Long-Term Performance of Rigid Plastic Foam Building Insulation
Publication: Journal of Materials in Civil Engineering
Volume 26, Issue 2
Abstract
This article focuses on the characteristics of rigid plastic foam building insulation (RPFBI), one of several types of insulation available for new and retrofit applications. Most RPFBI currently in service incorporates a low thermal conductivity and low-flammability blowing agent within the cells of the foam matrix to enhance thermal and fire performance. Blowing agents diffuse out of the foam matrix with time, and environmental gases diffuse in, with concomitant changes in performance. To address the thermal performance issue, international standards organizations have developed standards that define thermal performance averaged over a specific time frame or assumed lifetime. These standards have several limitations that may result in inaccurate estimates of long-term performance, as well as confusion among stakeholders. None of the standards address possible changes in fire performance through time. This paper presents a review of the standards and literature regarding thermal and fire performance of RPFBI, and a call for harmonization and consistency across standards addressing thermal performance, fire behavior, durability, and service life.
Get full access to this article
View all available purchase options and get full access to this article.
References
Anderson, J. J. (1963). “Retention of flame properties of rigid polyurethane foams.” Ind. Eng. Chem. Prod. Res. Dev., 2(4), 260–263.
Arthur D. Little, Inc. (2002). “Global comparative analysis of HFC and alternative technologies for refrigeration, air conditioning, foam, solvent, aerosol propellant, and fire protection applications.” Final Report, Alliance for Responsible Atmospheric Policy (ARAP), Cambridge, MA.
Ashford, P., Mizuno, K., and Quintero, M. (2005). “Montreal protocol on substances that deplete the ozone layer. UNEP technology and economic assessment panel.” Rep. of the Task Force on Foam End-of-Life Issues, Vol. 3, United Nations Environment Programme (UNEP) Technology and Economic Assessment Panel (TEAP), Nairobi, Kenya.
ASTM. (2000). “Standard test method for estimating the long-term change in the thermal resistance of unfaced rigid closed-cell plastic foams by slicing and scaling under controlled laboratory conditions.” C1303, West Conshohocken, PA.
ASTM. (2010). “Standard specification for rigid, cellular polystyrene thermal insulation.” C578, West Conshohocken, PA.
ASTM. (2011a). “Standard specification for faced rigid cellular polyisocyanurate thermal insulation board.” C1289, West Conshohocken, PA.
ASTM. (2011b). “Standard test method for surface burning characteristics of building materials.” E84, West Conshohocken, PA.
ASTM. (2012). “Standard test method for predicting long-term thermal resistance of closed-cell foam insulation.” C1303, West Conshohocken, PA.
Bohne, R. A., Bergsdal, H., Brattebø, H., and Hovde, P. J. (2006). “Estimation of the service life of buildings and building components.” Towards the City Surface of Tomorrow—Conf. Proc., P. H. Brunner, T. Jakl, and E. Ober, eds., Federal Ministry of Agriculture, Forestry, Environment and Water Management (Lebensministerium), Vienna, Austria, 29–33.
Bomberg, M. T., and Kumaran, M. K. (1991). “Progress report on long-term thermal performance of polyisocyanurate boardstock materials.” Internal Rep., National Research Council Canada, Institute for Research in Construction, Ottawa, ON, Canada.
Bradley, P. E., and Kohler, N. (2007). “Methodology for the survival analysis of urban building stocks.” Build. Res. Inform., 35(5), 529–542.
Cabeza, L. F., Castell, A., Medrano, M., Martorell, I., Pérez, G., and Fernández, I. (2010). “Experimental study on the performance of insulation materials in Mediterranean construction.” Energ. Build., 42(5), 630–636.
Chattopadhyay, D. K., and Webster, D. C. (2009). “Thermal stability and flame retardancy of polyurethanes.” Progr. Polymer Sci., 34(10), 1068–1133.
