Exposure of Mortars Modified with Rubber Aggregates and Polymer Admixtures to Acid Environments and Elevated Temperature Conditions
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 4
Abstract
The aim of the present paper was to study the effect of incorporating rubber aggregates and acrylic or EVA polymers on the properties of cement mortar exposed to acid (HCl, , ) and elevated temperature conditions. Compressive and bending strength tests, water absorption test, mass measurements, and visual inspection were performed. Impact-echo and impedance spectroscopy methods were used to investigate the effect of heat exposure. The use of rubber aggregates led to reduction of strength values and water absorption. The use of polymeric admixtures further decreased water absorption and inhibited compressive strength loss and delayed mass loss when the specimens were stored in acid solutions. The acoustic and electric measurements showed that the use of rubber aggregates or both rubber aggregates and polymers led to reduction of absorption frequency or relative permittivity, respectively. The drop of frequencies was attributed to the formation of microcracks, as well as to decomposition and brittleness of rubber aggregates and polymers. The elevated temperatures resulted in permittivity reduction. The final stage observed after heating at 400°C was the carbonization of the used polymers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The study was performed with support by the Education for Competitiveness Operational Program “Support for the creation of excellent interdisciplinary research teams at Brno University of Technology,” cofinanced by the European Social Fund and the Czech state budget (Registration number: CZ.1.07/2.3.00/30.0005).
References
Alamo-Nole, L. A., Petralez-Perez, O., and Roman-Velazquez, F. R. (2011). “Sorption study of toluene and xylene in aqueous solutions by recycled tires crumb rubber.” J. Hazard. Mater., 185(1), 107–111.
Amari, T., Themelis, N., and Wernick, I. (1999). “Resource recovery from used rubber tires.” Resour. Policy, 25(3), 179–188.
Arioz, O. (2007). “Effects of elevated temperatures on properties of concrete.” Fire Saf. J., 42(8), 516–522.
Arockiasamy, A., Toghiani, H., Oglesby, D., Horstemeyer, M. F., Bouvard, J. L., and King, R. L. (2013). “TG-DSC–FTIR-MS study of gaseous compounds evolved during thermal decomposition of styrene-butadiene rubber.” J. Therm. Anal. Calorim., 111(1), 535–542.
ASTM. (2007). “Measurement of rate of absorption of water by hydraulic-cement concretes.”, West Conshohocken, PA.
ASTM. (2013). “Standard test method for flow of hydraulic cement mortar.”, West Conshohocken, PA.
Beddoe, R. E., and Domer, H. W. (2005). “Modelling acid attack on concrete: Part I: The essential mechanisms.” Cem. Concr. Res., 35(12), 2333–2339.
Benazzouk, A., Douzane, O., Langlet, T., Mezreb, K., Roucoult, J. M., and Quéneudek, M. (2007). “Physico-mechanical properties and water absorption of cement composite containing shredded rubber wastes.” Cem. Concr. Compos., 29(10), 732–740.
Betioli, A. M., Gleize, P. J. P., John, V. M., and Pileggi, R. G. (2012). “Effect of EVA on the fresh properties of cement paste.” Cem. Concr. Compos., 34(2), 255–260.
BSI (British Standards Institution). (2005). "Methods of testing cement—Part 1: Determination of strength.", London.
Cabeza, M., Merino, P., Miranda, A., Nóvoa, X. R., and Sanchez, I. (2002). “Impedance spectroscopy study of hardened portland cement paste.” Cem. Concr. Res., 32(6), 881–891.
Chen, B., and Liu, Y. (2007). “Mechanical properties of polymer-modified concretes containing expanded polystyrene beads.” Constr. Build. Mater., 21(1), 7–11.
Costache, M. C., Jiang, D. D., and Wilkie, C. A. (2005). “Thermal degradation of ethylene-vinyl acetate copolymer nanocomposites.” Polymer, 46(18), 6947–6958.
Czech, Z., and Pełech, R. (2009). “Thermal degradation of butyl acrylate-methyl acrylate-acrylic acid-copolymers.” J. Therm. Anal. Calorim., 96(2), 583–586.
Dubinsky, S., Grader, G. S., Shter, G. E., and Silverstein, M. S. (2004). “Thermal degradation of poly(acrylic acid) containing cooper nitrite.” Polym. Degrad. Stabil., 86(1), 171–178.
Fowler, D. W. (1999). “Polymers in concrete: A vision for the 21st century.” Cem. Concr. Compos., 21(5–6), 449–452.
Georgali, B., and Tsakiridis, P. E. (2005). “Microstructure of fire-damaged concrete. A case study.” Cem. Concr. Compos., 27(2), 255–259.
Haydary, J., Koreňová, Z., Jelemenský, Ľ., and Markoš, J. (2008). “Thermal decomposition of waste polymers.” Proc., Thermophysics 2008 Conf., STU, Bratislava, Slovakia, 62–68.
