Effect of Temperature on Strength and Elastic Modulus of High-Strength Steel
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 2
Abstract
This paper presents the effect of temperature on the mechanical properties of high-strength alloy structural Q460 steel. The strength and stiffness properties of steel degrade with temperature and this deterioration has to be properly accounted for in the fire resistant design of steel structures. The strength and stiffness degradation is also influenced by the composition of steel. Because of a lack of data specific to high-strength Q460 steel, design standards assume the high temperature strength variation of Q460 steel to be same as that of conventional mild steel. To overcome this drawback, strength and stiffness properties of Q460 steel were measured at various temperatures in the range of 20–800°C. A relative comparison of measured data indicates that high-strength steel experiences a slower loss of strength and stiffness with temperature than conventional steel. Data generated from the experiments, namely, load-displacement relationships and vibration frequency, were utilized to develop relations for yield strength, tensile strength, and elastic modulus of Q460 steel as a function of temperature. The proposed relations developed specifically for high-strength Q460 steel can lead to better fire resistance prediction of steel structure systems.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge the support of the Specialized Research Fund for the Doctoral Program of Higher Education (20090191120032), Research Project of Natural Science Foundation of China (51006320) and Natural Science Foundation of Chongqing (CSTC, 2010BB4224). The support from State Key Lab for Disaster Reduction in Civil Engineering of Tongji University in China and Michigan State University through Strategic Partnership Grant (No. 71-4434) is also greatly appreciated. Any opinions, findings, and conclusions or recommendations expressed in this paper are those of the authors and do not necessarily reflect the views of the sponsors.
References
AISC. (2005). “Specification for structural steel buildings.”, Chicago.
ASTM. (2001). “Standard test method for dynamic Young’s modulus, shear modulus, and Poisson’s ratio by impulse excitation of vibration.” E1876-1, West Conshohocken, PA.
ASTM. (2007). “Standard specification for high-strength low-alloy columbium-vanadium structural steel.” A572/A572M-07, West Conshohocken, PA.
ASTM. (2008). “Standard specification for carbon structural steel.” ASTM A36/A36M, West Conshohocken, PA.
ASTM. (2011). “Standard specification for structural steel shapes.” ASTM A992/A992M-11, West Conshohocken, PA.
Ban, H. Y., Shi, G., Shi, Y. J., and Wang, Y. Q. (2011). “Research progress on the mechanical property of high strength structural steels.” Adv. Mater. Res., 250–253, 640–648.
Bjorhovde, R. (2004). “Development and use of high performance steel.” J. Constr. Steel Res., 60(3–5), 393–400.
British Standards Institution (BSI). (1990). “The structural use of steelwork in buildings, Part 8: Code of practice for fire resistant design.”, London.
China Association for Engineering Construction Standardization CECS200. (2006). “Chinese technical code for fire safety of steel structure in buildings.”, China Plan Press, Beijing, China.
Chen, J., and Young, B. (2004). “Mechanical properties of cold-formed steel at elevated temperatures.” Proc., 17th Int. Special Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, MO, 437–466.
Chen, J., and Young, B. (2008). “Design of high strength steel columns at elevated temperatures.” J. Constr. Steel Res., 64(6), 689–703.
Chen, J., Young, B., and Uy, B. (2006). “Behavior of high strength structural steel at elevated temperatures.” J. Struct. Eng., 132(12), 1948–1954.
Chijiwa, R., Yoshida, Y., Uemori, R., Tamehiro, H., Funato, K., and Horii, Y. (1993). “Development and practical application of fire-resistant steel for buildings.” Nippon Steel Tech. Rep., 58, 47–55.
Dolzhenkov, I. E. (1971). “The nature of blue brittleness of steel.” Met. Sci. Heat Treat., 13(3), 220–224.
European Committee for Standardization (CEN). (2005a). “Eurocode 3: Design of steel structures—Part 1.1: General rules and rules for buildings.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2005b). “Eurocode 3: Design of steel structures—Part 1.2: General rules for structural fire design.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2006). “Eurocode 4: Design of composite steel and concrete structures: Part 1.1: General rules and rules for buildings.”, Brussels, Belgium.
European Convention for Constructional Steelworks (ECCS). (2001). “Material properties.” European recommendations for the fire safety of steel structures, Section III.2, ECCS General Secretariat, Brussels, Belgium.
