Influences of Polymer Modification and Exposure Conditions on Chloride Permeability of Cement Mortars and Composites
Publication: Journal of Materials in Civil Engineering
Volume 24, Issue 2
Abstract
On the basis of laboratory investigations, this paper presents the chloride penetration and diffusion over different exposure conditions of three commercial polymer-modified mortars, styrene-butadiene rubber (SBR), polyacrylic ester (PAE), and vinyl acetateethylene (VAE), and unmodified conventional mortar mix and composites. The results indicated that within 15% of polymer addition in cement mortars, there was a substantial decrease in chloride penetration. The diffusion coefficients of chloride ions estimated from the simplified linear error function–based (SLEM), Newton-Raphson, and least-squares fit methods showed increasing value coefficients with the increasing age of specimens or cycles of exposure. The results also revealed that at 15 and 40 cycles of wetting and drying, the cement mortars modified with VAE exhibited a much superior quality in chloride penetration than SBR- or PAE-modified mortars.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abramowitz, M., and Stegun, I. A. (1965). Handbook of mathematical functions with formulas, graphs and mathematical tables, National Bureau of Standards, Washington, DC.
Balonis, M., Lothenbach, B., Saout, G. L., and Glasser, F. P. (2010). “Impact of chloride on the mineralogy of hydrated portland cement systems.” Cem. Concr. Res., 40(7), 1009–1022.
Berman, H. A. (1972). “Determination of chloride in hardeded portland cement paste, mortar and cement.” J. Mater., 7(3), 330–335.
Cabrera, J. G., and Al-Hasan, A. S. (1997). “Performance properties of concrete repair materials.” Constr. Build. Mater., 11(5–6), 283–290.
Do, J., and Soh, Y. (2003). “Performance of polymer-modified self-leveling mortars with high polymer-cement ratio for floor finishing.” Cem. Concr. Res., 33(10), 1497–1505.
Duffó, G. S., Farina, S. B., Schulz, F. M., and Marotta, F. (2010). “Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes.” J. Nucl. Mater., 405(3), 274–279.
El-Mekkawi, S. A., Ismail, I. M., El-Attar, M. M., Fahmy, A. A., and Mohammed, S. S. (2011). “Utilization of black liquor as concrete admixture and set retarder aid.” J. Advertising Res., 2(2), 163–169.
Gjorv, O. E. (1975). “Control of steel corrosion in concrete sea structures.” Corros. Met. Concr., 49, 1–9.
Grantham, M. G., Herts, B., and Broomfield, J. (1997). “The use of linear polarisation corrosion rate measurements in aiding rehabilitation options for the deck slabs of a reinforced concrete underground car park.” Constr. Build. Mater., 11(4), 215–224.
Huai-shuai, S., and Yu-pu, S. (2008). “Behavior of air-entrained concrete under the compression with constant confined stress after freeze-thaw cycles.” Cem. Concr. Compos., 30(9), 854–860.
Hwang, E.-H., and Ko, Y. S. (2008). “Comparison of mechanical and physical properties of SBR-polymer modified mortars using recycled waste materials.” J. Ind. Eng. Chem. (Amsterdam, Neth.), 14(5), 644–650.
Hwang, E.-H., Ko, Y. S., and Jeon, J.-K. (2008). “Effect of polymer cement modifiers on mechanical and physical properties of polymer-modified mortar using recycled artificial marble waste fine aggregate.” J. Ind. Eng. Chem. (Amsterdam, Neth.), 14(2), 265–271.
Jenni, A., Zurbriggen, R., Holzer, L., and Herwegh, M. (2006). “Changes in microstructures and physical properties of polymer-modified mortars during wet storage.” Cem. Concr. Res., 36(1), 79–90.
Jones, K., and Hoeppner, D. W. (2006). “Prior corrosion and fatigue of 2024-T3 aluminum alloy.” Corros. Sci., 48(10), 3109–3122.
