Centrifuge Tests on Rock-Socketed Piles: Effect of Socket Roughness on Shaft Resistance
This article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYThis article has a reply.
VIEW THE REPLYPublication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 147, Issue 11
Abstract
Preliminary estimations of shaft resistance of rock-socketed piles are usually conducted using empirical formulations that relate to the uniaxial compressive strength () of the weaker material involved (intact rock or pile). However, there are other factors, such as the degree of socket roughness, that could affect the shaft resistance of rock-socketed piles. In this paper, results from geotechnical centrifuge tests are presented to demonstrate the effect of socket roughness on the pile shaft resistance. Aluminum model piles with different degrees of shaft roughness were fabricated and embedded within an artificial rock mixture composed of sand, cement, bentonite, and water. Pile loading tests were conducted within the centrifuge and axial forces along the model piles were measured using fiber Bragg grating (FBG) sensing technology. Results are used to demonstrate that centrifuge testing provides a suitable experimental method to study and quantify the effect of socket roughness on the shaft shearing mechanism of rock-socketed piles. Finally, the centrifuge test measurements are compared with several formulations published in the literature, suggesting that centrifuge measurements tend to agree with the overall trend, despite the variability of predictions obtained with different formulations.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request (centrifuge test results).
Acknowledgments
This research was funded, in part, by the Spanish Ministries of Economy, Industry and Competitiveness and Science and Innovation under Projects BIA 2015-69152-R and PID2019-108060RB-I00. The first author was the recipient during 2019 of one Fellowship for PhD research provided by the José Entrecanales Ibarra Foundation. The support of both institutions is gratefully acknowledged.
References
AASHTO. 2008. LRFD bridge design specifications. Washington, DC: AASHTO.
Álvarez-Botero, G., F. E. Barón, C. C. Canom, O. Sosa, and M. Varón. 2017. “Optical sensing using fiber Bragg gratings: Fundamentals and applications.” IEEE Instrum. Meas. Mag. 20 (2): 33–38. https://doi.org/10.1109/MIM.2017.7919131.
Asem, P. 2020. “The effect of expansive concrete on the side resistance of sockets in weak rock.” Soils Found. 60 (1): 274–282. https://doi.org/10.1016/j.sandf.2020.02.002.
Asem, P., and P. Gardoni. 2019. “A load-transfer function for the side resistance of drilled shafts in soft rock.” Soils Found. 59 (5): 1241–1259. https://doi.org/10.1016/j.sandf.2019.04.006.
CGS (Canadian Geotechnical Society). 2006. Canadian foundation engineering manual. 4th ed. Calgary, Canada: CGS.
Dai, G., R. Salgado, W. Gong, and M. Zhu. 2017. “The effect of sidewall roughness on the shaft resistance of rock-socketed piles.” Acta Geotech. 12 (2): 429–440. https://doi.org/10.1007/s11440-016-0470-8.
Dykeman, P., and A. L. Valsangkar. 1996. “Model studies of socketed caisson in soft rock.” Can. Geotech. J. 33 (5): 747–759. https://doi.org/10.1139/t96-100-321.
Gu, X. F., J. P. Seidel, and C. M. Haberfield. 2003. “Direct shear test of sandstone-concrete joints.” Int. J. Geomech. 3 (1): 21–33. https://doi.org/10.1061/(ASCE)1532-3641(2003)3:1(21).
Gutiérrez-Ch, J. G. 2020. “Análisis del efecto de la rugosidad en el contacto roca-pilote sobre la resistencia por fuste de pilotes.” [In Spanish.] Ph.D. thesis, Ingeniería y Morfología del Terreno, Universidad Politécnica de Madrid.
Gutiérrez-Ch, J. G., S. Melentijevic, S. Senent, and R. Jimenez. 2019. “DEM models to predict shaft resistance of rock-socketed piles considering socket roughness.” In Proc., 53rd US Rock Mechanics/Geomechanics Symp., 19–57. New York: American Rock Mechanics Association.
Gutiérrez-Ch, J. G., S. Melentijevic, S. Senent, and R. Jimenez. 2020a. “Distinct element method simulations of rock-socketed piles: Estimation of shaft resistance considering socket roughness.” J. Geotech. Geoenviron. Eng. 146 (12): 04020133. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002394.
