SHANSEP-Based Interpretation of Overconsolidation Effect on Monotonic Shearing Resistance of Contractive Nonplastic Soils
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 147, Issue 12
Abstract
The effect of overconsolidation on the monotonic shearing resistance of three nonplastic soils (a clean sand, a clean sand and fine tailings mixture, and a fine tailings) was examined using laboratory -consolidated constant volume direct simple shear (DSS) tests performed on contractive specimens. Two different overconsolidation methods were used. Isotopically consolidated undrained triaxial compression (CIU-TC) tests from the literature also are presented. The stress history and normalized soil engineering properties (SHANSEP) equation was used to interpret the relationship between strength ratios and overconsolidation ratio (OCR). The SHANSEP equation appears to capture the increases in strength ratios, at both the peak and the critical states, with OCR. However, only the increase in undrained critical state shear strength ratio, , with OCR can be derived based on critical state soil mechanics concepts using the swelling index, , compression index, , and slope of the critical state line, . In addition, theoretical derivation showed that the strength ratio increase can be affected by the method of overconsolidation, especially when is small. Overall, the SHANSEP equation parameter obtained from the constant volume DSS and CIU-TC tests was in good agreement with theoretical values.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
References
Airey, D. W., M. Budhu, and D. M. Wood. 1985. “Some aspect of the behaviour of soils in simple shear.” In Developments in soil mechanics and foundation engineering volume 2: Stress-strain modelling of soils, edited by P. K. Banerjee and R. Butterfield, 185–213. London: CRC Press.
Airey, D. W., and D. M. Wood. 1987. “An evaluation of direct simple shear tests on clay.” Géotechnique 37 (1): 25–35. https://doi.org/10.1680/geot.1987.37.1.25.
Amer, M. I., W. D. Kovacs, and M. S. Aggour. 1987. “Cyclic simple shear size effects.” J. Geotech. Eng. 113 (7): 693–707. https://doi.org/10.1061/(ASCE)0733-9410(1987)113:7(693).
ASTM. 2014. Standard test methods for specific gravity of soil solids by water pycnometer. ASTM D854-14. West Conshohocken, PA: ASTM.
ASTM. 2017a. Standard test method for consolidated undrained direct simple shear testing of fine grain soils. ASTM D6528-17. West Conshohocken, PA: ASTM.
ASTM. 2017b. Standard test method for particle-size distribution (gradation) of fine-grained soils using the sedimentation (hydrometer) analysis. ASTM D7928-17. West Conshohocken, PA: ASTM.
ASTM. 2017c. Standard test methods for particle-size distribution (gradation) of soils using sieve analysis. ASTM D6913/D6913M-17. West Conshohocken, PA: ASTM.
Azzouz, A. S., A. M. Malek, and M. M. Baligh. 1989. “Cyclic behavior of clays in undrained simple shear.” J. Geotech. Eng. 115 (5): 637–657. https://doi.org/10.1061/(ASCE)0733-9410(1989)115:5(637).
Berre, T. 1982. “Triaxial testing at the Norwegian Geotechnical Institute.” Geotech. Test. J. 5 (1–2): 3–17.
Bhaumik, L., C. J. Rutherford, A. Cerna-Diaz, S. M. Olson, O. A. Numanoglu, Y. M. Hashash, and T. Weaver. 2017. “Volumetric strain in non-plastic silty sand subject to multidirectional cyclic loading.” In Proc., Geotechnical Frontiers 2017, 150–159. Reston, VA: ASCE. https://doi.org/10.1061/9780784480489.016.
Bishop, A. W. 1967. “Progressive failure-with special reference to the mechanism causing it.” In Vol. 2 of Proc., Geotechnical Conf., 142–150. Oslo, Norway: Norwegian Geotechnical Institute.
Bishop, A. W. 1971. “Shear strength parameters for undisturbed and remoulded soil specimens.” In Proc., Roscoe Memorial Symp., 3–58. Cambridge, UK: Cambridge Univ.
Bjerrum, L., and A. Landva. 1966. “Direct simple-shear tests on a Norwegian quick clay.” Géotechnique 16 (1): 1–20. https://doi.org/10.1680/geot.1966.16.1.1.
Burland, J. B., and M. C. Burbidge. 1985. “Settlement of foundations on sand and gravel.” Proc. Inst. Civ. Eng. 78 (6): 1325–1381. https://doi.org/10.1680/iicep.1985.1058.
Campanella, R., and B. Lim. 1981. “Liquefaction characteristics of undisturbed soils.” In Proc., Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, 227–230. St. Louis: Univ. of Missouri–Rolla.
Casagrande, A. 1936. “Characteristics of cohesionless soils affecting the stability of slopes and earth fills.” J. Boston Soc. Civ. Eng. 23 (1): 13–32.
Casto, G. 1975. “Liquefaction and cyclic mobility of saturated sands.” J. Geotech Eng. Div. 101 (6): 551–569. https://doi.org/10.1061/AJGEB6.0000173.
Chen, J. 2021. “An investigation of liquefied shear strength using novel centrifuge tests, direct simple shear tests, and field case histories.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana–Champaign.
