Physical Model Tests of Half-Scale Geosynthetic Reinforced Soil Bridge Abutments. I: Static Loading
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 145, Issue 11
Abstract
This paper presents experimental results from physical model tests on four half-scale geosynthetic reinforced soil (GRS) bridge abutment specimens constructed using well-graded angular backfill sand, modular facing blocks, and uniaxial geogrid reinforcement to investigate the effects of applied surcharge stress, reinforcement vertical spacing, and reinforcement tensile stiffness for working stress, static loading conditions. Facing displacements increased for the upper section of the walls after the application of surcharge stress and were greater for larger reinforcement vertical spacing and reduced reinforcement tensile stiffness. Bridge seat settlements were proportional to the applied surcharge stress, strongly affected by larger reinforcement vertical spacing, and only slightly affected by reduced reinforcement tensile stiffness. Measured vertical and lateral soil stresses generally were lower than calculated values for static loading conditions. The maximum tensile strain in each reinforcement layer occurred near the facing block connection for lower layers and under the bridge seat for higher layers. A companion paper presents experimental results for the same GRS bridge abutment specimens under dynamic loading conditions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support for this study provided by the California Department of Transportation (Caltrans) Project 65A0556 with Federal Highway Administration (FHWA) Pooled Fund Project 1892AEA is gratefully acknowledged. The authors thank Dr. Charles Sikorsky and Kathryn Griswell of Caltrans for their support and assistance with the project. The first author gratefully acknowledges a GSI Fellowship provided by the Geosynthetic Institute. The authors also thank the staff and undergraduate research assistants at the UCSD Powell Structural Laboratories for their help with the experimental work. The geogrid used in this study was provided by the Tensar International Corporation, Inc.
References
AASHTO. 2012. AASHTO LRFD bridge design specifications. 6th ed. Washington, DC: AASHTO.
Abu-Farsakh, M., A. Ardah, and G. Voyiadjis. 2018. “3D finite element analysis of the geosynthetic reinforced soil-integrated bridge system (GRS-IBS) under different loading condition.” Transp. Geotech. 15 (Jun): 70–83. https://doi.org/10.1016/j.trgeo.2018.04.002.
Abu-Hejleh, N., J. G. Zornberg, T. Wang, and J. Watcharamonthein. 2002. “Monitored displacements of unique geosynthetic-reinforced soil bridge abutments.” Geosynthetics Int. 9 (1): 71–95. https://doi.org/10.1680/gein.9.0211.
Adams, M. 1997. “Performance of a prestrained geosynthetic reinforced soil bridge pier.” In Mechanically stabilized backfill, 35–53. Rotterdam, Netherlands: A.A. Balkema.
Adams, M., J. Nicks, T. Stabile, J. Wu, W. Schlatter, and J. Hartmann. 2011a. Geosynthetic reinforced soil integrated bridge system interim implementation guide. Washington, DC: USDOT.
Adams, M., J. Nicks, T. Stabile, J. Wu, W. Schlatter, and J. Hartmann. 2011b. Geosynthetic reinforced soil integrated bridge system synthesis report. Washington, DC: USDOT.
Adams, M. T., P. S. Ooi, and J. E. Nicks. 2014. “Mini-pier testing to estimate performance of full-scale geosynthetic reinforced soil bridge abutments.” Geotech. Test. J. 37 (5): 884–894. https://doi.org/10.1520/GTJ20140007.
Allen, T. M., and R. J. Bathurst. 2014a. “Design and performance of 6.3-m-high, block-faced geogrid wall designed using K-stiffness method.” J. Geotech. Geoenviron. Eng. 140 (2): 04013016. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001013.
Allen, T. M., and R. J. Bathurst. 2014b. “Performance of an 11 m high block-faced geogrid wall designed using the K-stiffness method.” Can. Geotech. J. 51 (1): 16–29. https://doi.org/10.1139/cgj-2013-0261.
