Group Effect of Pipe Jacking in Silty Sand
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 147, Issue 11
Abstract
Jacking force is one of the most important parameters in pipe jacking engineering, and also the key in pipe jacking design. A lot of research has been done on the prediction of jacking force of a single pipe. However, the research on jacking force of a row of steel pipes is relatively rare. A case of pipe jacking project is studied in this paper. In construction the test pipes were successfully jacked into the designed position, but the subsequent pipes were stuck because the jacking machine could not provide enough jacking force. Based on this phenomenon, the influence on the jacking force from the pipe spacing and the number of pipes have been jacked around the pipe being jacked is studied by field measurement and numerical simulation. The mechanism of the steel pipes stuck after the test pipes is analysed in detail. The results show that the jacking force decreases nonlinearly with the increase of the pipe spacing, and the influence range of pipe jacking is three times the pipe diameter; the jacking force increases with the increment of the number of pipes that have been jacked, but the increasing trend gradually slows down. Based on the above results, the pipe group effect of jacking force is proposed which is verified by the measured data. The results indicate that the amplification and superposition effect of the jacking force should be considered in the design stage to avoid pipes stuck in the jacking process.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
This study is supported by the National Key R&D Program (2017YFC0805403), (2019YFC1509704) and the National Natural Science Foundation of China (41877218), (42072308). These financial supports are gratefully acknowledged.
References
Barla, M., and M. Camusso. 2013. “A method to design microtunnelling installations in randomly cemented Torino alluvial soil.” Tunnelling Underground Space Technol. 33 (1): 73–81. https://doi.org/10.1016/j.tust.2012.09.002.
Barla, M., M. Camusso, and S. Aiassa. 2006. “Analysis of jacking forces during microtunnelling in limestone.” Tunnelling Underground Space Technol. 21 (6): 668–683. https://doi.org/10.1016/j.tust.2006.01.002.
Bergeson, W. 2014. “Review of long drive microtunneling technology for use on large scale projects.” Tunnelling Underground Space Technol. 39 (Jan): 66–72. https://doi.org/10.1016/j.tust.2013.02.001.
Chapman, D. N., C. D. F. Rogers, H. J. Burd, P. M. Norris, and G. W. E. Milligan. 2007. “Research needs for new construction using trenchless technologies.” Tunnelling Underground Space Technol. 22 (5–6): 491–502. https://doi.org/10.1016/j.tust.2007.05.003.
Cheng, W. C., J. C. Ni, J. S.-L. Shen, and H.-W. Huang. 2017. “Investigation into factors affecting jacking force: A case study.” Proc. Inst. Civ. Eng. Geotech. Eng. 170 (4): 322–334. https://doi.org/10.1680/jgeen.16.00117.
Choo, C. S., and D. E. L. Ong. 2015. “Evaluation of pipe-jacking forces based on direct shear testing of reconstituted tunneling rock spoils.” J. Geotech. Geoenviron. Eng. 141 (10): 04015044. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001348.
Coller, P. J., and D. G. Abbott. 1994. “Microtunneling techniques to form an in situ barrier around existing structures.” In High Level Radioactive Waste Management: Proc., 5th Annual Int. Conf., 386–394. Reston, VA: ASCE.
Cui, Q.-L., Y.-S. Xu, S.-L. Shen, Z.-Y. Yin, and S. Horpibulsuk. 2015. “Field performance of concrete pipes during jacking in cemented sandy silt.” Tunnelling Underground Space Technol. 49 (Jun): 336–344. https://doi.org/10.1016/j.tust.2015.05.005.
Hemerijckx, E. 1983. “Tubular trust jacking for underground roof construction on the Antwerp Metro.” In Tunnels & tunneling International. Sidcup, VA: Progressive Media Markets.
Ji, X., P. Ni, and M. Barla. 2019a. “Analysis of jacking forces during pipe jacking in granular materials using particle methods.” Underground Space 4 (4): 277–288. https://doi.org/10.1016/j.undsp.2019.03.002.
Ji, X., W. Zhao, P. Jia, L. Qiao, M. Barla, P. Ni, and L. Wang. 2017. “Pipe Jacking in sandy soil under a river in Shenyang, China.” Indian Geotech. J. 47 (3): 246–260. https://doi.org/10.1007/s40098-016-0195-5.