DeGroot, D. J., J. T. Germaine, and C. C. Ladd. 1994. “Effect of nonuniform stresses on measured DSS stress-strain behavior.” J. Geotech. Eng. 120 (5): 892–912. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:5(892).
Donahue, J. L. 2007. “The liquefaction susceptibility, resistance, and response of silty and clayey soils.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of California, Berkeley.
Dyvik, R., T. Berre, S. Lacasse, and B. Raadim. 1987. “Comparison of truly undrained and constant volume direct simple shear tests.” Géotechnique 37 (1): 3–10. https://doi.org/10.1680/geot.1987.37.1.3.
Finn, W. D. 1981. “Liquefaction potential: Developments since 1976.” In Proc., Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, 655–681. St. Louis: Univ. of Missouri–Rolla.
Finn, W. D. L., D. J. Pickering, and P. L. Bransby. 1971. “Sand liquefaction in triaxial and simple shear tests.” J. Soil Mech. Found. Div. 97 (4): 639–659. https://doi.org/10.1061/JSFEAQ.0001579.
Fleming, L. N., and J. M. Duncan. 1990. “Stress-deformation characteristics of Alaskan silt.” J. Geotech. Eng. 116 (3): 377–393. https://doi.org/10.1061/(ASCE)0733-9410(1990)116:3(377).
Franke, E., M. Kiekbusch, and B. Schuppener. 1979. “A new direct simple shear device.” Geotech. Test. J. 2 (4): 190–199. https://doi.org/10.1520/GTJ10457J.
Ishihara, K., M. Sodekawa, and Y. Tanaka. 1978. “Effects of overconsolidation on liquefaction characteristics of sands containing fines.” In Proc., Dynamic Geotechnical Testing, 246–264. West Conshohocken, PA: ASTM.
Ishihara, K., and H. Takatsu. 1979. “Effects of overconsolidation and , conditions on the liquefaction characteristics of sands.” Soils Found. 19 (4): 59–68. https://doi.org/10.3208/sandf1972.19.4_59.
Ishihara, K., F. Tatsuoka, and S. Yasuda. 1975. “Undrained deformation and liquefaction of sand under cyclic stresses.” Soils Found. 15 (1): 29–44. https://doi.org/10.3208/sandf1972.15.29.
Jefferies, M., and K. Been. 2015. Soil liquefaction: A critical state approach. 2nd ed. Boca Raton, FL: CRC Press.
Ladd, C. C. 1991. “Stability evaluation during staged construction.” J. Geotech. Eng. 117 (4): 540–615. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:4(540).
Ladd, C. C., and R. Foott. 1974. “New design procedure for stability of soft clays.” J. Geotech. Eng. Div. 100 (7): 763–786. https://doi.org/10.1061/AJGEB6.0000066.
Ladd, C. C., R. Foott, K. Ishihara, F. Schlosser, and H. G. Poulos. 1977. “Stress deformation and strength characteristics.” In Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, 421–494. Tokyo: Japanese Society of Soil Mechanics and Foundation Engineering.
Lade, P. V., C. D. Liggio, and J. A. Yamamuro. 1998. “Effects of non-plastic fines on minimum and maximum void ratios of sand.” Geotech. Test. J. 21 (4): 336. https://doi.org/10.1520/GTJ11373J.
Manmatharajan, V. 2011. “Initial stress state and stress history effects on liquefaction susceptibility of sands.” Master’s thesis, Dept. of Civil and Environmental Engineering, Carleton Univ.
Mesri, G., and B. Vardhanabhuti. 2009. “Compression of granular materials.” Can. Geotech. J. 46 (4): 369–392. https://doi.org/10.1139/T08-123.
Mitchell, J. K., and K. Soga. 2005. Fundamentals of soil behavior. 3rd ed. New York: Wiley.
Price, A. B. 2018. “Cyclic strength and cone penetration resistance for mixtures of silica silt and kaolin.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of California, Davis.
Puri, V. K. 1984. “Liquefaction behavior and dynamic properties of loessial (silty) soils.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Missouri–Rolla.
Qian, J., S. Li, J. Zhang, J. Jiang, and Q. Wang. 2019. “Effects of OCR on monotonic and cyclic behavior of reconstituted Shanghai silty clay.” Soil Dyn. Earthquake Eng. 118 (Mar): 111–119. https://doi.org/10.1016/j.soildyn.2018.12.010.
Roscoe, K. H. 1953. “An apparatus for the application of simple shear to soil samples.” In Proc., 3rd Int. Conf. on Soil Mechanics and Foundation Engineering, 186–191. Zürich, Switzerland: Organizing Committee, ICOSOMEF.
Roscoe, K. H., and J. B. Burland. 1968. “On the generalized stress-strain behavior of wet clay.” Accessed June 15, 2020. https://trid.trb.org/view/124868.
Sadrekarimi, A., and S. M. Olson. 2011. “Yield strength ratios, critical strength ratios, and brittleness of sandy soils from laboratory tests.” Can. Geotech. J. 48 (3): 493–510. https://doi.org/10.1139/T10-078.
