Modeling the Primary and Secondary Regions of Creep Curves for SBS-Modified Asphalt Mixtures under Dry and Wet Conditions
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 5
Abstract
This study was conducted to model the primary and the secondary regions of creep curves, derived from dynamic creep tests, for dense graded polymer modified asphalt mixtures under different moisture conditions. For this purpose, 96 Marshall specimens containing siliceous crushed stone aggregate with penetration bitumen, modified with 4.5% of styrene-butadiene-styrene (SBS) polymer modifier, were fabricated and tested at four different loading frequencies, four different temperatures, and two moisture conditions, dry and wet, with three replicate specimens for each experimental combination. Statistical analyses were carried out on the test results and two approaches were proposed to model the creep curves. In addition, a stepwise method was proposed by which it is possible to estimate the location of the boundary point connecting the primary to the secondary regions of the creep curves. The proposed models were compared to the previous ones, and demonstrated to be more accurate.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (1984). “Standard method of test for coating and stripping of bitumen-aggregate mixtures.” T182, Washington, DC.
AASHTO. (2006). “Standard method of test for specific gravity of soils.” T100, Washington, DC.
Archilla, A. R., Diaz, L. G., and Carpenter, S. H. (2007). “Proposed method to determine the flow number from laboratory axial repeated loading tests in bituminous mixtures.”, Transportation Research Board, Washington, DC.
Aschenbrener, T., and Currier, G. (1993). “Influence of testing variables on the results from the Hamburg wheel-tracking device.”, Colorado Department of Transportation (CDOT), Denver, CO.
ASTM. (1995). “Standard test method for effect of moisture on asphalt concrete paving mixtures.” D4867, West Conshohocken, PA.
ASTM. (2009). “Standard test method for sand equivalent value of soils and fine aggregate.” D2419-09, West Conshohocken, PA.
ASTM. (2006). “Standard test method for resistance to degradation of small-size coarse aggregate by abrasion and impact in the Los Angeles machine.” C131-06, West Conshohocken, PA.
ASTM. (2004a). “Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate.” C127-04, West Conshohocken, PA.
ASTM. (2004b). “Standard test method for density, relative density (specific gravity), and absorption of fine aggregate.” C128-04, West Conshohocken, PA.
ASTM. (2013a). “Standard test method for determining the percentage of fractured particles in coarse aggregate.” D5821-13, West Conshohocken, PA.
ASTM. (2013b). “Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate.” C88-13, West Conshohocken, PA.
BS. (2012). “Tests for geometrical properties of aggregates. Determination of particle shape. Flakiness index.” EN 933-3, London, U.K.
Biligiri, K. P., Kaloush, K. E., Mamlouk, M. S., and Witczak, M. W. (2007). “Rational modeling of tertiary flow for asphalt mixtures.”, Transportation Research Board, Washington, DC, 63–72.
Christensen, D. W. (1998). “Analysis of creep data from indirect tension test on asphalt concrete.” J. Assoc. Asphalt Paving Technol., 67, 458–492.
Izzo, R. P., and Tahmoressi, M. (1999). “Testing repeatability of the Hamburg wheel-tracking device and replicating wheel-tracking devices among different laboratories.” J. Assoc. Asphalt Paving Technol., 68, 589–612.
Kalyoncuoglu, S. F., and Tigdemir, M. (2011). “A model for dynamic creep evaluation of SBS modified HMA mixtures.” Constr. Build. Mater., 25(2), 859–866.
Khodaii, A., and Mehrara, A. (2009). “Evaluation of permanent deformation of unmodified and SBS modified asphalt mixtures using dynamic creep test.” Constr. Build. Mater., 23(7), 2586–2592.
Khodaii, A., Moghadas Nejad, F., Forough, S. A., and Saleh Ahari, A. (2014). “Investigating the effects of loading frequency and temperature on moisture sensitivity of SBS-modified asphalt mixtures.” J. Mater. Civ. Eng., 897–903.
Kim, Y. R. (2009). Modeling of asphalt concrete: McGraw-Hill construction, ASCE, Reston, VA.
Mehrara, A., and Khodaii, A. (2011). “Evaluation of asphalt mixtures’ moisture sensitivity by dynamic creep test.” J. Mater. Civ. Eng., 23(2), 212–219.
Mirzahosseini, M. R., Aghaeifar, A., Alavi, A. H., and Gandomi, A. H. (2011). “Permanent deformation analysis of asphalt mixtures using soft computing techniques.” Expert Syst. Appl., 38(5), 6081–6100.
Monismith, C. L., Ogawa, N., and Freeme, C. R. (1975). “Permanent deformation characteristics of subgrade soils due to repeated loading.”, Transportation Research Board, Washington, DC, 1–17.
National Cooperative Highway Research Program (NCHRP). (2002). “Simple performance test for Superpave mix design, Appendix C.”, Transportation Research Board, National Research Council, National Agency Press, Washington, DC.
Sousa, J. B., et al. (1994). “Permanent deformation response of asphalt aggregate mixes.”, Strategic Highway Research Program, National Research Council, Washington, DC, 437.
West, R. C., Zhang, J., and Cooley, L. A. (2004). “Evaluation of the asphalt pavement analyzer for moisture sensitivity testing.”, National Center for Asphalt Technology (NCAT), Auburn Univ., Auburn, AL.
Zhou, F., and Scullion, T. (2003). “Preliminary field validation of simple performance tests for permanent deformation.”, Transportation Research Board, Washington, DC, 209–216.
Zhou, F., Scullion, T., and Sun, L. (2004). “Verification and modeling of three-stage permanent deformation behavior of asphalt mixes.” J. Transp. Eng., 486–494.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 9, 2013
Accepted: May 20, 2013
Published online: May 22, 2013
Discussion open until: Oct 22, 2013
Published in print: May 1, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.