Ji, X. B., W. Zhao, P. P. Ni, B. Marco, J. Y. Han, and P. J. Jia. 2019b. “A method to estimate the jacking force for pipe jacking in sandy soils.” Tunnelling Underground Space Technol. 90 (Aug): 119–130. https://doi.org/10.1016/j.tust.2019.04.002.
JMTA (Japan Microtunnelling Association). 2000. Pipe-jacking application. Tokyo: JMTA.
Khazaei, S., W. Wu, H. Shimada, and K. Matsui. 2006. “Effect of lubrication strength on efficiency of slurry pipe jacking.” In Proc., Underground Construction and Ground Movement, GeoShanghai Int. Conf. Reston, VA: ASCE.
Li, P., S. J. Du, X. F. Ma, Z. Y. Yin, and S. L. Shen. 2014. “Centrifuge investigation into the effect of new shield tunnelling on an existing underlying large-diameter tunnel.” Tunnelling Underground Space Technol. 42 (May): 59–66. https://doi.org/10.1016/j.tust.2014.02.004.
Li, X. G., and D. J. Yuan. 2012. “Response of a double-decked metro tunnel to shield driving of twin closely under-crossing tunnels.” Tunnelling Underground Space Technol. 28 (Mar): 18–30. https://doi.org/10.1016/j.tust.2011.08.005.
Li, Y. S., J. S. Yang, K. E. Zhang, C. B. Huang, and Y. N. Ma. 2013. “Surface subsidence caused by construction of large diameter curved jacking-pipes in pipe-roof pre-construction method.” [In Chinese.] J. Cent. South Univ. (Sci. Technol.) 44 (11): 4687–4693.
Liao, H. J., and M. Cheng. 1996. “Construction of a pipe roofed underpass below groundwater table.” Proc. ICE-Geotech. Eng. 119 (4): 202–210. https://doi.org/10.1680/igeng.1996.28756.
Liao, S. M., J. H. Liu, R. L. Wang, and Z. M. Li. 2009. “Shield tunneling and environment protection in Shanghai soft ground.” Tunnelling Underground Space Technol. 24 (4): 454–465. https://doi.org/10.1016/j.tust.2008.12.005.
Liu, J., B. Ma, and Y. Cheng. 2018. “Design of the Gongbei tunnel using a very large cross-section pipe-roof and soil freezing method.” Tunnelling Underground Space Technol. 72 (Feb): 28–40. https://doi.org/10.1016/j.tust.2017.11.012.
Ma, B. S. 2008. The science of trenchless engineering. Beijing: China Communications Press.
Marshall, A. M., A. Klar, and R. J. Mair. 2010. “Tunneling beneath buried pipes: View of soil strain and its effect on pipeline behavior.” J. Geotech. Geoenviron. Eng. 136 (12): 1664–1672. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000390.
McGuigan, B. L., and A. J. Valsangkar. 2011. “Field monitoring and analysis of twin 3660 mm inside diameter induced trench culverts installed under 21.7 m of fill.” Can. Geotech. J. 48 (5): 781–794.
Meskele, T., and A. W. Stuedlein. 2013. “Analysis of a 610-mm-diameter pipe installed using pipe ramming.” J. Perform. Constr. Facil. 28 (4): 1–7. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000463.
Milligan, G. E., and P. Norris. 1999. “Pipe-soil interaction during pipe jacking.” Proc. ICE-Geotech. Eng. 137 (1): 27–44. https://doi.org/10.1680/gt.1999.370104.
Milligan, G. W. E. 1996. “Site-based research in pipe jacking—Objectives, procedures and a case history.” Tunnelling Underground Space Technol. 11 (1): 3–24. https://doi.org/10.1016/0886-7798(95)00041-0.
Moh, Z. C., K. I. Hsiung, P. C. Huang, and R. N. Hwang. 1999. “Underpass beneath Taipei international airport.” In Proc., Conf. on New Frontiers and Challenges, 1525–1541. Bangkok, VA: Asian Institute of Technology.
Musso, G. 1979. “Jacked pipe provides roof for underground construction in busy urban area.” Civ. Eng. 49 (11): 79–82.
