Effects of Lifting Force on Bed Topography and Bed-Surface Sediment Size in Channel Bend
Publication: Journal of Hydraulic Engineering
Volume 137, Issue 9
Abstract
In bed-load sediment transport, the lifting force plays an important role in reducing the friction between sediment particles and the bed surface, and it makes particle transportation by the shear force easier. Because the lifting force is related to vorticity, a three-dimensional (3D) numerical model incorporating large eddy simulations was applied to simulate the vorticity field in a channel bend. The results show that the distribution of vorticity is highly nonuniform, and it can lead to significant variations in lifting force and bed-load sediment transport per unit width in a channel bend. Relevant theories are modified on the basis of physical reasoning and then incorporated into numerical models to investigate the lifting-force effects on the bed topography and bed-surface sediment size gradation in a channel bend. With the lifting-force effects considered, it is shown that the errors in simulated bed topography can be reduced by approximately 40% and in bed-surface sediment size by 50%.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The computer resources and laboratory facilities provided for this research by National Center for High-Performance Computing and Hydrotech Research Institute of National Taiwan University are gratefully acknowledged. The authors would like to express their sincere gratitude to Professors D. L. Young, A. Y. Kuo, and K. C. Yeh for their valuable comments.
References
Ahmed, A. K., and Chaudhry, M. H. (1998). “Comparison of coupled and semicoupled numerical models for alluvial channels.” J. Hydraul. Eng., 124(8), 794–802.
Bagnold, R. A. (1973). “The nature of saltation and of bed-load transport in water.” Proc. R. Soc. London, Ser. A, A332, 473–504.
Chang, H. K. (1997). “Simulation of bed topography and flow field in channel bend.” M.S. thesis, Dept. of Civil Eng., National Taiwan Univ., Taipei, Taiwan (in Chinese).
Chepil, W. S. (1961). “The use of spheres to measure lift and drag on wind-eroded soil grains.” Soil Sci. Soc. Am. Proc., 25(5), 343–345.
Dandy, D. S., and Dwyer, H. A. (1990). “Sphere in shear flow at finite Reynolds number: Effect of shear on particle lift, drag, and heat transfer.” J. Fluid Mech., 216, 381–410.
de Vriend (1981). “Velocity redistribution in curved rectangular channels.” J. Fluid Mech., 107, 423–439.
Egiazaroff, I. V. (1965). “Calculation of nonuniform sediment concentrations.” J. Hydraul. Div., 91(HY4), 225–247.
Einstein, H. A. (1950). “The bed-load function for sediment transportation in open channel flows.” Technical Bulletin No. 1026, U. S. Dept. of Agriculture, Soil Conservation Service, Washington, DC.
Einstein, H. A., and El-Sammi, E. A. (1942). “Formula for the transportation of bed-load.” Trans. Am. Soc. Civ. Eng., 107.
Fernandez Luque, R., and van Beek, R. (1976). “Erosion and transport of bed-load sediment.” J. Hydraul. Res., 14(2), 127–144.
Gordan, R., Carmichael, J. B., and Isackson, F. J. (1972). “Saltation of plastic balls in a one-dimension flume.” Water Resour. Res., 8(2), 444–459.
Hsiao, G. H. (1998). “Simulation of bed topography and sediment gradation in channel bend.” M.S. thesis, Dept. of Civil Eng., National Taiwan Univ., Taipei, Taiwan (in Chinese).
Jang, J. H. (2005). “Effect of lifting force on bed topography and bed-surface sediment size in channel bend.” Ph.D. thesis, Dept. of Civil Eng., National Taiwan Univ., Taipei, Taiwan.
Jang, J. H., Ho, H. Y., and Yen, C. L. (2006). “Effect of lift on bed-surface sediment size distribution in channel bend.” J. Chin. Inst. Eng., 29(4), 565–579.
Kurose, R., and Komori, S. (1999). “Drag and lift forces on a rotating sphere in a linear shear flow.” J. Fluid Mech., 384, 183–206.
