Effect of Temperature on Geotechnical Properties of Recycled Asphalt Shingle Mixtures
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 141, Issue 2
Abstract
Shear strength, compressibility, and hydraulic conductivity of recycled asphalt shingles (RASs) mixed with bottom ash (BA) or stabilized with self-cementing fly ash (FA) were evaluated in a systematic manner at temperatures ranging from 5 to 35°C, representing seasonal field temperature variation. Increasing temperature reduced the shear strength and increased the compressibility and hydraulic conductivity of compacted RAS-BA and RAS-FA mixtures. When the temperature increased from 5 to 35°C, the effective friction angle () of the compacted RAS-BA mixture containing 25% RAS decreased from 41 to 35°. The mixture containing 50% RASs decreased from 41 to 29°. The of the compacted RAS-FA mixture containing 20% FA decreased from 46 to 26°; however, the effective cohesion () increased from 45 to 70 kPa, and the compressive strength remained higher than that of compacted sand. In contrast, the secondary compression ratio () increased with temperature. The of the RAS-BA mixture is an exponential function of temperature. Thermal cycling induced thermal precompression to the compacted RAS-BA and RAS-FA mixtures and significantly reduced the compressibility. Thermal precompression reduced for the compacted RAS-BA mixture containing 25% RASs from 0.0078 to 0.0004 and that of the RAS-FA mixture from 0.0016 to 0.0002, which are comparable with for compacted sand (). Therefore, to reduce long-term settlement of an embankment made with materials containing RAS, construction is recommended during warm seasons. In this way, most settlement occurs during construction, and settlement during service life of the embankment becomes negligible. The hydraulic conductivity of the compacted RAS-BA and RAS-FA mixtures increased with increasing temperature, which is beneficial to drainage capacity of structural fills containing RASs.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this research was provided by the Recycled Material Resource Center (RMRC) and Solid Waste Research Program (SWRP) at the University of Wisconsin–Madison. The authors also greatly appreciate B. R. Amon & Sons for providing recycled asphalt shingles for this research.
References
Abuel-Naga, H. M., Bergado, D. T., and Lim, B. F. (2007). “Effect of temperature on shear strength and yielding behavior of soft Bangkok clay.” Soils Found., 47(3), 423–436.
Akisetty, C. K., Lee, S.-J., and Amirkhanian, S. N. (2009). “Effects of compaction temperature on volumetric properties of rubberized mixes containing warm-mix additives.” J. Mater. Civ. Eng., 409–415.
Andersen, K. H., and Schjetne, K. (2013). “Database of friction angles of sand and consolidation characteristics of sand, silt, and clay.” J. Geotech. Geoenviron. Eng., 1140–1155.
ASTM. (1963). “Standard test method for particle-size analysis of soils.” D422-63, West Conshohocken, PA.
ASTM. (1995). “Standard test methods for measurement of hydraulic conductivity of saturated porous materials using a flexible wall permeameter.” D5084-03, West Conshohocken, PA.
ASTM. (2000a). “Standard test methods for laboratory compaction characteristics of soil using standard effort ( ()).” D698-00a, West Conshohocken, PA.
ASTM. (2000b). “Standard test methods for specific gravity of soil solids by water pycnometer.” D854-00, West Conshohocken, PA.
ASTM. (2004). “Standard test method for consolidated undrained triaxial compression test for cohesive soils.” D4767-04, West Conshohocken, PA.
ASTM. (2006). “Standard specification for fly ash and other pozzolans for use with lime for soil stabilization.” C593-06, West Conshohocken, PA.
ASTM. (2009). “Standard viscosity-temperature charts for asphalts.” D2493-09, West Conshohocken, PA.
Azari, H., McCuen, R. H., and Stuart, K. D. (2003). “Optimum compaction temperature for modified binders.” J. Transp. Eng., 531–537.
Burghignoli, A., Desideri, A., and Miliziano, S. (2000). “A laboratory study on the thermomechanical behaviour of clayey soils.” Can. Geotech. J., 37(4), 764–780.