Kenai, S., and Bahar, R. (2003). “Evaluation and repair of Algiers new airport building.” Cem. Concr. Compos., 25(6), 633–641.
Kramberger, T., and Žerovnik, J. (2008). “A contribution to environmentally friendly winter road maintenance: Optimizing road de-icing.” Transp. Res. Part D, 13(5), 340–346.
Kuo, W.-Y., Huang, J.-S., and Lin, C.-H. (2006). “Effects of organo-modified montmorillonite on strengths and permeability of cement mortars.” Cem. Concr. Res., 36(5), 886–895.
Malik, A. U., Andijani, I., Al-Moaili, F., and Ozair, G. (2004). “Studies on the performance of migratory corrosion inhibitors in protection of rebar concrete in Gulf seawater environment.” Cem. Concr. Compos., 26(3), 235–242.
Medeiros, M. H. F., Helene, P., and Selmo, S. (2009). “Influence of EVA and acrylate polymers on some mechanical properties of cementitious repair mortars.” Constr. Build. Mater., 23(7), 2527–2533.
Narasimhan, H., and Chew, M. Y. L. (2009). “Integration of durability with structural design: An optimal life cycle cost based design procedure for reinforced concrete structures.” Constr. Build. Mater., 23(2), 918–929.
Ngala, V. T., Page, C. L., and Page, M. M. (2002). “Corrosion inhibitor systems for remedial treatment of reinforced concrete. Part 1: Calcium nitrite.” Corros. Sci., 44(9), 2073–2087.
Pruckner, F., Theiner, J., Eri, J., and Nauer, G. E. (1996). “In-situ monitoring of the efficiency of the cathodic protection of reinforced concrete by electrochemical impedance spectroscopy.” Electrochim. Acta, 41(7/8), 1233–1238.
Reis, J. M. L. (2009). “Mechanical characterization of polymer mortars exposed to degradation solutions.” Constr. Build. Mater., 23(11), 3328–3331.
Stampino, P. G., Zampori, L., Dotelli, G., Meloni, P., Sora, I. N., and Pelosato, R. (2009). “Use of admixtures in organic-contaminated cement-clay pastes.” J. Hazard. Mater., 161(2–3), 862–870.
Suryavanshi, A. K., Swamy, R. N., and Cardew, G. E. (2002). “Estimation of diffusion coefficient for chloride for chloride ion penetration intro structural concrete.” ACI Mater. J., 99(5), 441–449.
Švegl, F., Šuput-Strupi, J., Škrlep, L., and Kalcher, K. (2008). “The influence of aminosilanes on macroscopic properties of cement paste.” Cem. Concr. Res., 38(7), 945–954.
Swamy, R. N. (1994). “Design: The key to concrete material durability and structural integrity.” Proc., Int. Conf. on Reinforced Concrete Materials in Hot Climates, Alain, UAE, 3–36.
Swamy, R. N., Hamada, H., Fukute, T., Tanikawa, S., and Laiw, J. C. (1995). “Chloride penetration into concrete incorporating mineral admixtures or protected with surface coating material under chloride environments, concrete under severe conditions.” Concrete under severe conditions: Environment and loading, Vol. 2, Spon, London, 935–944.
Talero, R., et al. (2010). “Comparative and semi-quantitative XRD analysis of Friedel’s salt originating from pozzolan and portland cement.” Constr. Build. Mater., 25(5), 2370–2380, .
Wallbank, E. J. (1989). “The performance of concrete in bridges: A survey of 200 highway bridges.” Document no., Her Majesty’s Stationary Office, London.
Yang, Z., Shi, X., Creighton, A. T., and Peterson, M. M. (2009). “Effect of styrene-butadiene rubber latex on the chloride permeability and microstructure of portland cement mortar.” Constr. Build. Mater., 23(6), 2283–2290.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Feb 15, 2011
Accepted: Aug 17, 2011
Published online: Aug 19, 2011
Published in print: Feb 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.