Centrifuge Modeling of Shallow Foundation Lateral Disconnection to Reduce Seismic Vulnerability
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 148, Issue 2
Abstract
An innovative yet extremely simple approach to reduce the seismic vulnerability of existing buildings on shallow foundations is to remove the lateral contact between the embedded foundation and the surrounding soil. This paper compares the dynamic response of two identical one-degree-of-freedom reduced-scale model sway frames tested in a geotechnical centrifuge. One of the models was founded on fully embedded shallow strip footings, whereas the foundations of the other were disconnected from the soil laterally. Both models were constructed in dry medium density sand whose strength and small strain shear stiffness profiles were obtained by cone penetration and air hammer tests carried out in flight. Various tools were used to monitor the displacements and accelerations both in the structure and in the soil, including micro-electro-mechanical systems (MEMS) accelerometers, piezoelectric accelerometers, LVDTs, and a high-frequency camera. The experimental results demonstrate that the lateral disconnection of the foundation from the adjacent soil significantly reduces the foundation translational and rotational stiffness, which results in a larger predominant period of the structure and a reduction of the absolute floor accelerations obtained for different sinusoidal input signals. The lateral disconnection also mitigates floor drift and story shear forces. The trade-off is the lower radiative damping observed for the laterally disconnected foundation, which results in a larger number of post-earthquake oscillations of the structure.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
Alessandro Fusco and Domenico Gaudio provided assistance and advice to the first author during preparation of the centrifuge test. We are also grateful to Prof. Gopal Madabhushi and to all the technicians of the Schofield Center for their invaluable help.
References
Boussinesq, J. 1885. Application des potentiels à l’ètude de l’equilibre et du mouvement des solides elastiques. Paris: Gauthier-Villard.
CEN (European Committee for Standardization). 2004. Eurocode 8: Design of structures for earthquake resistance. BS EN 1998-1. Brussels, Belgium: CEN.
Charles, J. A., and H. D. Skinner. 2004. “Settlement and tilt of low-rise buildings.” Proc. Inst. Civ. Eng. Geotech. Eng. 157 (2): 65–75. https://doi.org/10.1680/geng.2004.157.2.65.
Cremer, C., A. Pecker, and L. Davenne. 2001. “Cyclic macro-element for soil-structure interaction: Material and geometrical non-linearities.” Int. J. Numer. Anal. Methods Geomech. 25 (13): 1257–1284. https://doi.org/10.1002/nag.175.
Flavigny, E., J. Desrues, and B. Palayer. 1990. “Le sable d’Hostun.” Rev. Fr. Géotech. 53: 67–70. https://doi.org/10.1051/geotech/1990053067.
Flora, A., D. Lombardi, V. Nappa, and E. Bilotta. 2018. “Numerical analyses of the effectiveness of soft barriers into the soil for the mitigation of seismic risk.” J. Earthquake Eng. 22 (1): 63–93. https://doi.org/10.1080/13632469.2016.1217802.
Gajan, S., and B. Kutter. 2008. “Capacity, settlement, and energy dissipation of shallow footings subjected to rocking.” J. Geotech. Geoenviron. 134 (8): 1129–1141. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:8(1129).
Gazetas, G. 1991. “Formulas and charts for impedances of surface and embedded foundations.” J. Geotech. Eng. 117 (9): 1363–1381. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:9(1363).
Gazetas, G. 2015. “4th Ishihara lecture: Soil–foundation–structure systems beyond conventional seismic failure thresholds.” Soil Dyn. Earthquake Eng. 68 (Jan): 23–39. https://doi.org/10.1016/j.soildyn.2014.09.012.
Gazetas, G., and J. L. Tassoulas. 1987. “Horizontal stiffness of arbitrarily shaped embedded foundations.” J. Geotech. Eng. 113 (5): 440–457. https://doi.org/10.1061/(ASCE)0733-9410(1987)113:5(440).
Gerolymos, N., and G. Gazetas. 2006. “Winkler model for lateral response of rigid caisson foundations in linear soil.” Soil Dyn. Earthquake Eng. 26 (5): 347–361. https://doi.org/10.1016/j.soildyn.2005.12.003.
Ghosh, B., and G. Madabhushi. 2002. “An efficient tool for measuring shear wave velocity in the centrifuge.” In Proc., Int. Conf. on Phys. Modelling in Geotechnics, edited by R. Phillips, P. J. Guo, and R. Popescu, 119–124. Rotterdam, Netherlands: A.A. Balkema.
Hall, J. R., Jr. 1967. “Coupled rocking and sliding oscillations of rigid circular footings.” In Proc., Int. Symp. on Wave Propagation and Dynamic Properties of Earth Materials, 139–148. Reston, VA: ASCE.
Hardin, B. O., and W. L. Black. 1968. “Vibration modulus of normally consolidated clay.” J. Soil Mech. Found. Div. 94 (2): 353–369. https://doi.org/10.1061/JSFEAQ.0001100.
