Effect of Nanosilica on Rheology, Fresh Properties, and Strength of Cement-Based Grouts
Publication: Journal of Materials in Civil Engineering
Volume 27, Issue 4
Abstract
The effect of colloidal nanosilica on the fresh and rheological parameters, plastic shrinkage, heat of hydration, and compressive strength of cement-based grouts is investigated in this paper. The fresh and rheological properties were evaluated by the minislump flow, Marsh cone flow time, Lombardi plate cohesion meter, yield value, and plastic viscosity. The key parameters investigated were the dosages of nanosilica and superplasticizer and temperature of mixing water. Statistical models and isoresponse curves were developed to capture the significant trends. The dosage of nanosilica had a significant effect on the results. The increase in the dosage of nanosilica led to increasing the values of flow time, plate cohesion meter, yield stress, plastic viscosity, heat of hydration at 1 day and 3 days, and compressive strength at 1 day, while reducing the minislump, plastic shrinkage up 24 h, and compressive strength at 3, 7, and 28 days. Conversely, the increase in the dosage of superplasticizer led to decreasing the values of flow time, plate cohesion meter, yield stress, plastic viscosity, heat of hydration at 1 day and 3 days, and compressive strength at 1 day, while increasing the minislump, plastic shrinkage, and compressive strength at 3 and 7 days. Increasing the temperature of mixing water led to a notable increase in the results of minislump, flow time, plastic viscosity, heat of hydration at 3 days, and compressive strength at 1 day, while it reduced the plate cohesion, compressive strength at 3, 7, and 28 days. The statistical models developed in this study can facilitate optimizing the mixture proportions of grouts for target performance by reducing the number of trial batches needed.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (2007). “Standard specification for chemical admixtures for concrete.” ASTM C494, West Conshohocken, PA.
Björnström, J., Martinelli, A., Matic, A., Börjesson, L., and Panas, I. (2004). “Accelerating effects of colloidal nano-silica for beneficial calcium–silicate–hydrate formation in cement.” Chem. Phys. Lett., 392(1–3), 242–248.
British Standards Institution (BSI). (2000). “Cement—Part 1: Composition, specifications and conformity criteria for common cements.” BS EN 197-1:2000, London.
Collepardi, S., Borsoi, A., Ogoumah Olagot, J. J., Troli, R., Collepardi, M., Cursio, A. Q. (2005). “Influence of nano-sized mineral additions on performance of SCC.” Proc., 6th Int. Congress, Global Construction, Ultimate Concrete Opportunities, R. K. Dhir, K. A. Paine, and M. C. Tang, Thomas Telford, Technology and Engineering, Dundee, U.K., 5–7.
Ferguson, J., and Kemblowski, Z. (1991). Applied fluid rheology, Elsevier Applied Science, London, 199–231.
Golaszewki, J., and Szwabowski, J. (2004). “Influence of superplasticizer on rheological behaviour of fresh cement mortars.” Cem. Concr. Res., 34(2), 235–248.
Harington, J. (1965). “The desirability function.” Ind. Qual. Control, 21, 494–498.
Herschel, W. H., and Bulkley, R. (1926). “Measurement of consistency as applied to rubber-benzene solutions.” Proc., ASTM, Part II, 26, 621–629.
Jo, B. W., Kim, C. H., Tae, G. O., and Park, J. B. (2007). “Characteristics of cement mortar with nano- particles.” Constr. Build. Mater., 21(6), 1351–1355.
Jolicoeur, C., Sharman, J., Otis, N., Lebel, A., Simard, M. A., and Page, M. (1997). “The influence of temperature on the rheological properties of superplasticized cement pastes.” Proc., 5th CANMET/ACI Int. Conf. on Superplasticizers and Other Chemical Admixtures in Concrete, ACI SP 173, V. M. Malhotra, ed., ACI, Rome, 379–415.
Li, H., Gang, H., Jie, X., Yuan, J., and Ou, J. (2004). “Microstructure of cement mortar with nano particles.” Composites Part B, 35(2), 185–189.
Lowke, D. (2009). “Interparticle forces and rheology of cement based suspensions.” Proc., NICOM3—Nanotechnology in Construction, Springer, Heidelberg, Germany, 295–301.
Montgomery, D. (2001). Design and analysis of experiments, Wiley, New York.
Nehdi, M., and Al Martini, S. (2007). “Effect of temperature on oscillatory shear behavior of portland cement paste incorporating chemical admixtures.” J. Mater. Civ. Eng., 1090–1100.
Petit, J. Y., Wirquin, E., and Duthoit, B. (2005). “Influence of temperature on the yield value of highly flowable micromortars made with sulfonate-based superplasticizer.” Cem. Concr. Res., 35(2), 256–266.
Petit, J.-Y., Khayat, K., and Wirquin, E. (2009). “Coupled effect of time and temperature on variations of yield value of highly flowable mortar.” Cem. Concr. Res., 39(3), 165–170.
Qing, Y., Zenan, Z., Deyu, K., and Rongshen, C. (2007). “Influence of nano- addition on properties of hardened cement paste as compared with silica fume.” Constr. Build. Mater., 21(3), 539–545.
Senff, L, Labrincha, J. A., Ferreira, V. M., Hotza, D., and Repette, W. L. (2009). “Effect of nano-silica on rheology and fresh properties of cement pastes and mortars.” Constr. Build. Mater., 23(7), 2487–2491.
Sonebi, M. (2006). “Rheological properties of grouts with viscosity modifying agents as diutan gum and welan gum incorporating pulverised fly ash.” Cem. Concr. Res., 36(9), 1609–1618.
Sonebi, M. (2010). “Optimization of cement grouts containing silica fume and viscosity modifying admixture.” J. Mater. Civ. Eng., 332–342.
Sonebi, M., Lachemi, M., and Hossain, K. M. A. (2013). “Optimisation of rheological parameters and mechanical properties of superplasticised cement grouts containing metakaolin and viscosity modifying admixture.” Constr. Build. Mater., 38(1), 126–138.
Yamamoto, Y., and Kobayashi, S. (1986). “Effect of temperature on the properties of superplasticized concrete.” ACI Mater. J., 83(1), 80–87.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Oct 1, 2013
Accepted: Mar 10, 2014
Published online: Jul 22, 2014
Discussion open until: Dec 22, 2014
Published in print: Apr 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.