Statistical Characteristics of Ethylene Tetrafluoroethylene Foil’s Mechanical Properties and Its Partial Safety Factors
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 5
Abstract
This paper investigates the statistical characteristics of ethylene tetrafluoroethylene (ETFE) foils’ uniaxial and biaxial mechanical properties and suggests optimal partial safety factors of this material. Ten groups of uniaxial tensile tests and nine groups of biaxial tensile tests were performed. The test results indicated that two yield points of ETFE foils were more stable than the ultimate yield point, and then these two yield points were recommended as the reference points for single-layer pretensioned and cushion foil types. Moreover, a probabilistic limit state design method was adopted to calculate partial safety factors of ETFE foils. The statistical characteristics of an ETFE foil’s resistance and the partial safety factors of this material under three load effect combinations were determined. Reliability indexes were finally checked on the basis of the central point method and the Rackwitz–Fiessler method, whose results showed that the suggested partial safety factors could satisfy the target reliability index. These data offer a deeper understanding of ETFE foil mechanical properties and could be conveniently adopted in ETFE structural design.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Natural Science Foundation of China (51478333).
References
Ambroziak, A., and Kłosowski, P. (2014). “Mechanical properties for preliminary design of structures made from PVC coated fabric.” Constr. Build. Mater., 50, 74–81.
Antretter, F., Haupt, W., and Holm, A. (2008). “Thermal transfer through membrane cushions analyzed by computational fluid dynamics.” Proc., 8th Symp. on the Building Physics in the Nordic Countries, Carsten Rode, Copenhagen, Denmark.
ASCE. (2010). “Tensile membrane structure.”, Reston, VA.
Badalassi, M., Biolzi, L., Royer-Carfagni, G., and Salvatore, W. (2014). “Safety factors for the structural design of glass.” Constr. Build. Mater., 55, 114–127.
Barakat, S., Bani-Hani, K., and Taha, M. Q. (2004). “Multi-objective reliability-based optimization of prestressed concrete beams.” Struct. Saf., 26(3), 311–342.
Caspeele, R., and Taerwe, L. (2014). “Influence of concrete strength estimation on the structural safety assessment of existing structures.” Constr. Build. Mater., 62, 77–84.
Charbonneau, L., Polak, M. A., and Penlidis, A. (2014). “Mechanical properties of ETFE foils: Testing and modelling.” Constr. Build. Mater., 60, 63–72.
Ching, J., and Phoon, K. (2011). “A quantile-based approach for calibrating reliability-based partial factors.” Struct. Saf., 33(4–5), 275–285.
De Focatiis, D., and Gubler, L. (2013). “Uniaxial deformation and orientation of ethylene-tetrafluoroethylene films.” Polym. Test., 32(8), 1423–1435.
Forster, B., and Mollaert, M. (2004). European design guide for tensile surface structures, TensiNet, Brussels, Belgium.
Galliot, C., and Luchsinger, R. H. (2011). “Uniaxial and biaxial mechanical properties of ETFE foils.” Polym. Test., 30(4), 356–365.
GB (Chinese Standard). (1985). “Unified standard for the design of building structures.”, Beijing.
GB (Chinese Standard). (2006). “Plastics—Determination of tensile properties.”, Beijing.
GB (Chinese Standard). (2008). “Unified standard reliability design of engineering structures.”, Beijing.
Hirschmann, B., Oreski, G., and Pinter, G. (2014). “Thermo-mechanical characterisation of fluoropolymer films for concentrated solar thermal applications.” Sol. Energy Mater. Sol. Cells, 130, 615–622.
Hu, J. H., Chen, W. J., Luo, R. J., Zhao, B., and Sun, R. (2014a). “Uniaxial cyclic tensile mechanical properties of ethylene tetrafluoroethylene (ETFE) foils.” Constr. Build. Mater., 63, 311–319.