Lee, H. Y., and Hsu, I. S. (1994). “Investigation of saltating particle motions.” J. Hydraul. Eng., 120(7), 831–845.
Lee, H. Y., Lin, Y. T., You, J. Y., and Wang, H. W. (2006). “On three-dimensional continuous saltating process of sediment particles near the channel bed.” J. Hydraul. Res., 44(3), 374–389.
Lee, H. Y., You, J. Y., and Lin, Y. T. (2002). “Continuous saltating process of multiple sediment particle.” J. Hydraul. Eng., 128(4), 443–450.
Legendre, D., and Magnaudet, J. (1997). “A note on the lift force on a spherical bubble or drop in a low-Reynolds-number shear flow.” Phys. Fluids, 9(11), 3572–3574.
Leschziner, M. A., and Rodi, W. (1979). “Calculation of strongly curved open channel flow.” J. Hydraul. Div., 105(10), 1297–1314.
MacCormack, R. W. (1969). “The effect of viscosity in hypervelocity impact cratering.” AIAA Paper No. 69-354, Reston, VA.
Mei, R. (1992). “Approximate expression for the shear lift force on a spherical particle at finite Reynolds number.” Int. J. Multiphase Flow, 18(1), 145–147.
Meriam, J. L., and Kraige, L. G. (1993). Engineering dynamics, Vol. 2, Appendix D, 3rd Ed., Wiley, New York, 703–704.
Murphy, P. J., and Hooshiari, H. (1982). “Saltation in water dynamics.” J. Hydraul. Div., 108(11), 1251–1267.
Poesio, P., Ooms, G., and Cate, A. T. (2006). “Interaction and collisions between particles in a linear shear flow near a wall at low Reynolds number.” J. Fluid Mech., 555, 113–130.
Rozovskii, I. L. (1961). Flow of water in bends of open channels. Trans. Y. Prushansky. Academy of Sciences of Ukrainian SSR, Kiev, Ukraine.
Saffman, P. G. (1965). “The lift on a small sphere in slow shear flow.” J. Fluid Mech., 22, 385–400.
Shields, A. (1936). Anwendung der Ähnlichkeitsmechanik und der Turbulenzforchung auf die Geschiebebewegung. Trans. W. P. Ott and J. C. van Uchelen. Mitteilungen der Preussiischen Versuchsanstalt fur Wasserbau und Schiffhau, Berlin.
Smagorinsky, J. (1963). “General circulation experiments with primitive equation.” Mon. Weather Rev., 91, 99–154.
Tseng, M. H. (1994). “Numerical simulation of flow and scour around bridge pier.” Ph.D. thesis, Dept. of Civil Eng., National Taiwan Univ., Taipei, Taiwan (in Chinese).
Tsorng, S. J. (1996). “Simulation of three dimensional flow field in channel bend.” M.S. thesis, Dept. of Civil Eng., National Taiwan Univ., Taipei, Taiwan (in Chinese).
van Rijn, L. C. (1984). “Sediment transport, Part I: Bed load transport.” J. Hydraul. Eng., 110(10), 1431–1456.
White, B. R., and Schulz, J. C. (1964). “Magnus effect in saltation.” J. Fluid Mech., 81, 497–512.
Wiberg, P. L., and Smith, J. D. (1985). “A theoretical model for saltating grains in water.” J. Geophys. Res., 90(C4), 7341–7354.
Yalin, M. S. (1972). Mechanics of sediment transport, Pergamon, Oxford, UK, 322–338.
Yen, B. C. (1965). “Characteristics of subcritical flow in a meandering channel.” Ph.D. thesis, Univ. of Iowa, Iowa City, IA
Yen, C. L. (1967). “Bed configuration and characteristics of subcritical flow in a meandering channel.” Ph.D. thesis, Univ. of Iowa, Iowa City, IA
Yen, C. L., and Lin, Y. L. (1997). “Variations of bed surface sediment size in a channel bend.” Water Air Soil Pollut., 99(1–4), 81–88.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Jan 5, 2009
Accepted: Feb 4, 2011
Published online: Feb 8, 2011
Published in print: Sep 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.