Comparison of Mechanical Properties for Polymer Concrete with Different Types of Filler
Publication: Journal of Materials in Civil Engineering
Volume 22, Issue 7
Abstract
Sustained research and development work on the utilization of waste (fly ash and silica fume) for various productive uses have been carried out. In the construction industry, major attention has been devoted to the use of fly ash and silica fume in concrete as addition to or as cement replacement. The utilization of a solid waste, fly ash and silica fume, in polymer concrete was reported in this paper including the effects on the compressive strength, flexural strength, and split tensile strength. The results show the influence of fly ash and silica fume content on the mechanical properties of polymer concrete with epoxy resin. The fillers improved the mechanical characteristics of polymer concrete compared to that of polymer concrete without filler: the compressive strength of polymer concrete with fly ash content was favorably influenced by the filler compound to polymer concrete with silica fume.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abdel-Fattah, H., and El-Hawary, M. (1999). “Flexural behavior of polymer concrete.” Constr. Build. Mater., 13, 253–262.
Abul Bari, H. A., Tabet Abid, R., and Mohammad, A. H. (2008). “Fume silica base grease.” J. Appl. Sci., 8(4), 687–691.
ASTM. (2007). ASTM C618, ⟨http://www.undeerc.org/carrc⟩ (May 25, 2007).
Bărbuţă, M. (2007). “Components compatibility to flexible concrete.” Proc., Symp. Pre-cast Concrete, Editura UT Press, Cluj Napoca, Romania, 209–218 (in Romanian).
Bărbuţă, M., and Harja, M. (2009). “Polymer concrete.” Materials used for obtaining polymer concrete, Politehnium, Iasi, Romania, 39–51.
Bărbuţă, M., and Lepădatu, D. (2008). “Mechanical characteristics investigation of polymer concrete using mixture design of experiments and response surface method.” J. Appl. Sci., 8, 2242–2249.
Bărbuţă, M., Lepădatu, D., and Mihai, P. (2008). “Mixture optimization of polymer concrete with silica fume.” Proc., Int. Conf. Constructions 2008, Editura Napoca Star, Cluj-Napoca, Romania, 11–22.
Blaga, A., and Beaudoin, J. J. (1985). “Polymer concrete.” Canadian building digest, CBD-242, NRC-IRC Publication, Canada.
Byung-Wan, J., Seung-Kook, P., and Cheol-Hwan, K. (2006). “Mechanical properties of polyester polymer concrete using recycled polyethylene terephthalate.” ACI Struct. J., Mar./Apr., 3–4.
Criado, M., Fernandez-Jimenez, A., and Palomo, A. (2007). “Alkali activation of fly ash: Effect of ratio. Part I: FTIR study.” Microporous Mesoporous Mater., 106, 180–191.
de Souza Almeida, A. E. F., and Sichieri, E. P. (2006). “Thermogravimetric analyses and mineralogical study of polymer modified mortar with silica fume.” Mater. Res., 9(3), 1–15.
Denver, J. S. J., Provis, J. L., Duxson, P., and Lukey, G. C. (2007). “Reaction mechanism in the geopolymeric conversion of inorganic waste to useful products.” J. Hazard. Mater., A139, 506–513.
Erol, M., Kucukbayrak, S., and Ersoy-Mericboyu, A. (2007). “Characterization of coal fly ash for possible utilization in glass production.” Fuel, 86, 706–714.
Fowler, D. W. (1999). “Polymers in concrete: A vision for 21st century.” Cem. Concr. Compos., 21, 449–452.
Harja, M., Bărbuţă, M., Rusu, L., and Apostolescu, N. (2008). “Utilization of coal fly ash from power plants: I. Ash characterization.” J. Environ. Manage., 7, 289–294.
Khale, D., and Chaudhary, R. (2007). “Mechanism of geopolymerization and factors influencing its development: A review.” J. Mater. Sci., 42, 729–746.
Muthukumar, M., Mohan, D., and Rajendran, M. (2003). “Optimization of mix proportions of mineral aggregates using Box Behnken design of experiments.” Cem. Concr. Compos., 25, 751–758.
Ohama, Y. (1996). “Polymers-based materials for repair and improved durability: Japanese experience.” Constr. Build. Mater., 10, 77–82.
Pardo, A., Rz-Maribona, I., Urreta, J., San Jose, J. T., and Muguerza, A. (1995). “Influence of dosage and temperature on mechanical properties of polymer concrete.” VII Int. Congress of Polymers in Concrete, ICPIC’95, D. Van Gemert, ed., Katholieke Universiteit Leuven y Technological Institute–K VIV, Oostende, Belgium, 199–205.
Ramirez, J. L., and San-Jose, J. T. (2001). “Predictability of structural calculations values in a 100 MPa polymeric concrete.” Proc., 10th Int. Congress on Polymers in Concrete. Polymers in Concrete in the Third Millennium: Challenges and Opportunities (ICPIC 2001) (CD-ROM), Honolulu.
Rangan, B. V. (2008). “Fly ash-based geopolymer concrete.” Research Rep. No. GC 4, Eng. Faculty Curtin Univ. Techn., Perth, Australia.
Rebeiz, K. S., Serhal, S. P., and Craft, A. P. (2004). “Properties of polymer concrete using fly ash.” J. Mater. Civ. Eng., 16(1), 15–19.
Reis, J. M. L. (2006). “Fracture and flexural characterization of natural fiber-reinforced polymer concrete.” Constr. Build. Mater., 20, 673–678.
Reis, J. M. L., and Ferreira, A. J. M. (2004). “Assessment of fracture properties of epoxy polymer concrete reinforced with short carbon and glass fibers.” Constr. Build. Mater., 18, 523–528.
San-José, J. T. (2006). “Mechanical properties in resin polyester concrete, application to reinforced beams “.” Sci. Eng. Compos. Mater., 13(4), 271–282.
San-José, J. T., and Frias, M. (2007). “High performance polymer concrete.” Mater. Constr., 57(286), 29–39.
San-José, J. T., and Manso, J. M. (2006). “Fiber-reinforced polymer bars embedded in a resin concrete: Study of both materials and their bond behavior.” Polym. Compos., 27(3), 315–322.
San-José, J. T., Vegas, I., and Ferreira, A. (2005). “Reinforced polymer concrete: Physical properties of the matrix and static/dynamic bond behavior.” Cem. Concr. Compos., 27(9–10), 934–944.
San-José, J. T., Vegas, I. J., and Frías, M. (2008). “Mechanical expectations of a high performance concrete based on a polymer binder and reinforced with non-metallic rebars.” Constr. Build. Mater., 22, 2031–2041.
Srivastava, V. K., and Shembekar, J. (1990). “Tensile and fracture properties of epoxy resin filled with fly ash particles.” J. Mater. Sci., 25(8), 3513–3516.
Varughese, K. T., and Chaturvedi, B. K. (1996). “Fly ash as fine aggregate in polyester based polymer concrete.” Cem. Concr. Compos., 18, 105–108.
Information & Authors
Information
Published In
Copyright
© 2010 ASCE.
History
Received: Sep 22, 2008
Accepted: Nov 23, 2009
Published online: Nov 25, 2009
Published in print: Jul 2010
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.