Hu, J. H., Chen, W. J., Zhao, B., and Song, H. (2014b). “Experimental studies on summer performance and feasibility of a BIPV/T ethylene tetrafluoroethylene (ETFE) cushion structure system.” Energy Build., 69, 394–406.
Hu, J. H., Chen, W. J., Zhao, B., and Wang, K. (2015). “Uniaxial tensile mechanical properties and model parameters determination of ethylene tetrafluoroethylene (ETFE) foils.” Constr. Build. Mater., 75, 200–207.
IASS (International Association for Shell and Spatial Structures). (1986). “Recommendations for the design of air supported structures.” Madrid, Spain.
ISO. (2012). “Plastics-determination of tensile properties.”, Switzerland.
JCSS (Joint Committee on Structural Safety). (2001). “Probabilistic model code.” Zurich.
Kawabata, M. (2007). “Viscoplastic properties of ETFE film and structural behavior of film cushion.” Proc., IASS Symp., International Association for Shell and Spatial Structures (IASS), Madrid, Spain.
Kawabata, M., and Moriyama, F. (2006). “Study on viscoelastic characteristics and structural response of film membrane structures.” Proc., IASS Symp., International Association for Shell and Spatial Structures (IASS), Madrid, Spain.
Kotera, S., and Yamaguchi, M. (2014). “Rheological characterization on thermal degradation of ethylene-tetrafluoroethylene copolymer.” J. Fluorine. Chem., 166, 117–121.
LeCuyer, A. (2008). ETFE technology and design, Birkhauser, Basel, Switzerland.
Li, Y. T., and Wu, M. E. (2015a). “Biaxial creep property of ethylene tetrafluoethylene (ETFE) foil.” Struct. Eng. Mech., 54(5), 973–986.
Li, Y. T., and Wu, M. E. (2015b). “Uniaxial creep property and viscoelastic-plastic modelling of ethylene tetrafluoethylene (ETFE) foil.” Mech. Time-Depend. Mater., 19(1), 21–34.
Liu, H., Polak, M. A., and Penlidis, A. (2008). “A practical approach to modeling time-dependent nonlinear creep behavior of polyethylene for structural applications.” Polym. Eng. Sci., 48(1), 159–167.
Mohamed, A., Soares, R., and Venturini, W. S. (2001). “Partial safety factors for homogeneous reliability of nonlinear reinforced concrete columns.” Struct. Saf., 23(2), 137–156.
Moritz, K. (2007). “Construction of the ETFE foil systems.” Stahlbau, 76(5), 336–342.
Moritz, K., and Hafner, A. (2010). “Transparency carried by air-pneumatic ETFE-foil cushion technology.” Proc., Structures Congress, ASCE, Reston, VA.
MSAJ (Membrane Structure Association of Japan). (2005). “Recommendations for design and construction of ETFE film panels (draft).” Tokyo.
Pimentel, M., Brühwiler, E., and Figueiras, J. (2014). “Safety examination of existing concrete structures using the global resistance safety factor concept.” Eng. Struct., 70, 130–143.
Robinson-Gayle, S., Kolokotroni, M., Cripps, A., and Tanno, S. (2001). “ETFE foil cushions in roofs and atria.” Constr. Build. Mater., 15(7), 323–327.
Wu, M. E., and Liu, J. M. (2008). “Experimental studies on ETFE cushion model.” Proc., IASS Symp., International Association for Shell and Spatial Structures (IASS), Madrid, Spain.
Wu, M. E., Wu, Y. Y., and Kim, J. Y. (2011). “ETFE foil spring cushion structure and its analytical method.” Thin. Wall. Struct., 49(9), 1184–1190.
Zhang, Y., Zhang, Q., Yang, Z., Chen, L., and Cao, Y. (2015). “Load-dependent mechanical behavior of membrane materials and its effect on the static behaviors of membrane structures.” J. Mater. Civ. Eng., 04015018.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Mar 10, 2015
Accepted: Aug 17, 2015
Published online: Jan 4, 2016
Published in print: May 1, 2016
Discussion open until: Jun 4, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.