Mechanical Property Characterization of Fiber-Reinforced Polymer Wood-Polypropylene Composite Panels Manufactured Using a Double Belt Pressing Technology
Publication: Journal of Materials in Civil Engineering
Volume 24, Issue 9
Abstract
A novel manufacturing process for wood-polypropylene composite (WPC) panels reinforced with fiber-reinforced polymer (FRP) sheets was implemented using a double belt pressing technology. FRP sheets were placed on both sides of the WPC agglomerates during fabrication, which resulted in increased productivity and reduced thermal stresses compared with secondary bonding processes. Significant improvements in the mechanical properties of the FRP reinforced sheet panels were found during flexural and tensile tests on the coupon level. Even with addition of only one layer of FRP reinforcement on both sides of a WPC panel, the flexural modulus and strength increased by a factor of 2.6 and 3.8, respectively. Furthermore, the flexural and tensile properties of the WPC material considered in this study were found to be superior compared with the properties of an extruded WPC material. The changes in the flexural modulus of the FRP reinforced WPC panels with respect to the number of FRP layers were predicted using a model based on moment-curvature analysis.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research project was carried out under Contract no. DTFH61-06-D-00022. The authors are grateful to the United States Federal Highway Administration (FHWA) for the financial support.
References
Alvarez-Valencia, D., Dagher, H. J., Davids, W. G., Lopez-Anido, R., and Gardner, D. J. (2010). “Structural performance of wood plastic composite (WPC) sheet piling.” J. Mater. Civ. Eng., 22(12), 1235–1243.
ASTM. (2003). “Standard test method for tensile properties of plastics.”, New York.
ASTM. (2007). “Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials.”, New York.
Behravesh, A. H., Aghdam, A. Z., and Soury, E. (2010). “Experimental investigation of injection molding of wood/plastics composites.” J. Reinf. Plast. Compos., 29(3), 456–465.
Clemons, C. (2008). “Raw materials for wood-polymer composites.” Wood-polymer composites, Niska, K. O., and Sain, M., ed., Woodhead Publishing Limited, Cambridge, UK.
Davidow, S. A., and Fridley, K. J. (2003). “Development of design values for wood-plastic composite materials.” J. Mater. Civ. Eng., 15(5), 415–418.
Deng, S., and Tang, Y. (2010). “Increasing load-bearing capacity of wood-plastic composites by sandwiching natural and glass fabrics.” J. Reinf. Plast. Compos., 29(20), 3133–3148.
Dura, M. J. (2005). “Behavior of hybrid wood plastic composite-fiber reinforced polymer structural members for use in sustained loading applications.” Master’s thesis, Univ. of Maine, Orono, ME.
Grande, C., and Torres, F. G. (2005). “Investigation of fiber organization and damage during single screw extrusion of natural fiber reinforced thermoplastics.” Adv. Polymer Tech., 24(2), 145–156.
Jiang, L., Wolcott, M. P., Zhang, J., and Englund, K. (2007). “Flexural properties of surface reinforced wood/plastic deck board.” Poly. Eng. Sci., 47(3), 281–288.
Klyosov, A. (2007). Wood-plastic composites, John Wiley & Sons, Hoboken, NJ.
Lu, J. Z., Wu, Q., and Negulescu, I. I. (2005). “Wood-fiber/high-density-polyethylene composites: couopling agent performance.” J. Appl. Polym. Sci., 96(1), 93–102.
Naghipour, M., Nematzadeh, M., and Yahyazadeh, Q. (2011). “Analytical and experimental study on flexural performance of WPC—FRP beams.” Construct. Build. Mater., 25(2), 829–837.
Panthapulakkal, S., and Sain, M. (2006). “Injection molded wheat straw and corn stem filled polypropylene composites.” J. Poly. Environ., 14(3), 265–272.
Raj, R. G., Kokta, B. V., Grouleau, G., and Daneault, C. (1990). “Influence of coupling agents on mechanical properties of composites containing cellulosic fillers.” Poly. Plast. Technol. Eng., 29(4), 339–353.
Stark, N. M. (2006). “Effect of weathering cycle and manufacturing method on performance of wood flour and high-density polyethylene composites.” J. Appl. Polym. Sci., 100(4), 3131–3140.
Tamrakar, S., and Lopez-Anido, R. A. (2011). “Water absorption of wood polypropylene composite sheet piles and its influence on mechanical properties.” Construct. Build. Mater., 25(10), 3977–3988.
Tamrakar, S., Lopez-Anido, R. A., Kiziltas, A., and Gardner, D. J. (2011). “Time and temperature dependent response of a wood-polypropylene composite.” Composites Part A., 42(7), 834–842.
Thermofix Technology Center. (2011). Development of new products designed for R&D, test and prototype runs small scale and pilot production, Thermofix Technology Center, Mühlhausen, Germany.
Yam, K. L., Gogoi, B. K., Lai, C. C., and Selke, S. E. (1990). “Composites from compounding wood fibers with recycled high density polyethylene.” Poly. Eng. Sci., 30(11), 693–699.
Ye, L., Lu, M., and Mai, Y. (2002). “Thermal de-consolidation of thermoplastic matrix composites—I. Growth of voids.” Compos. Sci. Technol., 62(16), 2121–2130.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Aug 20, 2011
Accepted: Jan 25, 2012
Published online: Jan 28, 2012
Published in print: Sep 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.