Improvement on SIFCON Performance by Fiber Orientation and High-Volume Mineral Admixtures
Publication: Journal of Materials in Civil Engineering
Volume 22, Issue 11
Abstract
The effects of steel fiber alignment and high-volume mineral admixture replacement [Class C fly ash (FA) and ground granulated blast furnace slag (GGBS)] on the mechanical properties of SIFCON (Slurry Infiltrated Fiber Concrete) have been investigated. Ordinary portland cement was replaced with 50% (by weight) FA or GGBS in SIFCON slurries, and two different steel fiber alignments (random and oriented in one direction) were used. Test results showed that FA and GGBS replacement positively affected mechanical properties (compressive and flexural strength and fracture energy) and fiber alignment is an important factor for superior performance. Binary combination of improved matrices (low water/binder ratio and mineral admixture replacement) and proper fiber orientation enhances mechanical performance, particularly flexural properties of SIFCON. Flexural strength and fracture energy of this composite are 138 MPa and 195,815 N/m, respectively. Scanning electron microscope investigations revealed tobermorite-like structures having different morphology such as foiled, fibrous, and honeycomb with low Ca/Si ratio after autoclaving. Mercury porosimeter tests showed the decreasing of total porosity and pore refinement with FA or GGBS.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study is a part of the project supported by the Scientific and Technological Research Council of Turkey (TÜBİTAK, Project No: UNSPECIFIED106M283). The writers gratefully acknowledge TÜBİTAK. In addition, the writers acknowledge Mr. Osman TEZEL from BASF, Mr. Okan TOĞRUL from Draco, Mr. Hakan ŞENVARDARLI from Karçimsa, and Mrs. Nagehan HALDENBİLEN from Modern Beton for their material support.
References
Aldea, C. M., Young, F., Wang, K., and Shah, S. P. (2000). “Effects of curing conditions on properties of concrete using slag replacement.” Cem. Concr. Res., 30, 465–472.
Bilodeau, A., Sivasundaram, V., Painter, K. E., and Malhotra, V. M. (1994). “Durability of concrete incorporating high volumes fly ash from sources in the U.S.A.” ACI Mater J., 91, 3–12.
Doğan, E. (2000). “Retrofit of non-ductile reinforced concrete frames using high performance fiber reinforced composites.” Ph.D. thesis, Civil Engineering, North Carolina State Univ., Raleigh, N.C.
EFNARC (2002). Specification and guidelines for self-compacting concrete, European Federation for Specialist Construction Chemicals and Concrete Systems, Norfolk, U.K.
Glasser, F. P., and Hong, S. Y. (2003). “Thermal treatment of C-S-H gel at 1 bar pressure up to .” Cem. Concr. Res., 33, 271–279.
Homrich, J. R., and Naaman, A. E. (1987). “Stress-strain properties of SIFCON in compression.” Fiber reinforced concrete properties and applications, ACI, SP-105, American Concrete Institute, Detroit, 244–251.
Lankard, D. R. (1984). “Properties, applications: Slurry infiltrated fiber concrete (SIFCON).” Concr. Int., 6(12), 44–47.
Maeder, U., Gamboa, I. L., Chaigmon, J., and Lombard, J. P. (2004). “Ceracem, a new high performance concrete: Characterizations and applications.” Proc., Int. Symp. on Ultra High Performance Concrete, Kassel Univ. Press, Kassel, Germany, 59–68.
Malhotra, V. M., Mehta, P. K. (2002). “High-performance, high-volume fly ash concrete.” Supplementary cementing materials for sustainable development Inc., Marquardt Printing, Ottawa.
Mehta, P. K., and Monteiro, J. M. P. (2006). Concrete (microstructure, properties, and materials), 3rd Ed., McGraw-Hill, New York.
Murakami, H., and Zeng, J. Y. (1998). “Experimental and analytical study of SIMCON tension members.” Mech. Mater., 28, 181–195.
Naaman, A. E., and Homrich, J. R. (1989). “Tensile stress-strain properties of SIFCON.” ACI Mater. J., 3, 244–251.
Naaman, A. E., Otter, D., and Najm, H. (1992). “Elastic modulus of SIFCON in tension and compression.” ACI Mater. J., 6, 603–613.
Naaman, A. E., Wight, J. K., and Abdou, H. (1987). “SIFCON connections for seismic resistant frames.” Concr. Int., 11, 34–39.
Neville, A. M. (1995). Properties of concrete, Longman, New York.
Odler, I. (1997). “Hydration, setting and hardening of Portland cement.” Lea’s chemistry of cement and concrete, P. C. Hewlett, ed., Butterworth-Heinemann, Oxford, U.K., 288–289.
RILEM50-FMC Committee of Fracture Mechanics of Concrete. (1985). “Determination of fracture energy of mortar and concrete by means of three-point bend tests on notched beams.” Mater. Struct., 18, 285–290.
Scrivener, K. L. (2004). “Backscattered electron imaging of cementitious microstructures: Understanding and quantification.” Cem. Concr. Compos., 26, 935–945.
Shi, C., and Hu, S. (2003). “Cementitious properties of ladle slag fines under autoclave curing conditions.” Cement Concr. Res., 33, 1851–1856.
Sonebi, M., Svermova, L., and Bartos, P. J. M. (2004). “Factorial design of cement slurries containing limestone powder for self-consolidating slurry-infiltrated fiber concrete.” ACI Mater. J., 2, 136–145.
Sonebi, M., Svermova, L., and Bartos, P. J. M. (2005). “Statistical modeling of cement slurries for self-compacting SIFCON containing silica fume.” Mater. Struct., 38, 79–86.
Stiel, T., Karihaloo, B. L., and Fehling, E. (2004). “Effect of casting direction on the mechanical properties of CARDIFRC.” Proc., Int. Symp. on Ultra High Performance Concrete, Kassel Univ. Press, Kassel, Germany, 481–493.
Wood, B. T. (2000). “Use of slurry infiltrated fiber concrete (SIFCON) in hinge regions for earthquake resistant structures.” Ph.D. thesis, Civil Engineering, North Carolina State Univ., Raleigh, N.C.
Yan, A., Wu, K., and Zhang, X. (2002). “A quantitative study on the surface crack pattern of concrete with high content of steel fiber.” Cem. Concr. Res., 32, 1371–1375.
Yang, Q., Zhang, S., Huang, S., and He, Y. (2000). “Effect of ground quartz sand on properties of high-strength concrete in the steam-autoclaved curing.” Cem. Concr. Res., 30, 1993–1998.
Yazıcı, H., Yiğiter, H., Aydın, S., and Baradan, B. (2006). “Autoclaved SIFCON with high volume Class C fly ash binder phase.” Cem. Concr. Res., 36, 481–486.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Oct 1, 2009
Accepted: Apr 29, 2010
Published online: May 6, 2010
Published in print: Nov 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.