Ong, D. E. L., and C. S. Choo. 2016. “Back-analysis and finite element modeling of jacking forces in weathered rocks.” Tunnelling Underground Space Technol. 51 (4): 1–10. https://doi.org/10.1016/j.tust.2015.10.014.
Pellet-Beacour, A. L., and R. Kastner. 2002. “Experimental and analytical study of friction forces during microtunneling operations.” Tunnelling Underground Space Technol. 17 (1): 83–97.
Rhodes, G. W., and J. L. Kauschinger. 1996. “Microtunnelling provides structural support for large tunnels with shallow cover.” In North American tunneling, 443–449. Rotterdam, Netherlands: A.A. Balkema.
Shou, K., J. Yen, and M. Liu. 2010. “On the frictional property of lubricants and its impact on jacking force and soil–pipe interaction of pipe jacking.” Tunnelling Underground Space Technol. 25 (4): 469–477. https://doi.org/10.1016/j.tust.2010.02.009.
Shou, K. J., and J. M. Jiang. 2010. “A study of jacking force for a curved pipe jacking.” J. Rock Mech. Geotech. Eng. 2 (4): 298–304.
Sofianos, A. I., P. Loukas, and C. Chantzakos. 2004. “Pipe jacking a sewer under Athens.” Tunnelling Underground Space Technol. 19 (2): 193–203. https://doi.org/10.1016/S0886-7798(03)00108-1.
Stein, D., K. Mollers, and R. Bielecki. 1989. Microtunneling, 352. Berlin: Ernst et Sohn.
Sugimoto, M., and A. Asanprakit. 2010. “Stack pipe model for pipe jacking method.” J. Constr. Eng. Manage. 136 (6): 683–692. https://doi.org/10.1061/(ASCE)CO.1943-7862.0000172.
Wang, H., W.-M. Qin, and Y.-Y. Jiao. 2013. “Stability assessment for highway with large-span box culvert jacking underneath: A case study.” Can. Geotech. J. 50 (6): 585–594. https://doi.org/10.1139/cgj-2012-0334.
Yen, J., and K. Shou. 2015. “Numerical simulation for the estimation the jacking force of pipe jacking.” Tunnelling Underground Space Technol. 49 (4): 218–229. https://doi.org/10.1016/j.tust.2015.04.018.
Zhang, D., B. Liu, and Y. Qin. 2016a. “Construction of a large-section long pedestrian underpass using pipe jacking in muddy silty clay: A case study.” Tunnelling Underground Space Technol. 60 (Nov): 151–164. https://doi.org/10.1016/j.tust.2016.08.009.
Zhang, H., P. Zhang, W. Zhou, S. Dong, and B. Ma. 2016b. “A new model to predict soil pressure acting on deep burial jacked pipes.” Tunnelling Underground Space Technol. 60 (Nov): 183–196. https://doi.org/10.1016/j.tust.2016.09.005.
Zhang, P., B. S. Ma, C. Zeng, H. M. Xie, X. Li, and D. W. Wang. 2016c. “Key techniques for the largest curved pipe jacking roof to date: A case study of Gongbei tunnel.” Tunnelling Underground Space Technol. 59 (Oct): 134–145. https://doi.org/10.1016/j.tust.2016.07.001.
Zhen, L., J. J. Chen, P. Z. Qiao, and J. H. Wang. 2014. “Analysis and remedial treatment of a steel pipe-jacking accident in complex underground environment.” Eng. Struct. 59 (Feb): 210–219. https://doi.org/10.1016/j.engstruct.2013.10.025.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jun 11, 2020
Accepted: May 18, 2021
Published online: Sep 15, 2021
Published in print: Nov 1, 2021
Discussion open until: Feb 15, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Yazheng Wang, Dingli Zhang, Qian Fang, Xiang Liu, Jianchen Wang, Analytical Solution on Ground Deformation Caused by Parallel Construction of Rectangular Pipe Jacking, Applied Sciences, 10.3390/app12073298, 12, 7, (3298), (2022).
- Kaixin Liu, Anfeng Xiao, Peng Zhang, Hao Zhou, Zhihan Chen, Tianshuo Xu, Baosong Ma, Hui Ai, Qiang Wang, Study on mechanical response of steel pipe jacking considering the effect of pipe sticking, Tunnelling and Underground Space Technology, 10.1016/j.tust.2022.104617, 127, (104617), (2022).