Hardin, B. O., and W. L. Black. 1969. “Closure to vibration modulus of normally consolidated clays.” J. Soils Mech. Found. Div. 95 (6): 1531–1537. https://doi.org/10.1061/JSFEAQ.0001364.
Hardin, B. O., and V. P. Drnevich. 1972. “Shear modulus and damping in soils: Measurement and parameter effects.” J. Soil Mech. Found. Div. 98 (6): 603–624. https://doi.org/10.1061/JSFEAQ.0001756.
Hatzikonstantinou, E., J. L. Tassoulas, G. Gazetas, P. Kotsanopoulos, and M. Fotopoulou. 1989. “Rocking stiffness of arbitrarily shaped embedded foundations.” J. Geotech. Eng. 115 (4): 457–472. https://doi.org/10.1061/(ASCE)0733-9410(1989)115:4(457).
Heron, C. M. 2013. “The dynamic soil structure interaction of shallow foundation on dry sand beds.” Ph.D. thesis, Dept. of Engineering, Univ. of Cambridge.
Hoque, E., and F. Tatsuoka. 2000. “Kinematic elasticity of granular material.” In Proc., ISRM Int. Symp. Lisbon, Portugal: International Society for Rock Mechanics and Rock Engineering.
Jiang, X., and Z. Yan. 1998. “Earthquake response analysis of building-foundation-building interaction system.” J. Vib. Eng. 11 (1): 31–37.
Kirtas, E., and K. Pitilakis. 2009. “Subsoil interventions effect on structural seismic response. Part II: Parametric investigation.” J. Earthquake Eng. 13 (3): 328–344.
Kirtas, E., E. Rovithis, and K. Pitilakis. 2009. “Subsoil interventions effect on structural seismic response. Part I: Validation of numerical simulations.” J. Earthquake Eng. 13 (2): 155–169.
Kottke, A. R., X. Wang, and E. M. Rathje. 2019. Technical manual for Strata. Austin, TX: Geotechnical Engineering Center, University of Texas, Austin.
Madabhushi, G. 2015. Centrifuge modelling for civil engineers. Boca Raton, FL: Taylor & Francis.
Madabhushi, G., S. K. Haigh, N. E. Houghton, and E. Gould. 2012. “Development of a servo-hydraulic earthquake actuator for the Cambridge Turner beam centrifuge.” Int. J. Phys. Modell. Geotech. 12 (2): 77–88. https://doi.org/10.1680/ijpmg.11.00013.
Madabhushi, G., N. E. Houghton, and S. Haigh. 2006. “A new automatic sand pourer for model preparation at University of Cambridge.” In Proc., 6th Int. Conf. Physical Modelling in Geotechnics, 217–222. Boca Raton, FL: CRC Press.
Mahdavisefat, E., H. Salehzadeh, and A. A. Heshmati. 2018. “Full-scale experimental study on screening effectiveness of SRM-filled trench barriers.” Géotechnique 68 (10): 869–882. https://doi.org/10.1680/jgeot.17.P.007.
Martelli, A. 2009. “Development and application of innovative anti-seismic systems for the seismic protection of cultural heritage.” In Vol. 1 of Proc., Int. Conf. on “Protection of historical buildings by reversible mixed technologies, Prohitech09, 43–52. Boca Raton, FL: CRC Press.
Nappa, V., E. Bilotta, A. Flora, and G. Madabhushi. 2016. “Centrifuge modelling of the seismic performance of soft buried barriers.” Bull. Earthquake Eng. 14 (10): 2881–2901. https://doi.org/10.1007/s10518-016-9912-9.
Negro, P., R. Paolucci, S. Pedretti, and E. Faccioli. 2000. “Large scale soil-structure interaction experiments on sand under cyclic loading.” In Proc., 12th World Conf. on Earthquake Engineering, 1–8. Upper Hutt, New Zealand: New Zealand Society for Earthquake Engineering.
NIST (National Institute of Standards and Technology). 2012. Soil-structure interaction for building structures. Gaithersburg, MD: US Department of Commerce.
Pais, A., and E. Kausel. 1988. “Approximate formulas for dynamic stiffnesses of rigid foundations.” Soil Dyn. Earthquake Eng. 7 (4): 213–227. https://doi.org/10.1016/S0267-7261(88)80005-8.
Paolucci, R., R. Figini, L. Petrini, and M. Vecchiotti. 2011. “Accounting for non-linear dynamic soil-structure-interaction in the displacement-based seismic design.” In Proc., 5th Int. Conf. on Earthquake Geotechnical Engineering. London: International Society for Soil Mechanics and Geotechnical Engineering.
Pender, M. 2010. “Integrated earthquake resistant design of structure-foundation systems.” In Proc., 5th Int. Conf. on Recent Advances in Geotechnical and Earthquake Engineering and Soil Dynamics. Rolla, MO: Missouri University of Science and Technology.