Ambauen, S., B. Leshchinsky, Y. Xie, and D. Rayamajhi. 2016. “Service-state behavior of reinforced soil walls supporting spread footings: A parametric study using finite-element analysis.” Geosynthetics Int. 23 (3): 156–170. https://doi.org/10.1680/jgein.15.00039.
Ardah, A., M. Abu-Farsakh, and G. Voyiadjis. 2017. “Numerical evaluation of the performance of a geosynthetic reinforced soil-integrated bridge system (GRS-IBS) under different loading conditions.” Geotext. Geomembr. 45 (6): 558–569. https://doi.org/10.1016/j.geotexmem.2017.07.005.
ASTM. 2015. Standard test method for determining tensile properties of geogrids by the single or multi-rib tensile method. ASTM D6637. West Conshohocken, PA: ASTM.
Bathurst, R. J., T. M. Allen, and D. L. Walters. 2002. “Short-term strain and deformation behavior of geosynthetic walls at working stress conditions.” Geosynthetics Int. 9 (5–6): 451–482. https://doi.org/10.1680/gein.9.0225.
Bathurst, R. J., A. Nernheim, D. L. Walters, T. M. Allen, P. Burgess, and D. D. Saunders. 2009. “Influence of reinforcement tensile stiffness and compaction on the performance of four geosynthetic reinforced soil walls.” Geosynthetics Int. 16 (1): 43–59. https://doi.org/10.1680/gein.2009.16.1.43.
Bathurst, R. J., N. Vlachopoulos, D. L. Walters, P. G. Burgess, and T. M. Allen. 2006. “The influence of facing stiffness on the performance of two geosynthetic reinforced soil retaining walls.” Can. Geosynthetics J. 43 (12): 1225–1237. https://doi.org/10.1139/t06-076.
Budge, A. S., D. D. Dasenbrock, D. J. Mattison, G. K. Bryant, A. T. Grosser, M. Adams, and J. Nicks. 2014. “Instrumentation and early performance of a large grade GRS-IBS wall.” In Proc., Geo-Congress 2014, 4213–4227. Reston, VA: ASCE.
Ehrlich, M., and S. H. Mirmoradi. 2013. “Evaluation of the effects of facing stiffness and toe resistance on the behavior of GRS walls.” Geotext. Geomembr. 40 (Oct): 28–36. https://doi.org/10.1016/j.geotexmem.2013.07.012.
Ehrlich, M., S. H. Mirmoradi, and R. P. Saramago. 2012. “Evaluation of the effect of compaction on the behavior of geosynthetic-reinforced soil walls.” Geotext. Geomembr. 34 (Oct): 108–115. https://doi.org/10.1016/j.geotexmem.2012.05.005.
Gotteland, P., J. P. Gourc, and P. Villard. 1997. “Geosynthetic reinforced structures as bridge abutments: Full scale experimentation and comparison with modelisations.” In Mechanically stabilized backfill, 25–34. Rotterdam, Netherlands: A.A. Balkema.
Helwany, S. M. B., J. T. H. Wu, and B. Froessl. 2003. “GRS bridge abutments—An effective means to alleviate bridge approach settlement.” Geotext. Geomembr. 21 (3): 177–196. https://doi.org/10.1016/S0266-1144(03)00004-9.
Helwany, S. M. B., J. T. H. Wu, and A. Kitsabunnarat. 2007. “Simulating the behavior of GRS bridge abutments.” J. Geotech. Geoenviron. Eng. 133 (10): 1229–1240. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:10(1229).
Helwany, S. M. B., J. T. H. Wu, and P. Meinholz. 2012. Seismic design of geosynthetic-reinforced soil bridge abutments with modular block facing. NCHRP Web-Only Document 187. Washington, DC: Transportation Research Board.
Iwamoto, M. K., P. S. Ooi, M. T. Adams, and J. E. Nicks. 2015. “Composite properties from instrumented load tests on mini-piers reinforced with geotextiles.” Geotech. Test. J. 38 (4): 397–408. https://doi.org/10.1520/GTJ20140181.
