Determination of Steel Emissivity for the Temperature Prediction of Structural Steel Members in Fire
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 2
Abstract
A numerical method, with which experimental results were processed, was adopted to measure the total emissivity of mild steel specimens at high temperatures. This method is derived from considering the transient thermal energy equilibrium between a steel specimen and its surrounding heating environment. As a first step to validate this method, the results obtained at a low temperature were compared with those using infrared thermographic techniques, and a good correlation of 87% was achieved. The numerical model was then extended to high temperatures to investigate the variation of emissivity of steel with temperatures. The convective heat transfer coefficient used in the numerical model was examined in great detail using results obtained from transient high temperature tests. The emissivity of steel obtained from this study shows that steel emissivity varies over a range of temperatures and the variation becomes more abrupt between 400 and 500°C. Formulation for the emissivity of steel at rising temperatures is recommended for steel design in fire.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASTM. (2005). “Standard test method for measuring and compensating for emissivity using infrared imaging radiometers.” E1933-99a, West Conshohocken, PA.
Conroy, C., Guthrie, J., Sharkins, A., Sparr, B., Crocombe, R., and Curbelo, R. (1987). “An infrared accessory for studying the emissivity of aluminum surfaces.” Appl. Spectrosc., 41(4), 688–692.
Croft, D., and Stone, J. (1977). Heat transfer calculations using finite difference equations, Applied Science Publishers, Barking, UK.
European Committee for Standardization (CEN). (2005). “Eurocode 3: Design of steel structures—Part 1-2: General rules—Structural fire design.”, Brussels.
Ghojel, J. (1998). “A new approach to modeling heat transfer in compartment fires.” Fire Saf. J., 31(3), 227–237.
Image Processor Pro II, Version 1 [Computer software]. NEC, Irving, TX.
International Organisation of Standardization. (2002). “Fire-resistance tests—Elements of building construction—Part 8: Specific requirements for non-load bearing vertical separating elements.” ISO 834-8:2002, ISO, Geneva, Switzerland.
Kay, T., Kirby, B., and Preston, R. (1996). “Calculation of the heating rate of an unprotected steel member in a standard fire resistance test.” Fire Saf. J., 26(4), 327–350.
Moghaddam, S., Lawler, J., Currano, J., and Kim, J. (2007). “Novel method for measurement of total hemispherical emissivity.” J. Thermophys. Heat Trans., 21(1), 128.
Moran, M., Shapiro, H., Munson, B., and DeWitt, D. (2003). Introduction to thermal systems engineering, Wiley, New York.
Paloposki, T., and Liedquist, L. (2006). “Steel emissivity at high temperatures.” 〈http://www.nordicinnovation.net/nordtestfiler/rep570.pdf〉 (May 11, 2011).
SBI. (1976). Fire engineering design of steel structures, Swedish Institute of Steel Construction, Stockholm, Sweden.
Smith, C., and Stirland, C. (1983). “Analytical methods and the design of steel framed buildings.” Int. Seminar on Three Decades of Structural Fire Safety, Fire Research Station, Borehamwood, Herts, 155–200.
Tanaka, F., Ohira, H., and Naganuma, Y. (1989). Application of a new radiation thermometry method to galvannealed and cold-rolled steels, IEEE, New York, 24–28.
White, D. A., Beyler, C. L., Scheffey, J. L., and Williams, F. W. (1999). “Modeling the impact of post-flashover shipboard fires on adjacent spaces.” J. Fire Protect. Eng., 10(4), 2.
Wong, M. B., and Ghojel, J. (2003a). “Sensitivity analysis of heat transfer formulations for insulated structural steel components.” Fire Saf. J., 38(2), 187–201.
Wong, M. B., and Ghojel, J. (2003b). “Spreadsheet method for temperature calculation of unprotected steelwork subject to fire.” Struct. Des. Tall Special Build., 12(2), 83–92.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Apr 26, 2011
Accepted: Jun 5, 2012
Published online: Aug 29, 2012
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.