Gutiérrez-Ch, J. G., S. Senent, S. Melentijevic, and R. Jimenez. 2018. “Distinct element method simulations of rock-concrete interfaces under different boundary conditions.” Eng. Geol. 240 (Jun): 123–139. https://doi.org/10.1016/j.enggeo.2018.04.017.
Gutiérrez-Ch, J. G., S. Senent, S. Melentijevic, and R. Jimenez. 2021. “A DEM-based factor to design rock-socketed piles considering socket roughness.” Rock Mech. Rock Eng. 54 (Jan): 3409–3421. https://doi.org/10.1007/s00603-020-02347-1.
Gutiérrez-Ch, J. G., G. Song, C. Heron, A. Marschall, and R. Jimenez. 2020b. “Centrifuge modelling of shaft resistance of a rock-socketed pile.” In Proc., 4th European Conf. on Physical Modelling in Geotechnics-ECPMG. Luleå, Sweden: Luleå Univ. of Technology.
Haberfield, C. M., and A. L. E. Lochaden. 2019. “Analysis and design of axially loaded piles in rock.” J. Rock Mech. Geotech. Eng. 11 (3): 535–548. https://doi.org/10.1016/j.jrmge.2018.10.001.
Hassan, K. M., and M. W. O’Neill. 1997. “Side load-transfer mechanisms in drilled shafts in soft argillaceous rock.” J. Geotech. Geoenviron. Eng. 123 (2): 145–152. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:2(145).
Hassan, K. M., M. W. O’Neill, S. A. Sheikh, and C. D. Ealy. 1997. “Design method for drilled shafts in soft argillaceous rock.” J. Geotech. Geoenviron. Eng. 123 (3): 272–280. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:3(272).
Horvath, R. G., and T. C. Kenney. 1979. “Shaft resistance of rock-socketed drilled piers.” In Proc., Symp. on Deep Foundations, 182–214. New York: ASCE.
Horvath, R. G., T. C. Kenney, and P. Kozicki. 1983. “Methods for improving the performance of drilled piers in weak rock.” Can. Geotech. J. 20 (4): 758–772. https://doi.org/10.1139/t83-081.
Johnston, I. W., T. S. K. Lam, and A. F. Williams. 1987. “Constant normal stiffness direct shear testing for socketed pile design in weak rock.” Géotechnique 37 (1): 83–89. https://doi.org/10.1680/geot.1987.37.1.83.
Kashyap, R. 2010. Fiber Bragg gratings. 2nd ed. Burlington, MA: Academic Press.
Kodikara, J. K., and I. W. Johnston. 1994. “Shear behaviour of irregular triangular rock-concrete joints.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 31 (4): 313–322. https://doi.org/10.1016/0148-9062(94)90900-8.
Kreuzer, M. 2006. “Strain measurement with fiber Bragg grating sensors.” Darmstadt, Germany: Hottinger Baldwin Messtechnik.
Leung, C. F., and H.-Y. Ko. 1993. “Centrifuge model study of piles socketed in soft rock.” Jpn. Soc. Soil Mech. Found. Eng. 33 (33): 88–91. https://doi.org/10.3208/sandf1972.33.3_80.
Nam, M. S., and C. Vipulanandan. 2008. “Roughness and unit side resistances of drilled shafts socketed in clay shale and limestone.” J. Geotech. Geoenviron. Eng. 134 (9): 1272–1279. https://doi.org/10.1061/(ASCE)1090-0241(2008)134:9(1272).
O’Neill, M. W., and L. C. Reese. 1999. Drilled shafts: Construction procedures and design methods. Washington, DC: Federal Highway Administration, US DOT.
O’Neill, M. W., F. C. Townsend, K. M. Hassan, A. Buller, and P. S. Chan. 1996. Load transfer for drilled shafts in intermediate geomaterials. Washington, DC: Federal Highway Administration, US DOT.
Pells, P. J. N., D. J. Douglas, B. Rodway, C. P. Thorne, and B. R. McMahon. 1978. “Design loadings for shales and sandstones in the Sydney region.” Aust. Geomech. J. G8: 31–39. https://doi.org/10.1016/0148-9062(79)91634-6.