Jiang, Y., J. Han, R. L. Parsons, and J. Brennan. 2016. “Field instrumentation and evaluation of modular-block MSE walls with secondary geogrid layers.” J. Geotech. Geoenviron. Eng. 142 (12): 05016002. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001573.
Ketchart, K., and J. T. H. Wu. 1997. “Performance of geosynthetic-reinforced soil bridge pier and abutment, Denver, Colorado, USA.” In Mechanically stabilized backfill, 101–116. Rotterdam, Netherlands: A.A. Balkema.
Khosravi, A., M. Ghayoomi, J. S. McCartney, and H.-Y. Ko. 2010. “Impact of effective stress on the dynamic shear modulus of unsaturated sands.” In Proc., GeoFlorida 2010: Advances in Analysis, Modeling and Design, 410–419. Reston, VA: ASCE.
Lee, K. Z. Z., and J. T. H. Wu. 2004. “A synthesis of case histories on GRS bridge-supporting structures with flexible facing.” Geotext. Geomembr. 22 (4): 181–204. https://doi.org/10.1016/j.geotexmem.2004.03.002.
Leshchinsky, B., and Y. Xie. 2015. “MSE walls as bridge abutments: Optimal reinforcement density.” Geotext. Geomembr. 43 (2): 128–138. https://doi.org/10.1016/j.geotexmem.2015.01.002.
Lu, N., J. W. Godt, and D. T. Wu. 2010. “A closed-form equation for effective stress in unsaturated soil.” Water Resour. Res. 46 (5): W05515. https://doi.org/10.1029/2009WR008646.
McCartney, J. S., P. B. Shing, Y. Zheng, W. Rong, and P. J. Fox. 2018. Interaction of MSE abutments with bridge superstructures under seismic loading—Shaking table tests. Sacramento, CA: California DOT.
Mirmoradi, S. H., and M. Ehrlich. 2017. “Effects of facing, reinforcement tensile stiffness, toe resistance, and height on reinforced walls.” Geotext. Geomembr. 45 (1): 67–76. https://doi.org/10.1016/j.geotexmem.2016.07.006.
Nicks, J. E., M. T. Adams, P. S. K. Ooi, and T. Stabile. 2013. Geosynthetic reinforced soil performance testing—Axial load deformation relationships. Washington, DC: USDOT.
Nicks, J. E., D. Esmaili, and M. T. Adams. 2016. “Deformations of geosynthetic reinforced soil under bridge service loads.” Geotext. Geomembr. 44 (4): 641–653. https://doi.org/10.1016/j.geotexmem.2016.03.005.
Rong, W., Y. Zheng, J. S. McCartney, and P. J. Fox. 2017. “3D deformation behavior of geosynthetic reinforced soil bridge abutments.” In Proc., Geotechnical Frontiers 2017, 44–53. Reston, VA: ASCE.
Runser, D., P. J. Fox, and P. L. Bourdeau. 2001. “Field performance of a 17 m-high reinforced soil retaining wall.” Geosynth. Int. 8 (5): 367–391. https://doi.org/10.1680/gein.8.0200.
Saghebfar, M., M. Abu-Farsakh, A. Ardah, and Q. Chen. 2017. “Performance monitoring of geosynthetic reinforced soil integrated bridge system (GRS-IBS) in Louisiana.” Geotext. Geomembr. 45 (2): 34–47. https://doi.org/10.1016/j.geotexmem.2016.11.004.
Shen, P., J. Han, J. Zornberg, A. Morsy, D. Leshchinsky, B. F. Tanyu, and C. Xu. 2019. “Two and three-dimensional numerical analyses of geosynthetic-reinforced soil (GRS) piers.” Geotext. Geomembr. 47 (3): 352–368. https://doi.org/10.1016/j.geotexmem.2019.01.010.
Trautner, C. A., Y. Zheng, J. S. McCartney, and T. C. Hutchinson. 2018. “An approach for shake table performance evaluation during repair and retrofit actions.” Earthquake Eng. Struct. Dyn. 47 (1): 131–146. https://doi.org/10.1002/eqe.2942.