Pitilakis, D., A. Anastasiadis, A. Vratsikidis, A. Kapouniaris, M. R. Massimino, G. Abate, and S. Corsico. 2021. “Large-scale field testing of geotechnical seismic isolation of structures using gravel-rubber mixtures.” Earthquake Eng. Struct. Dyn. 50 (10): 2712–2731. https://doi.org/10.1002/eqe.3468.
Pitilakis, K., S. Karapetrou, and K. Tsagdi. 2015. “Numerical investigation of the seismic response of RC buildings on soil replaced with rubber–sand mixtures.” Soil Dyn. Earthquake Eng. 79 (Dec): 237–252. https://doi.org/10.1016/j.soildyn.2015.09.018.
Robertson, P., and R. Campanella. 1983. “Interpretation of cone penetration tests. Part I: Sand.” Can. Geotech. J. 20 (4): 718–733. https://doi.org/10.1139/t83-078.
Sakellariadis, L., I. Anastasopoulos, and G. Gazetas. 2020. “Fukae bridge collapse (Kobe 1995) revisited: New insights.” Soils Found. 60 (6): 1450–1467. https://doi.org/10.1016/j.sandf.2020.09.005.
Schneider, J. A., and B. M. Lehane. 2006. “Effects of width for square centrifuge displacement piles in sand.” In Proc., 6th Int. Conf. Physical Modelling in Geotechnics, 867–873. Boca Raton, FL: CRC Press.
Shimamura, A. 2012. “Study on earthquake response reduction by improved composite geomaterial using rubber chips and fibrous materials.” Ph.D. thesis, Dept. of Civil Engineering, Osaka Univ.
Skempton, A. W., and D. H. MacDonald. 1956. “The allowable settlements of buildings.” Proc. Inst. Civ. Eng. 5 (6): 727–768. https://doi.org/10.1680/ipeds.1956.12202.
Steedman, R., and G. Madabhushi. 1991. “Wave propagation in sand medium.” In Proc., 4th Int. Conf. on Seismic Zonation. Oakland, CA: Earthquake Engineering Research Institute.
Trifunac, M. D., and A. G. Brady. 1975. “A study of the duration of strong earthquake ground motion.” Bull. Seismol. Soc. Am. 65 (3): 581–626.
Tsang, H., and K. Pitilakis. 2019. “Mechanism of geotechnical seismic isolation system: Analytical modeling.” Soil Dyn. Earthquake Eng. 122 (Jul): 171–184. https://doi.org/10.1016/j.soildyn.2019.03.037.
Tsang, H. H. 2009. “Geotechnical seismic isolation.” In Earthquake engineering: New research, 55–87. New York: Nova Science Publishers.
Veletsos, A. S., and J. W. Meek. 1974. “Dynamic behavior of building-foundation systems.” Earthquake Eng. Struct. Dyn. 3 (2): 121–138. https://doi.org/10.1002/eqe.4290030203.
Veletsos, A. S., and Y. T. Wei. 1971. “Lateral and rocking vibrations of footings.” J. Soil Mech. Found. Div. 97 (9): 1227–1248. https://doi.org/10.1061/JSFEAQ.0001661.
Whitman, R. V., and F. E. Richart Jr. 1967. “Design procedures for dynamically loaded foundations.” J. Eng. Mech. Div. 93 (6): 169–193.
Xiong, W., and Y. Li. 2013. “Seismic isolation using granulated tire–soil mixtures for less-developed regions: Experimental validation.” Earthquake Eng. Struct. Dyn. 42 (14): 2187–2193.
Yegian, M. K., and M. Catan. 2004. “Soil isolation for seismic protection using a smooth synthetic liner.” J. Geotech. Geoenviron. Eng. 130 (11): 1131–1139. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:11(1131).
Yegian, M. K., and U. Kadakal. 2004. “Foundation isolation for seismic protection using a smooth synthetic liner.” J. Geotech. Geoenviron. Eng. 130 (11): 1121–1130. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:11(1121).
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Mar 21, 2021
Accepted: Oct 29, 2021
Published online: Dec 8, 2021
Published in print: Feb 1, 2022
Discussion open until: May 8, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Fausto Somma, Alessandro Flora, SAP-sand mixtures as a geotechnical seismic isolation technology: from the dynamic characterization to a simple analytical design approach, Bulletin of Earthquake Engineering, 10.1007/s10518-023-01660-8, (2023).
- Fausto Somma, Gianpiero Lignola, Giancarlo Ramaglia, Luca de Sanctis, Maria Iovino, Sadik Oztoprak, Alessandro Flora, An interdisciplinary investigation of the seismic performance of a historic tower in Istanbul during the 1999 Kocaeli earthquake, Bulletin of Earthquake Engineering, 10.1007/s10518-023-01638-6, (2023).
- Hing-Ho Tsang, Analytical design models for geotechnical seismic isolation systems, Bulletin of Earthquake Engineering, 10.1007/s10518-022-01469-x, (2022).