Hong Kong Buildings Dept. (2005). “Code of practice for the structural use of steel.” Government of the Hong Kong Special Administrative Region, Kowloon, Hong Kong.
Japanese Industrial Standard (JIS). (1999). “Japanese industrial standard—Rolled steels for welded structure.”, Japanese Standards Association, Tokyo.
Ji, G. (2004). Handbook of comparative world steel standards, China Standard Press, Beijing, China.
Kirby, B. R., and Preston, P. R. (1988). “High temperature properties of hot-rolled structural steels for use in fire engineering design studies.” Fire Saf. J., 13(1), 27–37.
Kodur, V. K. R., and Harmathy, T. Z. (2008). “Properties of building materials.” SFPE handbook of fire protection engineering, 4th Ed., P. J. DiNenno, ed., National Fire Protection Association, Quincy, MA, 1-167–1-195.
Li, G. Q., Han, L. H., Lou, G. B., and Jiang, S. C. (2006). Fire resistance design of steel structure and composite steel and concrete structure, Chinese Architecture and Building Press, Beijing.
Li, G. Q., Jiang, S. C., and Yin, Y. Z. (2003). “Experimental studies on the properties of constructional steel at elevated temperatures.” J. Struct. Eng., 129(12), 1717–1721.
Li, G. Q., and Zhang, X. J. (2001). “Experimental studies of the material properties of SM41 steel at elevated temperatures.” Indust. Constr., 31(16), 57–59 (in Chinese).
Peng, H. (2009). “Study on the ultimate load bearing capacity of Al-alloy compression members at high temperature.” Master’s thesis, Tongji Univ., Shanghai, China.
Qiang, X. H., Bijlaard, F. S. K., and Kolstein, H. (2012a). “Deterioration of mechanical properties of high strength structural steel S460N under steady state fire condition.” Mater. Des., 36, 438–442.
Qiang, X. H., Bijlaard, F. S. K., and Kolstein, H. (2012b). “Post-fire mechanical properties of high strength structural steels S460 and S690.” Eng. Struct., 35, 1–10.
Qiang, X. H., Bijlaard, F. S. K., and Kolstein, H. (2012c). “Dependence of mechanical properties of high strength steel S690 on elevated temperatures.” Constr. Build. Mater., 30, 73–79.
SANS Power Test, Version 3.3 [Computer software]. MTS Systems (Shanghai) Co., Ltd, Shanghai, China.
Standardization Administration of the People’s Republic of China (SAC). (1988). “Alloy structural steel—Technical requirements.”, China Standard Press, Beijing.
Standardization Administration of the People’s Republic of China (SAC). (1991). “Metallic materials—Standard test method for the Young’s modulus, shear modulus and Poisson’s ratio (dynamic method).”, China Standard Press, Beijing.
Standardization Administration of the People’s Republic of China (SAC). (2002). “Metallic materials—Tensile testing at ambient temperature.”, China Standard Press, Beijing.
Standardization Administration of the People’s Republic of China (SAC). (2006a). “Carbon structural steel.”, China Standard Press, Beijing.
Standardization Administration of the People’s Republic of China (SAC). (2006b). “Metallic materials—Tensile testing at elevated temperature.”, China Standard Press, Beijing.
Standardization Administration of the People’s Republic of China (SAC). (2008). “High strength low alloy structural steel.”, China Standard Press, Beijing.
Standards Australia (SA). (1998). “Steel structures.” AS 4100, Sydney, Australia.
Standards Australia (SA). (2004). “Structural steel welding Part 4: Welding of high strength quenched and tempered steels.” AS/NZS 1554.4:2004, Sydney, Australia.
Tan, W. (2000). “Experiments and research of steel material properties at elevated temperature.” Indust. Constr., 30(10), 61–63, 67 (in Chinese).
Twilt, L. (1988). “Strength and deformation properties of steel at elevated temperatures.” Fire Saf. J., 13(1), 9–15.
Wang, W. Y., Li, G. Q., and Dai, G. X. (2010). “Fire-resistance performance of high-strength-steel H shaped columns under the axial compression.” J. Chongqing Univ., 33(10), 76–82 (in Chinese).
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: May 6, 2011
Accepted: May 30, 2012
Published online: Aug 29, 2012
Published in print: Feb 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.