Pells, P. J. N., R. K. Rowe, and R. M. Turner. 1980. “Experimental investigation into shear for socketed piles in sandstone.” In Vol. 1 of Proc., Int. Conf. on Structure Foundation on Rock, 291–302. Rotterdam, Netherlands: A.A. Balkema. https://doi.org/10.1016/0148-9062(81)90887-1.
Rezazadeh, S., and A. Eslami. 2017. “Empirical methods for determining shaft bearing capacity of semi-deep foundations socketed in rocks.” Int. J. Rock Mech. Geotech. Eng. 9 (6): 1140–1151. https://doi.org/10.1016/j.jrmge.2017.06.003.
Rowe, R. K., and H. H. Armitage. 1987. “A design method for drilled piers in soft rock.” Can. Geotech. J. 24 (1): 126–142. https://doi.org/10.1139/t87-011.
Salgado, R. 2008. The engineering of foundations. New York: McGraw-Hill.
Seidel, J. P., and B. Collingwood. 2001. “A new socket roughness factor for prediction of rock socket shaft resistance.” Can. Geotech. J. 38 (1): 138–153. https://doi.org/10.1139/t00-083.
Seidel, J. P., and C. M. Haberfield. 1995. “The axial capacity of pile sockets in rocks and hard soils.” Ground Eng. 28 (2): 33–38. https://doi.org/10.1016/0148-9062(95)93395-6.
Seol, H. I., and S. S. Jeong. 2007. “Shaft resistance characteristics of rock-socketed drilled shafts based on pile load tests.” J. Korean Geotech. Soc. 23 (9): 51–63.
Song, G. 2019. “The use of protective structures to reduce tunnelling induced damage to buildings.” Ph.D. thesis, Faculty of Engineering, Univ. of Nottingham.
Song, G., A. M. Marshall, and C. M. Heron. 2019. “Load redistribution of piles affected by tunnelling: Hybrid centrifuge tests using fibre Bragg grating.” In Proc., XVII European Conf. on Soil Mechanics and Geotechnical Engineering. Reykjavik, Iceland: Icelandic Geotechnical Society.
Taylor, R. N. 1995. Geotechnical centrifuge technology. London: Blackie Academic & Professional.
Whitaker, T., and R. W. Cooke. 1966. “An investigation of the shaft and base resistances of large bored piles in London Clay.” In Proc., Symp. of Large Bored Piles, 7–49. London: Institution of Civil Engineers.
Williams, A. F., I. W. Johnston, and I. B. Donald. 1980. “The design of socketed piles in weak rock.” In Vol. 1 of Proc., Int. Conf. on Structural Foundations on Rock, 327–347. Rotterdam, Netherlands: A.A. Balkema.
Xing, H., Z. Zhang, M. Meng, Y. Luo, and G. Ye. 2014. “Centrifuge tests of superlarge-diameter rock-socketed piles and their bearing characteristics.” J. Bridge Eng. 19 (6): 04014010. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000582.
Xu, J., A. Haque, W. Gong, R. P. Gamage, G. Dai, Q. Zhang, and F. Xu. 2020. “Experimental study on the bearing mechanisms of rock-socketed piles in soft rock based on micro X-ray CT analysis.” Rock Mech. Rock Eng. 53 (8): 3395–3416. https://doi.org/10.1007/s00603-020-02121-3.
Zhang, L. M., and E. Y. Wong. 2007. “Centrifuge modelling of large-diameter bored pile groups with defects.” J. Geotech. Geoenviron. Eng. 133 (9): 1091–1101. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:9(1091).
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: May 21, 2020
Accepted: Jul 7, 2021
Published online: Aug 31, 2021
Published in print: Nov 1, 2021
Discussion open until: Jan 31, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Arun Kumar Murali, Khoa M. Tran, Asadul Haque, Ha H. Bui, Experimental and Numerical Investigation of the Load-Bearing Mechanisms of Piles Socketed in Soft Rocks, Rock Mechanics and Rock Engineering, 10.1007/s00603-022-02954-0, 55, 9, (5555-5576), (2022).
- Adis Skejić, Dejan Gavrić, Mario Jurišić, Đani Rahimić, Experimental and Numerical Analysis of Axially Loaded Bored Piles Socketed in a Conglomerate Rock Mass, Rock Mechanics and Rock Engineering, 10.1007/s00603-022-02932-6, 55, 10, (6339-6365), (2022).