Effect of Compaction Temperature on Rutting and Moisture Resistance of Foamed Warm-Mix-Asphalt Mixtures
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 9
Abstract
A laboratory investigation was carried out to study the effects of various compaction temperatures on moisture susceptibility and rutting resistance of warm-mix-asphalt (WMA) mixtures containing moist aggregates using a foaming technology. The experimental design included two aggregate moisture contents (0 and by weight of aggregate dry mass), one lime content (1% lime by weight of dry aggregate), two foaming water contents (2 and 3%) with control, and two aggregate sources. The major properties, such as the gyration number of various samples, indirect tensile strength (ITS), tensile strength ratio, rut depths of dry and conditioned specimens, and deformation (flow), were measured for all mixtures. The test results indicated that the aggregate source significantly affected the ITS and rutting resistance regardless of the foaming water content, compaction temperature, and aggregate moisture content. In addition, mixtures from moist aggregate had lower gyration numbers regardless of aggregate type, foaming technology, and compaction temperature. Moreover, the ITS values of foamed mixtures containing moist aggregate increased as the compaction temperature increased. Furthermore, the rut depths of all the dry and wet mixtures slightly increased as their compaction temperatures decreased regardless of the aggregate moisture content, foaming water contents, and aggregate type. A compaction temperature below 102°C (215°F) generally had no noticeable aging (2 h) effects on the mixture and did not significantly increase the rutting resistance of these WMA mixtures.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2001a). “Standard method of test for determining the rutting susceptibility of hot mix asphalt (APA) using the asphalt pavement analyzer (APA).”, American Association of State and Highway Transportation Officials, Washington, DC.
AASHTO. (2001b). “Standard method of test for resistance of compacted asphalt mixtures to moisture-induced damage.”, American Association of State and Highway Transportation Officials, Washington, DC.
Akisetty, C. K., Lee, S. J., and Amirkhanian, S. (2009). “High temperature properties of rubberized binders containing warm asphalt additives.” Constr. Build. Mater., 23(1), 565–573.
Austerman, A. J., Mogawer, W. S., and Bonaquist, R. (2009). “Evaluating the effects of warm mix asphalt technology additive dosages on the workability and durability of asphalt mixtures containing recycled asphalt pavement.” Proc., 88th Annual Meeting, Transportation Research Board, Washington, DC.
Bennert, T., Maher, A., and Sauber, R. (2011). “Influence of production temperature and aggregate moisture content on the initial performance of warm-mix asphalt.”, Transportation Research Board, Washington, DC, 97–107.
D’Angelo, J., et al. (2008)., Federal Highway Administration, U.S. Dept. of Transportation, Washington, DC.
Diefenderfer, S., and Hearon, A. (2008). “Laboratory Evaluation of a Warm Asphalt Technology for Use in Virginia.”, Virginia Transportation Research Council, Charlottesville, VA.
Gandhi, T. (2008). “Effects of warm asphalt additives on asphalt binder and mixture properties.” Ph.D. dissertation, Clemson University, Clemson, SC.
Hodo, W., Kvasnak, A., and Brown, E. R. (2009). “Investigation of Foamed asphalt (warm mix asphalt) with high reclaimed asphalt pavement (RAP) content for sustainment and rehabilitation of asphalt pavement.” Proc., 88th Annual Meeting, Transportation Research Board, Washington, DC.
Hurley, C., and Prowell, B. (2006). “Evaluation of potential processes for use in warm mix asphalt.” J. Assoc. Asphalt Paving Technol., 75, 41–90.
Kristjansdottir, O., Muench, S., Michael, L., and Burke, G. (2007). “Assessing potential for warm-mix asphalt technology adoption.”, Transportation Research Board, Washington, DC, 91–99.
Kutay, M., and Ozturk, H. (2012). “Investigation of moisture dissipation in foam-based warm mix asphalt using synchrotron-based X-ray microtomography.” J. Mater. Civ. Eng., 24(6), 674–683.
