Assessment of Several Nominal Resistance Interpretation Criteria for Drilled Foundations
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 148, Issue 2
Abstract
Agreeing on the nominal resistance (aka. capacity) derived from any load-settlement curve requires the use of an interpretation criterion. Few of the currently available criteria have been originally designed for drilled foundations despite the increasing use of such piles for supporting infrastructure projects. The performance of 16 interpretation criteria used in current geotechnical practice was assessed using a database of 194 load tests conducted on drilled shafts. Their performance was evaluated in terms of: (1) applicability; (2) correlation among each other; and (3) the effect of drilled shaft diameter, length, and soil type. Eight of the 16 methods could not be reliably used. Capacities interpreted from the remaining eight were consistent but resulted in excessive settlement in a few cases. Performance was also evaluated in terms of serviceability. A new criterion is proposed, where the nominal resistance is defined as the load corresponding to the smallest of (1) a settlement equal to the elastic compression of a free-standing column plus 0.75 in. (20 mm); (2) the load at plunging or strain-softening; or (3) settlement corresponding to 5% of the pile diameter, unless modified by the structural engineer of record. The proposed method showed good correlation with several established criteria while including a built-in serviceability safeguard against excessive settlement.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
The data employed in this study was publicly released by the Federal Highway Administration as part of the Deep Foundation Load Test Database (DFLTD v2), Publication No. FHWA-HRT-17-034.
References
AASHTO. 2014. AASHTO LRFD bridge design specifications, US customary units, 7’th edition, with 2015 interim revisions. Washington, DC: AASHTO.
Abu-Farsakh, M., and X. Yu. 2010. “Interpretation criteria to evaluate resistance factors for axial load capacity of drilled shafts.” J. Transp. Res. Rec. 2202 (1): 20–31. https://doi.org/10.3141/2202-03.
ASTM. 2013. Standard test methods for deep foundations under static axial compressive load. ASTM D1143/D1143M-07(2013)e1. West Conshohocken, PA: ASTM.
Briaud, J. L., and L. M. Tucker. 1988. “Measured and predicted axial response of 98 piles.” J. Geotech. Eng. 114 (9): 984–1001. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:9(984).
Camp, W. M., P. W. Mayne, and D. A. Brown. 2002. “Drilled shaft axial design values: Predicted versus measured response in a calcareous clay.” In Deep foundations 2002: An international perspective on theory, design, construction, and performance, 1518–1532. Reston, VA: ASCE.
Chellis, R. D. 1961. Pile foundations. New York: McGraw Hill Book Company.
Davisson, M. T. 1972. “High capacity piles.” In Proc., Lecture Series on Innovations in Foundation Construction, 81–112. Reston, VA: ASCE.
DeBeer, E. E. 1967. “Proefondervindlijke bijdrage tot de studie van het grensdraag vermogen van zand onder funderingen op staal.” [In Dutch.] Tijdshift der Openbar Verken van Belgie 6.
Dennis, N. D., and R. E. Olson. 1983a. “Axial capacity of steel pipe piles in clay.” In Proc., Conf. on Geotechnical Practice on Offshore Engineering, 370–388. Reston, VA: ASCE.
Dennis, N. D., and R. E. Olson. 1983b. “Axial capacity of steel pipe piles in sand.” In Proc., Conf. on Geotechnical Practice on Offshore Engineering, 389–402. Reston, VA: ASCE.
Fellenius, H. B. 2020. Basics of foundation design (The red book). Electronic ed. Sidney, BC: Fellenius.
Hirany, A., and F. H. Kulhawy. 1988. Conduct and interpretation of load tests on drilled shaft foundations: Volume 1, detailed guidelines (No. EPRI-EL-5915-Vol. 1). Palo Alto, CA: Electric Power Research Institution, Cornell Univ., Geotechnical Engineering Group.
Hirany, A., and F. H. Kulhawy. 1989. “Interpretation of load tests on drilled shafts—Part 1: Axial compression.” In Foundation engineering: Current principles and practices, 1132–1149. Reston, VA: ASCE.
Hirany, A., and F. H. Kulhawy. 2002. “On the interpretation of drilled foundation load test results.” In Deep foundations 2002: An international perspective on theory, design, construction, and performance, 1018–1028. Reston, VA: ASCE.
Iskander, M. 2010. Behavior of pipe piles in sand: Plugging and pore-water pressure generation during installation and loading. Springer series in geomechanics and geoengineering. Berlin: Springer.
Kalavar, S., and C. Ealy. 2000. “FHWA deep foundation load test database.” In New technological and design developments in deep foundations, 192–206. Reston, VA: ASCE.
Kodsy, A., N. Machairas, and M. Iskander. 2021. “Assessment of several interpreted pile capacity criteria for large-diameter open-ended piles.” Geotech. Test. J. 44 (5): 1217–1243. https://doi.org/10.1520/GTJ20200074.
Machairas, N., G. A. Highley, and M. G. Iskander. 2018. “Evaluation of FHWA pile design method against the FHWA deep foundation load test database Version 2.0.” Transp. Res. Rec. 2672 (52): 268–277. https://doi.org/10.1177/0361198118773196.
Ng, C. W., T. L. Yau, J. H. Li, and W. H. Tang. 2001. “New failure load criterion for large diameter bored piles in weathered geomaterials.” J. Geotech. Geoenviron. Eng. 127 (6): 488–498. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:6(488).
Olson, R., and M. Iskander. 2014. “Axial load capacity of pipe piles in sands.” In From soil behavior fundamentals to innovations in geotechnical engineering, 209–220. Reston, VA: ASCE.
O’Neil, M. W., and L. C. Reese. 1999. Drilled shafts: Construction procedures and design methods. Washington, DC: US DOT, Federal Highway Administration.
Price, R., K. M. Rollins, and E. Keane. 1992. “Comparison of measured and computed drilled shaft capacities based on Utah load tests.” Transp. Res. Rec. 1336: 57–64.
Rollins, K. M., R. J. Clayton, R. C. Mikesell, and B. C. Blaise. 2005. “Drilled shaft side friction in gravelly soils.” J. Geotech. Geoenviron. Eng. 131 (8): 987–1003. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:8(987).
Vesic, A. 1963. “Bearing capacity of deep foundations in sand.” Highway Res. Rec. 39: 112–153.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Sep 11, 2020
Accepted: Oct 12, 2021
Published online: Nov 30, 2021
Published in print: Feb 1, 2022
Discussion open until: Apr 30, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Antonio Kodsy, Baturalp Öztürk, Youssef Bazi, Magued G. Iskander, Assessment of Several Interpretation Criteria for Tensile Axial Load Tests on Deep Foundations, Transportation Research Record: Journal of the Transportation Research Board, 10.1177/03611981221149435, (036119812211494), (2023).
- Antonio Kodsy, Baturalp Ozturk, Magued Iskander, Forecasting of pile plugging using machine learning, Acta Geotechnica, 10.1007/s11440-023-01797-5, (2023).
- Antonio Kodsy, Magued Iskander, Insights into Plugging of Pipe Piles Based on Pile Dimensions, Applied Sciences, 10.3390/app12052711, 12, 5, (2711), (2022).
- Antonio Kodsy, Magued G. Iskander, Akash Sampurnanand Pandey, Universal Criterion for Interpreting Capacity from Load Tests on Piles, Transportation Research Record: Journal of the Transportation Research Board, 10.1177/03611981221084686, 2676, 8, (530-541), (2022).