, I., and Kajewski, R. (1991). “Shear band formation in Gosford sandstone.” Int. J. Rock Mech. Min. Sci., 28(5), 397–409.
Pells, P. J. N. (1977). “Measurement of engineering properties of Hawkesbury sandstone.” Aust. Geomech. J., G5(1), 10–20.
Potyondy, D. O., and Cundall, P. A. (2004). “A bonded-particle model for rock.” Int. J. Rock Mech. Min. Sci., 41(8), 1329–1364.
Ramamurthy, T., and Arora, V. K. (1994). “Strength predictions for jointed rocks in confined and unconfined states.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 31(1), 9–22.
Ranjith, P. G., Fourar, M., Pong, S. F., Chian, W., and Haque, A. (2004). “Characterisation of fractured rocks under uniaxial loading states.” Int. J. Rock Mech. Min. Sci., 41(3), 361–366.
Ranjith, P. G., Jasinge, D., Song, J. Y., and Choi, S. K. (2008). “A study of the effect of strain rate and moisture content on mechanical properties of concrete: Use of acoustic emission.” Int. J. Mech. Mater., 40(6), 453–469.
Reviron, N., Reuschle, T., and Bernard, J.-D. (2009). “The brittle deformation regime of water-saturated siliceous sandstones.” Geophys. J. Int., 178(3), 1766–1778.
Rodríguez-Sastre, M. A., Gutiérrez-Claverol, M., and Torres-Alonso, M. (2008). “Relationship between cleavage orientation, uniaxial compressive strength and Young’s modulus for slates in NW Spain.” Bull. Eng. Geol. Environ., 67(2), 181–186.
Singh, M., Rao, K. S., and Ramamurthy, T. (2002). “Strength and deformational behaviour of a jointed rock mass.” Rock Mech. Rock Eng., 35(1), 45–64.
Sulem, J., and Ouffroukh, H. (2006). “Hydromechanical behaviour of Fontainebleau sandstone.” Rock Mech. Rock Eng., 39(3), 185–213.
Tien, Y. M., Lee, D. H., and Juang, C. H. (1990). “Strain, pore pressure and fatigue characteristics of sandstone under various load conditions.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 27(4), 283–289.
Tiwari, R., and Rao, K. (2007). “Response of an anisotropic rock mass under polyaxial stress state.” J. Mater. Civ. Eng., 393–403.
Tiwari, R. P., and Rao, K. S. (2004). “Physical modeling of a rock mass under a true triaxial stress state.” Int. J. Rock Mech. Min. Sci., 41(3), 433.
Vesga, L. F., Vallejo, L. E., and Lobo-Guerrero, S. (2008). “DEM analysis of the crack propagation in brittle clays under uniaxial compression tests.” Int. J. Numer. Anal. Method Gemech., 32(11), 1405–1415.
Wasantha, P., Ranjith, P., and Viete, D. (2014a). “Specimen slenderness and the influence of joint orientation on the uniaxial compressive strength of singly jointed rock.” J. Mater. Civ. Eng., 06014002.
Wasantha, P. L. P., Darlington, W. J., and Ranjith, P. G. (2013). “Characterization of mechanical behaviour of saturated sandstone using a newly developed triaxial apparatus.” Exp. Mech., 53(5), 871–882.
Wasantha, P. L. P., and Ranjith, P. G. (2014). “Water-weakening behavior of Hawkesbury sandstone in brittle regime.” Eng. Geol., 178, 91–101.
Wasantha, P. L. P., Ranjith, P. G., and Shao, S. S. (2014b). “Energy monitoring and analysis during deformation of bedded-sandstone: Use of acoustic emission.” Ultrasonics, 54(1), 217–226.
Wasantha, P. L. P., Ranjith, P. G., Xu, T., Zhao, J., and Yan, Y. L. (2014c). “A new parameter to describe the persistency of non-persistent joints.” Eng. Geol., 181, 71–77.
Xu, T., Ranjith, P. G., Wasantha, P. L. P., Zhao, J., Tang, C. A., and Zhu, W. C. (2013). “Influence of the geometry of partially-spanning joints on mechanical properties of rock in uniaxial compression.” Eng. Geol., 167, 134–147.
Yang, Z. Y., Chen, J. M., and Huang, T. H. (1998). “Effect of joint sets on the strength and deformation of rock mass models.” Int. J. Rock Mech. Min. Sci., 35(1), 75–84.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 28 • Issue 9 • September 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Sep 11, 2015
Accepted: Jan 11, 2016
Published online: Apr 13, 2016
Published in print: Sep 1, 2016
Discussion open until: Sep 13, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.