Kvasnak, A., and West, R. (2009). “Case study of warm mix asphalt moisture susceptibility in birmingham.” Proc., 88th Annual Meeting, Transportation Research Board, Washington, DC.
Middleton, B., and Forfylow, R. W. (2009). “Evaluation of warm-mix asphalt produced with the double barrel green process.”, Transportation Research Board, Washington, DC, 19–26.
Mogawer, W., Austerman, A., and Bonaquist, R. (2009). “Evaluating effects of warm-mix asphalt technology additive dosages on workability and durability of asphalt mixtures containing recycled asphalt pavement.” Proc., 88th Annual Meeting, Transportation Research Board, Washington, DC.
Prowell, B. D., and Hurley, G. C. (2007). Warm-mix asphalt: Best practices, National Asphalt Pavement Association, Lanham, MD.
Punith, V. S., Xiao, F., and Amirkhanian, S. N. (2011a). “Effects of moist aggregates on the performance of warm mix asphalt mixtures containing non-foaming additives.” J. Test. Eval., 39(5), 847–857.
Punith, V. S., Xiao, F., and Amirkhanian, S. N. (2011b). “Performance of warm mix asphalt mixtures containing recycled coal ash and roofing shingles with moist aggregates for low volume roads.”, Transportation Research Board, Washington, DC, 48–57.
Scherocman, J. A., and Walker, D. (2008). “Factors affecting asphalt compaction.” Asphalt Institute, Lexington, KY.
Smith, N. (2008). “Double barrel green WMA process.” Astec Industries, Warm Mix Asphalt Systems, 〈http://www.warmmix.org/submissions/55_20080101_Norm%20Smith%20-%20Astec%20Double%20Barrel%20Green.pdf〉 (Feb. 1, 2013).
South Carolina DOT. (2011). “Supplemental technical specification for hot-mix asphalt material properties SCDOT designation.”.
Tao, M., and Mallick, R. (2009). “Evaluation of effects of warm-mix asphalt additives on properties of reclaimed asphalt pavement material.”, Transportation Research Board, Washington, DC, 151–160.
Wayne, H. (2009). “Field and laboratory investigation of foamed asphalt (warm-mix asphalt) with high recycled asphalt pavement content for sustainment and rehabilitation of asphalt pavement.” Proc., 88th Annual Meeting, Transportation Research Board, Washington, DC.
Wielinski, J., Hand, A., and Rausch, D. M. (2009). “Laboratory and field evaluations of foamed warm-mix asphalt projects.”, Transportation Research Board, Washington, DC, 125–131.
Xiao, F., Amirkhanian, S., and Putman, B. (2010a). “Evaluation of rutting resistance in warm mix asphalts containing moist aggregate.”, Transportation Research Board, Washington, DC, 75–84.
Xiao, F., and Amirkhanian, S. N. (2010). “Effects of liquid antistrip additives on rheology and moisture susceptibility of water bearing warm mixtures.” Constr. Build. Mater., 24(9), 1649–1655.
Xiao, F., Jordan, J., and Amirkhanian, S. (2009). “Laboratory investigation of moisture damage in warm-mix asphalt containing moist aggregate.”, Transportation Research Board, Washington, DC, 115–124.
Xiao, F., Punith, V. S., Putman, B., and Amirkhanian, S. N. (2011). “Utilization of foaming technology in warm mix asphalt mixtures containing moist aggregates.” J. Mater. Civ. Eng., 23(9), 1328–1337.
Xiao, F., Zhao, W., Gandhi, T., and Amirkhanian, S. N. (2010b). “Influence of anti-stripping additive on moisture susceptibility of warm mix asphalt mixture.” J. Mater. Civ. Eng., 22(10), 1047–1055.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Apr 25, 2011
Accepted: Aug 16, 2012
Published online: Aug 24, 2012
Discussion open until: Jan 24, 2013
Published in print: Sep 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.