Sandoval-Shannon, J. A. 1989. “Liquefaction and settlement characteristics of silt soils.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Missouri–Rolla.
Sasitharan, S., P. K. Robertson, D. C. Sego, and N. R. Morgenstern. 1994. “State boundary surface for very loose sand and its practical implications.” Can. Geotech. J. 31 (3): 321–334. https://doi.org/10.1139/t94-040.
Saye, S. R., B. P. Kumm, and A. J. Lutenegger. 2021. “Estimating the OCR in structured and unstructured cohesive soil with field vane tests referencing soil index properties.” Can. Geotech. J. 58 (1): 125–141. https://doi.org/10.1139/cgj-2019-0414.
Saye, S. R., A. J. Lutenegger, J. Santos, and B. P. Kumm. 2013. “Assessing overconsolidation ratios in soil with piezocone: Referencing soil index properties.” J. Geotech. Geoenviron. Eng. 139 (7): 1075–1085. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000841.
Seed, H. B., and W. H. Peacock. 1971. “Test procedures for measuring soil liquefaction characteristics.” J. Soil Mech. Found. Div. 97 (8): 1099–1119. https://doi.org/10.1061/JSFEAQ.0001649.
Shahsavari Goughari, M. 2012. “Effect of initial shear stress direction and stress history on the undrained behaviour of sands under triaxial loading.” Master’s thesis, Dept. of Civil and Environmental Engineering, Carleton Univ. (Canada).
Stamatopoulos, C., A. Stamatopoulos, and P. Kotzias. 1995. “Effect of prestress on the liquefaction potential of silty sand.” In Proc., 7th Int. Conf. on Soil Dynamics and Earthquake Engineering (SDEE 95) Hellenic Society of Soil Mechanics and Foundation Engineering, Greece, 181–188. Southampton, UK: Computational Mechanics Publications.
Stuedlein, A. W., S. R. Saye, and B. P. Kumm. 2020. “SHANSEP-based side resistance of driven pipe piles in plastic soils: Revision and LRFD calibration.” J. Geotech. Geoenviron. Eng. 146 (8): 06020010. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002319.
Terzaghi, K., R. B. Peck, and G. Mesri. 1996. Soil mechanics in engineering practice. 3rd ed. New York: Wiley.
Thornton, C., and L. Zhang. 2006. “A numerical examination of shear banding and simple shear non-coaxial flow rules.” Philos. Mag. 86 (21–22): 3425–3452. https://doi.org/10.1080/14786430500197868.
Wang, S., and R. Luna. 2012. “Monotonic behavior of Mississippi river valley silt in triaxial compression.” J. Geotech. Geoenviron. Eng. 138 (4): 516–525. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000603.
Wang, S., R. Luna, and S. Onyejekwe. 2016. “Effect of initial consolidation condition on postcyclic undrained monotonic shear behavior of Mississippi River Valley silt.” J. Geotech. Geoenviron. Eng. 142 (2): 04015075. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001401.
Wijewickreme, D., A. Dabeet, and P. Byrne. 2013. “Some observations on the state of stress in the direct simple shear test using 3D discrete element analysis.” Geotech. Test. J. 36 (2): 20120066. https://doi.org/10.1520/GTJ20120066.
Wijewickreme, D., A. Soysa, and P. Verma. 2019. “Response of natural fine-grained soils for seismic design practice: A collection of research findings from British Columbia, Canada.” Soil Dyn. Earthquake Eng. 124 (Sep): 280–296. https://doi.org/10.1016/j.soildyn.2018.04.053.
Yamamuro, J. A., and P. V. Lade. 1998. “Steady-state concepts and static liquefaction of silty sands.” J. Geotech. Geoenviron. Eng. 124 (9): 868–877. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:9(868).
Yasuhara, K., S. Murakami, B.-W. Song, S. Yokokawa, and A. F. L. Hyde. 2003. “Postcyclic degradation of strength and stiffness for low plasticity silt.” J. Geotech. Geoenviron. Eng. 129 (8): 756–769. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:8(756).
Youd, T. L., and D. M. Perkins. 1978. “Mapping liquefaction-induced ground failure potential.” J. Geotech. Eng. Div. 104 (4): 433–446. https://doi.org/10.1061/AJGEB6.0000612.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Dec 8, 2020
Accepted: Jul 22, 2021
Published online: Sep 29, 2021
Published in print: Dec 1, 2021
Discussion open until: Feb 28, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Jiarui Chen, Scott M. Olson, Effect of Overconsolidation on Cyclic Resistance of Soils, Journal of Geotechnical and Geoenvironmental Engineering, 10.1061/(ASCE)GT.1943-5606.0002905, 148, 11, (2022).
- Gertraud Medicus, Katherine A. Kwa, Benjamin Cerfontaine, A consistent calibration process for the Matsuoka–Nakai friction angle under direct simple shear conditions for clay hypoplasticity, Computers and Geotechnics, 10.1016/j.compgeo.2022.104888, 150, (104888), (2022).