Inverse Analysis of Related Parameters in Calculation of Concrete Drying Shrinkage Based on ANSYS Design Optimization
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 6
Abstract
Drying shrinkage because of moisture diffusion is a critical factor influencing the durability of concrete structures. Numerical simulation of moisture diffusion and drying shrinkage inside concrete, on the basis of the mechanism of drying shrinkage, is significant to better understanding and predicting drying shrinkage-induced cracking. To correctly simulate the drying effect on concrete deformation, diffusion coefficient, surface factor and other factors are essentially required. This paper presents the simulations of shrinkage tests of concrete blended with fly ash and ground granulated blast furnace slag based on the theory of three-dimensional nonlinear moisture diffusion. The related parameters are identified by the inverse finite-element analysis approach using the design optimization module of ANSYS. The environmental humidity effect on shrinkage strain and the relationships between the identified parameters with the fly ash content are discussed.
Get full access to this article
View all available purchase options and get full access to this article.
References
Akita, H., Fujiwara, T., and Ozaka, Y. (1997). “A practical procedure for the analysis of moisture transfer within concrete.” Mag. Concr. Res., 49(179), 129–137.
American Concrete Institute (ACI). (1992). “Prediction of creep, shrinkage and temperature effects in concrete structures.”, Detroit.
Ayano, T., and Wittmann, F. H. (2002). “Drying, moisture distribution, and shrinkage of cement-based materials.” Mater. Struct., 35(3), 134–140.
Baroghel-Bouny, V., Mainguy, M., Lassabatere, T., and Coussy, O. (1999). “Characterization and identification of equilibrium and transfer moisture properties for ordinary and high-performance cementitious materials.” Cem. Concr. Res., 29(8), 1225–1238.
Bažant, Z. P., and Baweja, S. (1995). “Creep and shrinkage prediction model for analysis and design of concrete structures-model B3.” Mater. Struct., 28(6), 357–365.
Bažant, Z. P., and Najjar, L. J. (1972). “Nonlinear water diffusion in nonsaturated concrete.” Mater. Struct., 5(1), 3–20.
Bažant, Z. P., and Xi, Y. P. (1994). “Drying creep of concrete: Constitutive model and new experiments separating its mechanisms.” Mater. Struct., 27(1), 3–14.
Comité Euro-International du Béton. (1993). CEB-FIP model code 1990: Design code, Thomas Telford, London.
Gao, X., Kan, X., and Yang, Y. (2009). “Shrinkage distribution of concrete with one surface exposed to dry condition.” J. Chin. Ceram. Soc., 37(1), 87–91 (in Chinese).
Granger, L., Torrenti, J.-M., and Acker, P. (1997). “Thoughts about drying shrinkage: Scale effects and modeling.” Mater. Struct., 30(2), 96–105.
Gribniak, V., Kaklauskas, G., and Bacinskas, D. (2008). “Shrinkage in reinforced concrete structures: A computational aspect.” J. Civ. Eng. Manage., 14(1), 49–60.
Hou, J., and Yuan, Y. (2008). “Experimental research on internal relative humidity during dying shrinkage of concrete.” New Build. Mater., 35(5), 1–4 (in Chinese).
Huang, D., and Liu, G. (2002). “Experimental study on moisture transfer in concrete under quasi-isothermal condition.” J. Hydraul. Eng., (6), 96–100 (in Chinese).
Jiang, Z., and Wang, P. (2003). “Internal relative humidity distribution of concrete under isothermal drying conditions.” J. Wuhan Univ. Technol, 25(7), 18–21 (in Chinese).
Kim, J. K., and Lee, C. S. (1998). “Prediction of differential drying shrinkage in concrete.” Cem. Concr. Res., 28(7), 985–994.
Li, Z., Perez Lara, M. A., and Bolander, J. E. (2006). “Restraining effects of fibers during non-uniform drying of cement composites.” Cem. Concr. Res., 36(9), 1643–1652.
Penev, D., and Kawamura, M. (1991). “Moisture diffusion in soil-cement mixtures and compacted lean concrete.” Cem. Concr. Res., 21(1), 137–146.
Pleinert, H., Sadouki, H., and Wittmann, F. H. (1998). “Determination of moisture distributions in porous building materials by neutron transmission analysis.” Mater. Struct., 31(4), 218–224.
Rahman, M. K., Baluch, M. H., and Al-Gadhib, A. H. (1999). “Modeling of shrinkage and creep stresses in concrete repair.” ACI Mater. J., 96(5), 542–550.
Sakata, K. (1983). “A study on moisture diffusion in drying and drying shrinkage of concrete.” Cem. Concr. Res., 13(2), 216–224.
Torrenti, J. M., Granger, L., Diruy, M., and Genin, P. (1999). “Modeling concrete shrinkage under variable ambient conditions.” ACI Mater. J., 96(1), 35–39.
West, R. P., and Holmes, N. (2005). “Predicting moisture movement during the drying of concrete floors using finite elements.” Constr. Build. Mater., 19(9), 674–681.
Yuan, Y., and Wan, Z. L. (2002). “Prediction of cracking within early-age concrete due to thermal, drying and creep behavior.” Cem. Concr. Res., 32(7), 1053–1059.
Zhang, J., Qi, K., and Huang, Y. (2009). “Calculation of moisture distribution in early-age concrete.” J. Eng. Mech., 135(8), 871–880.
Zhang, P., Zhao, T.-J., Wittmann, F. H., and Slowik, V. (2010). “Calculation of the moisture diffusion coefficient of cementitious materials by inverse analysis.” J. Hydraul. Eng., 41(1), 55–60 (in Chinese).
Zhu, Y. M., Liu, Y. Z., Cao, W. M., and Wu, J. (2006). “Analysis of concrete moisture dry shrinkage and stress based on mesoscopical model.” J. Hydraul. Eng., 37(10), 1163–1168 (in Chinese).
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jul 22, 2011
Accepted: Jul 2, 2012
Published online: May 15, 2013
Published in print: Jun 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.