Environment-Assisted Degradation of the Bond between Steel and Carbon-Fiber-Reinforced Polymer
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 9
Abstract
This paper summarizes the environmentally assisted degradation of the bond between steel and carbon fiber–reinforced polymer (CFRP) composites through analysis of the mechanical performance of loaded and unloaded steel/CFRP double strap joints exposed to various harsh environments such as elevated temperatures, seawater, cyclic temperature and humidity, and ultraviolet (UV) radiation. It was found that both joint stiffness and strength significantly decreased by up to 80% when tested at elevated temperatures near to or greater than of the adhesive used. The mechanical properties reduced by about 20% when exposed to seawater for up to 1 year. Although no significant reduction in stiffness and strength were found when the unloaded joints were exposed to cyclic temperature between 20 and 50°C with the added presence of humidity, the loaded joints catastrophically failed during the exposure, showing that the combination of load, temperature, and moisture was the most critical scenario. In addition, UV exposure also led to a decrease in strength but an increase in stiffness for the unloaded joints, caused by the postcuring with the heat supplied by the UV rays.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge Mr. Long Goh and Mr. Kevin Nievaart for their assistance in conducting the experiments at the Monash University Civil Engineering Laboratory. Thanks are also due to Dr. Gerald Ecclest of the CSIRO, Melbourne, who provided access to the UV exposure facilities and Amroy Europe Oy, Finland, for the supply of the epoxy materials. Financial support was received from the Australian Research Council and Monash University. The first author, Dr. Yu Bai, is the recipient of the Australian Research Council Discovery Early Career Researcher Award.
References
Abanilla, M. A., Li, Y., and Karbhari, V. M. (2005). “Durability characterization of wet layup graphite/epoxy composites used in external strengthening.” Compos. Part B Eng., 37(2–3), 200–212.
Al-Shawaf, A. (2010). “Characterization of bonding behavior between wet-layup carbon fibre reinforced polymer and steel plates in double-strap joints under extreme environmental temperatures.” Ph.D. thesis, Monash Univ, Clayton, Australia.
Bai, Y., and Keller, T. (2009). “Modeling of strength degradation for fiber-reinforced polymer composites in fire.” J. Compos. Mater., 43(21), 2371–2385.
Bai, Y., and Keller, T. (2011). “Effects of thermal loading history on structural adhesive modulus across glass transition.” Constr. Build. Mater., 25(4), 2162–2168.
Bai, Y., Keller, T., and Vallee, T. (2008). “Modeling of stiffness of FRP composites under elevated and high temperatures.” Compos. Sci. Technol., 68(15–16), 3099–3106.
Bai, Y., Nguyen, T., Al-Mahaidi, R., and Zhao, X. L. (2013). “Enhancement of steel/CFRP adhesively-bonded joints at elevated temperatures through curing.” Aust. J. Struct. Eng., in press.
Bowditch, M. R. (1996). “The durability of adhesive joints in the presence of water.” Int. J. Adhes. Adhes., 16(2), 73–79.
Crocombe, A., Hua, Y., Loh, W., Wahab, M., and Ashcroft, I. (2006). “Predicting the residual strength for environmentally degraded adhesive lap joints.” Int. J. Adhes. Adhes., 26(5), 325–336.
Danieley, N. D., and Long, E. R. (1981). “Effects of curing on the glass transition temperature and moisture absorption of a neat epoxy resin.” J. Polym. Sci. Polym. Chem. Ed., 19(10), 2443–2449.
Dawood, M., and Rizkalla, S. (2010). “Environmental durability of a CFRP system for strengthening steel structures.” Constr. Build. Mater., 24(9), 1682–1689.
Ebnesajjad, S., ed. (2008). Adhesives technology handbook, William Andrew Publishing, New York.
Feldman, D. (2002). “Polymer weathering: Photo-oxidation.” J. Polym. Environ., 10(4), 163–173.
Francis, M., and Mirabella, R. (1983). “Strength of interaction and penetration of infrared radiation for polymer films in internal reflection spectroscopy.” J. Polym. Sci. Polym. Phys. Ed., 21(11), 2403–2417.
Hart-Smith, L. J. (1973). “Adhesive-bonded single-lap joints.”, National Aeronautics and Space Administration, Washington, DC.
Hollaway, L. C., and Cadei, J. (2002). “Progress in the technique of upgrading metallic structures with advanced polymer composites.” Prog. Struct. Eng. Mater., 4(2), 131–148.
Huntsman. (2007). “Araldite® 2014-1 structural adhesives technical data sheet.” Huntsman Advanced Materials, Basel, Switzerland.
Karbhari, V., et al. (2003). “Durability gap analysis for fiber-reinforced polymer composites in civil infrastructure.” J. Compos. Constr., 238–247.
Karbhari, V., and Abanilla, M. (2007). “Design factors, reliability, and durability prediction of wet layup carbon/epoxy used in external strengthening.” Compos. Part B Eng., 38(1), 10–23.