Vahedifard, F., B. Leshchinsky, K. Mortezaei, and N. Lu. 2015. “Active earth pressures for unsaturated retaining structures.” J. Geotech. Geoenviron. Eng. 141 (11): 04015048. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001356.
Vahedifard, F., B. Leshchinsky, S. Sehat, and D. Leshchinsky. 2014. “Impact of cohesion on seismic design of geosynthetic-reinforced earth structures.” J. Geotech. Geoenviron. Eng. 140 (6): 04014016. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001099.
Van Genuchten, M. T. 1980. “A closed-form equation for predicting the hydraulic conductivity of unsaturated soils.” Soil Sci. Soc. Am. J. 44 (5): 892–898. https://doi.org/10.2136/sssaj1980.03615995004400050002x.
Won, G. W., T. Hull, and L. De Ambrosis. 1996. “Performance of a geosynthetic segmental block wall structure to support bridge abutments.” In Vol. 1 of Earth reinforcement, 543–548. Rotterdam, Netherlands: A.A. Balkema.
Wu, J. T. H., K. Ketchart, and M. Adams. 2001. GRS bridge piers and abutments. Washington, DC: USDOT.
Wu, J. T. H., K. Z. Z. Lee, S. B. Helwany, and K. Ketchart. 2006. Design and construction guidelines for geosynthetic-reinforced soil bridge abutments with a flexible facing. Washington, DC: Transportation Research Board.
Xu, C., C. Liang, and P. Shen. 2019. “Experimental and theoretical studies on the ultimate bearing capacity of geogrid-reinforced sand.” Geotext. Geomembr. 47 (3): 417–428. https://doi.org/10.1016/j.geotexmem.2019.01.003.
Zheng, Y. 2017. “Numerical simulations and shaking table tests of geosynthetic reinforced soil bridge abutments.” Ph.D. dissertation, Dept. of Structural Engineering, Univ. of California, San Diego.
Zheng, Y., and P. J. Fox. 2016. “Numerical investigation of geosynthetic-reinforced soil bridge abutments under static loading.” J. Geotech. Geoenviron. Eng. 142 (5): 04016004. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001452.
Zheng, Y., and P. J. Fox. 2017. “Numerical investigation of the geosynthetic reinforced soil-integrated bridge system under static loading.” J. Geotech. Geoenviron. Eng. 143 (6): 04017008. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001665.
Zheng, Y., P. J. Fox, and J. S. McCartney. 2018a. “Numerical simulation of deformation and failure behavior of geosynthetic reinforced soil bridge abutments.” J. Geotech. Geoenviron. Eng. 144 (7): 04018037. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001893.
Zheng, Y., P. J. Fox, and J. S. McCartney. 2018b. “Numerical simulation of deformation response of geosynthetic reinforced soil mini-piers.” Geosynthetics Int. 25 (3): 271–286. https://doi.org/10.1680/jgein.18.00007.
Zheng, Y., J. S. McCartney, P. B. Shing, and P. J. Fox. 2018c. “Transverse shaking table test of a half-scale geosynthetic reinforced soil bridge abutment.” Geosynthetics Int. 25 (6): 582–598. https://doi.org/10.1680/jgein.18.00019.
Zheng, Y., J. S. McCartney, P. B. Shing, and P. J. Fox. 2019. “Physical model tests of half-scale geosynthetic reinforced soil bridge abutments. II: Dynamic loading.” J. Geotech. Geoenviron. Eng. 145 (11): 04019095. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002158.
Zheng, Y., A. C. Sander, W. Rong, P. J. Fox, P. B. Shing, and J. S. McCartney. 2018d. “Shaking table test of a half-scale geosynthetic-reinforced soil bridge abutment.” Geotech. Test. J. 41 (1): 171–192. https://doi.org/10.1520/GTJ20160268.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jun 4, 2018
Accepted: May 29, 2019
Published online: Aug 26, 2019
Published in print: Nov 1, 2019
Discussion open until: Jan 26, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.