Cole, R. J., and Kernan, P. C. (1996). “Life-cycle energy use in office buildings.” Build. Environ., 31(4), 307–317.
Daouas, N. (2011). “A study on optimum insulation thickness in walls and energy savings in Tunisian buildings based on analytical calculation of cooling and heating transmission loads.” Appl. Energ., 88(1), 156–164.
Ding, G. K. C. (2007). “Life cycle energy assessment of Australian secondary schools.” Build. Res. Inform., 35(5), 487–500.
Doroudiani, S., and Omidian, H. (2010). “Environmental, health and safety concerns of decorative mouldings made of expanded polystyrene in buildings.” Build. Environ., 45(3), 647–654.
Dournel, P., and Zipfel, L. (2003). “Analysis of the evolution of PIR foams in the context of the phase out of HCFCs.” J. Cell. Plast., 39(3), 211–227.
European Committee for Standardization (CEN). (2008a). “Thermal insulation products for buildings—factory made products of extruded polystyrene foam (XPS)—specification.” 13164, Brussels, Belgium.
European Committee for Standardization (CEN). (2008b). “Thermal insulation products for buildings—factory made products of phenolic foam (PF)—specification.” 13166, Brussels, Belgium.
European Committee for Standardization (CEN). (2008c). “Thermal insulation products for buildings—factory made rigid polyurethane foam (PUR) products—specification.” 13165, European Committee for Standardization (CEN), Brussels, Belgium.
Extruded Polystyrene Foam Association (XPSA). (2003). “Labeling and advertising of home insulation comments.”, Federal Trade Commission, Washington, DC.
Fabian, B. A., Graves, R. S., Hofton, M. R., and Yarbrough, D. W. (1997). “A variability study on the ASTM thin slicing and scaling test method for evaluating the long-term performance of an extruded polystyrene foam blown with HCFC-142b.” Insulation materials: Testing and applications, Vol. 3, R. S. Graves and R. R. Zarr, eds., ASTM International, West Conshohocken, PA, 197–215.
Federal Trade Commission (FTC). (2005). “Labeling and advertising of home insulation: Trade regulation rule.”, Washington, DC.
Gann, R. G. (2004). “Estimating data for incapacitation of people by fire smoke.” Fire Tech., 40(2), 201–207.
Graham, M. S. (2003). “Comparing polyiso -values.” Professional roofing, April, 61.
Graham, M. S. (2006). “Testing LTTR: Research reveals the LTTR method may be over-reporting results.” Professional roofing, January, 30–31.
Graham, M. S. (2010a). “Revised -values: NRCA has revised its longstanding design -value recommendation for polyisocyanurate insulation.” Professional roofing, December, 20.
Graham, M. S. (2010b). “R-value concerns: -values are found to be below LTTR.” Professional roofing, May, 24.
Harju, M., Heimstad, E. S., Herzke, D., Sandanger, T., Posner, S., and Wania, F. (2008). current state of knowledge and monitoring requirements: Emerging “new” brominated flame retardants in flame retarded products and the environment, Norwegian Pollution Control Authority (SFT), Oslo, Norway.
Harvey, L. D. D. (2007). “Net climatic impact of solid foam insulation produced with halocarbon and non-halocarbon blowing agents.” Build. Environ., 42(8), 2860–2879.
Hull, T. R., and Paul, K. T. (2007). “Bench-scale assessment of combustion toxicity–A critical analysis of current protocols.” Fire Saf. J., 42(5), 340–365.
ISO. (1989). “Tests for measuring ‘reaction-to-fire’ of building materials—their development and application.” 3814, Geneva.
ISO. (1999). “Ageing of thermal insulation materials—determination of the long-term change in thermal resistance of closed-cell plastics (accelerated laboratory test methods).” 11561, Geneva.
ISO. (2000). “Buildings and constructed assets—service life planning—part 1: General principles.” 15686-1, Geneva.