Karbhari, V., and Shulley, S. (1995). “Use of composites for rehabilitation of steel structures—Determination of bond durability.” J. Mater. Civ. Eng., 239–245.
Kinloch, A. J. (1987). Adhesion and adhesives: Science and technology, Cambridge University Press, U.K.
Klaiber, F. W., Dunker, K. F., Wipf, T. J., and Sanders, W. W. (1988). “Methods of strengthening existing highway bridges.”, Transportation Research Board, Washington, DC.
Larsson, F. (1986). “Effect of ultraviolet light on mechanical properties of Kevlar 49 composites.” J. Reinf. Plast. Compos., 5(1), 19–22.
Liau, W. B., and Tseng, F. P. (1998). “The effect of long term ultraviolet light irradiation on polymer matrix composites.” Polymer Composites, 19(4), 440–445.
Liu, H., Zhao, X. L., and Al-Mahaidi, R. (2009). “Prediction of fatigue life for CFRP-strengthened steel plates.” Thin-Walled Struct., 47(10), 1069–1077.
Liu, H. B., Zhao, X. L., and Al-Mahaidi, R. (2010). “Effect of fatigue loading on bond strength between CFRP sheets and steel plates.” Int. J. Struct. Stab. Dyn., 10(1), 1–20.
Meier, U. (1995). “Strengthening of structures using carbon fibre/epoxy composites.” Constr. Build. Mater., 9(6), 341–351.
Miller, T. C., Chajes, M. J., Mertz, D. Z., and Hastings, J. N. (2001). “Strengthening of a steel bridge girder using CFRP plates.” J. Bridge Eng., 514–522.
Nguyen, T. C., Bai, Y., Zhao, X. L., and Al-Mahaidi, R. (2011). “Mechanical characterization of steel/CFRP double strap joints at elevated temperatures.” Compos. Struct., 93(6), 1604–1612.
Nguyen, T. C., Bai, Y., Al-Mahaidi, R., and Zhao, X. L. (2012a). “Time-dependent behaviour of steel/CFRP double strap joints subjected to combined thermal and mechanical loading.” Compos. Struct., 94(5), 1826–1833.
Nguyen, T. C., Bai, Y., Zhao, X. L., and Al-Mahaidi, R. (2012b) “Durability of steel/CFRP double strap joints exposed to sea water, cyclic temperature and humidity.” Compos. Struct., 94(5), 1834–1845.
Nguyen, T. C., Bai, Y., Zhao, X. L., and Al-Mahaidi, R. (2012c). “Effects of ultraviolet radiation and associated elevated temperature on mechanical performance of steel/CFRP double strap joints.” Compos. Struct., 94(12), 3563–3573.
Nguyen, T. C., Bai, Y., Zhao, X. L., and Al-Mahaidi, R. (2013). “Curing effects on steel/CFRP double strap joints under combined mechanical load, temperature and humidity.” Constr. Build. Mater., 40, 899–907.
Petrie, E. M. (2007). Handbook of adhesives and sealants, McGraw-Hill, New York.
Rizkalla, S., Dawood, M., and Schnerch, D. (2008). “Development of a carbon fiber reinforced polymer system for strengthening steel structures.” Compos. Part A Appl. Sci. Manuf., 39(2), 388–397.
Sadler, P. A., and Burn, S. (2005). Ultraviolet radiation correlation for accelerated and natural weathering, CSIRO, Melbourne, Australia.
Schnerch, D., and Rizkalla, S. (2008). “Flexural strengthening of steel bridges with high modulus CFRP strips.” J. Bridge Eng., 192.
Shokrieh, M. M., and Bayat, A. (2007). “Effects of ultraviolet radiation on mechanical properties of glass/polyester composites.” J. Compos. Mater., 41(20), 2443–2455.
Tavakkolizadeh, M. (2003). “Fatigue strength of steel girders strengthened with carbon fiber reinforced polymer patch.” J. Struct. Eng., 186–196.
Thrall, E. W., and Shannon, R. W. (1985). Adhesive bonding of aluminum alloys, Marcel Dekker, New York.
Xu, T., Li, G., and Pang, S. S. (2011). “Effects of ultraviolet radiation on morphology and thermo-mechanical properties of shape memory polymer based syntactic foam.” Compos. Part A Appl. Sci. Manuf., 42(10), 1525–1533.
Zhang, Y., Vassilopoulos, A. P., and Keller, T. (2010). “Effects of low and high temperatures on tensile behavior of adhesively-bonded GFRP joints.” Compos. Struct., 92(7), 1631–1639.
Zhao, X. L., and Zhang, L. (2007). “State-of-the-art review on FRP strengthened steel structures.” Eng. Struct., 29(8), 1808–1823.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 13, 2013
Accepted: Oct 3, 2013
Published online: Oct 5, 2013
Published in print: Sep 1, 2014
Discussion open until: Oct 13, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.