Hwang, E.-H., Ko, Y. S., and Jeon, J.-K. (2008). “Effect of polymer cement modifiers on mechanical and physical properties of polymer-modified mortar using recycled artificial marble waste fine aggregate.” J. Ind. Eng. Chem., 14(2), 265–271.
Khaloo, A. R., Dehestani, M., and Rahmatabadi, P. (2008). “Mechanical properties of concrete containing a high volume of tire-rubber particles.” Waste Manage., 28(12), 2472–2482.
Kořenská, M., Chobola, Z., Sokolář, R., Mikulková, P., and Martinek, J. (2006). “Frequency inspection as an assessment tool for the frost resistance of fired roof tiles.” Ceram.-Silikaty, 50(3), 185–192.
Kusák, I., Luňák, M., and Schauer, P. (2013). “Tracing of concrete hydration by means of impedance spectroscopy (new tool for building elements testing).” Appl. Mech. Mater., 248, 370–378.
Luňák, M., Kusák, I., and Chobola, Z. (2014). “Dielectric properties of concrete specimens after heat stress.” Appl. Mech. Mater., 446, 1389–1394.
Luňák, M., Kusák, I., Pazdera, L., Topolář, L., and Bílek, V. (2010). “Monitoring of cement-based material solidification, focusing on electrical properties.” Proc., ESA 2010 Conf., Palacky Univ., Olomouc, Czech Republic, 233–240.
Mansur, A. A. P., do Nascimento, O. L., and Mansur, H. S. (2009). “Physico-chemical characterization of EVA-modified mortar and porcelain tiles interfaces.” Cem. Concr. Res., 39(12), 1199–1208.
Mazal, P., Dvoracek, J., and Pazdera, L. (2011). “Application of acoustic emission method in contact damage identification.” Int. J. Mater. Prod. Technol., 41(1–4), 140–152.
Morsy, M. S., Al-Salloum, Y. A., Abbas, H., and Alsayed, S. H. (2012). “Behavior of blended cement mortars containing nano-metakaolin at elevated temperatures.” Constr. Build. Mater., 35, 900–905.
Ohama, Y. (1998). “Polymer-based admixtures.” Cem. Concr. Compos., 20(2–3), 189–212.
Pelisser, F., Barcelos, A., Santos, D., Peterson, M., and Bernardin, A. M. (2012). “Lightweight concrete production with low portland cement consumption.” J. Clean. Prod., 23(1), 68–74.
Pelisser, F., Zavarise, N., Longo, T. A., and Bernardin, A. M. (2011). “Concrete made with recycled tire rubber: Effect of alkaline activation and silica fume addition.” J. Clean. Prod., 19(6–7), 757–763.
Plšková, I., Chobola, Z., and Matysík, M. (2011). “Assessment of ceramic tile frost resistance by means of the frequency inspection method.” Ceram.-Silikaty, 55(2), 176–182.
Plšková, I., Matysík, M., and Chobola, Z. (2010). “Optimizing the location of piezoelectric sensors.” T. Transport. Sci., 3(1), 23–28.
Ray, I., Gupta, A. P., and Biswas, M. (1994). “Effect of latex and superplasticiser on portland cement mortar in the fresh state.” Cem. Concr. Compos., 16(4), 309–316.
Rimez, B., Rahier, H., Van Assche, G., Artoos, T., Biesemans, M., and Van Mele, B. (2008). “The thermal degradation of poly(vinyl acetate) and poly(ethylene-co-vinyl acetate), Part I: Experimental study of the degradation mechanism.” Polym. Degrad. Stab., 93(4), 800–810.
Rohana Yahya, Y. S., Azura, A. R., and Ahmad, Z. (2011). “Effect of curing systems on thermal degradation behaviour of natural rubber (SMR CV 60).” J. Phys. Sci., 22(2), 1–14.
Rossignolo, J. A., and Agnesini, M. V. C. (2002). “Mechanical properties of polymer-modified lightweight aggregate concrete.” Cem. Concr. Res., 32(3), 329–334.
Seidelt, S., Müller-Hagedorn, M., and Bockhorn, H. (2006). “Description of tire pyrolysis by thermal degradation behaviour of main components.” J. Anal. Appl. Pyrolysis, 75(1), 11–18.
Silva, D. A., John, V. M., Ribeiro, J. L. D., and Roman, H. R. (2001). “Pore size distribution of hydrated cement pastes modified with polymers.” Cem. Concr. Res., 31(8), 1177–1184.
Silva, D. A., Roman, H. R., and Gleize, P. J. P. (2002). “Evidences of chemical interaction between EVA and hydrating portland cement.” Cem. Concr. Res., 32(9), 1383–1390.
Toutanji, H. A. (1996). “The use of rubber tire particles in concrete to replace mineral aggregates.” Cem. Concr. Compos., 18(2), 135–139.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Mar 3, 2015
Accepted: Jul 20, 2015
Published online: Oct 19, 2015
Discussion open until: Mar 19, 2016
Published in print: Apr 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.