ISO. (2002). “Reaction-to-fire tests—heat release, smoke production and mass loss rate—part 1: Heat release rate (cone calorimeter method).” 5660-1, Geneva.
ISO. (2007). “Building materials and products—hygrothermal properties—tabulated design values and procedures for determining declared and design thermal values.” 10456, Geneva.
ISO. (2010a). “Reaction to fire tests—ignitability of products subjected to direct impingement of flame—part 2: Single-flame source test.” 11925-2, Geneva.
ISO. (2010b). “Rigid cellular plastics—thermal insulation products for buildings—specifications.” 4898, Geneva.
Johnstone, I. M. (2001a). “Energy and mass flows of housing: A model and example.” Build. Environ., 36(1), 27–41.
Johnstone, I. M. (2001b). “Energy and mass flows of housing: Estimating mortality.” Build. Environ., 36(1), 43–51.
Kalinger, P., and Drouin, M. (2002). “Closed cell foam insulations: Resolving the issue of thermal performance.” Interface, August, 23–26.
Mahlia, T. M. I., and Iqbal, A. (2010). “Cost benefits analysis and emission reductions of optimum thickness and air gaps for selected insulation materials for building walls in Maldives.” Energy, 35(5), 2242–2250.
Posner, S. (2006). Survey and technical assessment of alternatives to TBBPA and HBCDD, PM, Swedish Chemicals Agency (KemI), Sundbyberg, Sweden.
Roe, R. (2007). “Long term thermal resistance (LTTR): Five years later.” Interface, March, 12–15.
Scheuer, C., Keoleian, G. A., and Reppe, P. (2003). “Life cycle energy and environmental performance of a new university building: Modeling challenges and design implications.” Energ. Build., 35(10), 1049–1064.
Schultz, N. (1991). “Thermal insulation under fire.” Insulation materials: Testing and applications, Vol. 2, R. S. Graves and D. C. Wysocki, eds., ASTM International, Philadelphia, PA, 430–438.
Singh, H., and Jain, A. K. (2009). “Ignition, combustion, toxicity, and fire retardancy of polyurethane foams: A comprehensive review.” J. Appl. Polymer. Sci., 111(2), 1115–1143.
Stec, A. A., and Hull, T. R. (2011). “Assessment of the fire toxicity of building insulation materials.” Energ. Build., 43(2–3), 498–506.
Stovall, T. K., Fabian, B. A., Nelson, G. E., and Beatty, D. R. (2002). “A comparison of accelerated aging test protocols for cellular foam insulation.” Insulation materials testing and applications, Vol. 4, A. O. Desjarlais and R. R. Zarr, eds., ASTM International, West Conshohocken, PA, 379–394.
Tambach, M., Hasselaar, E., and Itard, L. (2010). “Assessment of current Dutch energy transition policy instruments for the existing housing stock.” Energ. Pol., 38(2), 981–996.
Underwriters Laboratories of Canada (ULC). (2003). “Standard test method for determination of long-term thermal resistance of closed-cell thermal insulating foams.”, Underwriters Laboratories of Canada (ULC), Toronto, ON.
Vo, C. V., and Paquet, A. N. (2004). “An evaluation of the thermal conductivity of extruded polystyrene foam blown with HFC-134a or HCFC-142b.” J. Cell. Plast., 40(3), 205–224.
Weil, E. D., and Levchik, S. V. (2004). “Commercial flame retardancy of polyurethanes.” J. Fire Sci., 22(3), 183–210.
Wu, J., Dillon, D., and Crooker, R. (2002). “Hydrochlorocarbons/pentanes coblown PIR foams for improved fire performance.” Proc., API Polyurethane Conf. 2002, Alliance for the Polyurethanes Industry (API), Arlington, VA.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 26 • Issue 2 • February 2014
Pages: 374 - 378
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Sep 18, 2012
Accepted: Mar 11, 2013
Published online: Jan 15, 2014
Published in print: Feb 1, 2014
Discussion open until: Jun 15, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.