Campanella, R. G., and Mitchell, J. K. (1968). “Influence of temperature variations on soil behavior.” J. Soil Mech. and Found. Div., 94(3), 609–734.
Cao, L., Dong, L., and Sun, L. (2009). “Permanent deformation characteristic of asphalt mixture considering pavement temperature distribution.” Proc., ICCTP 2009: Critical Issues in Transportation Systems Planning, Development, and Management, Y. Wang, P. Yi, S. An, H. Wang, eds, ASCE, Reston, VA, 1–8.
Carman, P. C. (1937). “Fluid flow through granular beds.” Trans. Inst. Chem. Eng., London, 15, 150–166.
Carpenter, A. C., Gardner, K. H., Fopiano, J., Benson, C. H., and Edil, T. B. (2007). “Life cycle based risk assessment of recycled materials in roadway construction.” Waste Manag., 27(10), 1458–1464.
Cekerevac, C., and Laloui, L. (2004). “Experimental study of thermal effects on the mechanical behaviour of a clay.” Int. J. Numer. Anal. Methods Geomech., 28(3), 209–228.
Chen, X., Huang, B., and Xu, Z. (2006). “Uniaxial penetration testing for shear resistance of hot-mix asphalt mixtures.” Transportation Research Record 1970, Transportation Research Board, Washington, DC, 116–125.
De Bruyn, D., and Thimus, J. F. (1996). “The influence of temperature on mechanical characteristics of Boom clay: The results of an initial laboratory programme.” Eng. Geol., 41(1–4), 117–126.
Delage, P., Sultan, N., and Cui, Y. J. (2000). “On the thermal consolidation of Boom clay.” Can. Geotech. J., 37(2), 343–354.
Edil, T. B., and Fox, P. J. (1994). “Field test of thermal precompression.” Proc., Vertical and Horizontal Deformations of Foundations and Embankments, Geotechnical special publication 40, A. T. Yeung and G. Y. Félio, eds., ASCE, Reston, VA, 1274–1286.
Fox, P. J., and Edil, T. B. (1996). “Effects of stress and temperature on secondary compression of peat.” Can. Geotech. J., 33(3), 405–415.
Fu, P., and Harvey, J. T. (2007). “Temperature sensitivity of foamed asphalt mix stiffness: Field and lab study.” Int. J. Pavement Eng., 8(2), 137–145.
Gambatese, J. A., and Rajendran, S. (2005). “Sustainable roadway construction: Energy consumption and material waste generation of roadways.” Proc., Construction Research Congress 2005: Broadening Perspectives, I. D. Tommelein, ed., ASCE, Reston, VA, 1–13.
Graham, J., Tanaka, N., Crilly, T., and Alfaro, M. (2001). “Modified Cam-Clay modelling of temperature effects in clay.” Can. Geotech. J., 38(3), 608–621.
Hanson, J. L. (1996). “Thermal precompression of peat.” Ph.D. thesis, Univ. of Wisconsin–Madison, Madison, WI.
Holtz, R. D., Kovacs, W. D., and Sheahan, T. C. (2011). An introduction to geotechnical engineering, Pearson Education, Upper Saddle River, NJ.
Houston, S. L., Houston, W. N., and Williams, N. D. (1985). “Thermo-mechanical behavior of seafloor sediments.” J. Geotech. Engrg., 1249–1263.
Hueckel, T., and Baldi, G. (1990). “Thermoplasticity of saturated clays: Experimental constitutive study.” J. Geotech. Engrg., 1778–1796.
Jun, Y., Haoran, Z., and Zhiwei, C. (2009). “Evaluation on the shear performance of asphalt mixture through triaxial shear test.” Advanced testing and characterization of bituminous materials, Taylor & Francis, London, 575–583.
Kilbert, C. J. (2002). “Policy instruments for a sustainable built environment.” J. Land Use Environ. Law, 17(2), 379–394.
Korson, L., Hansen, W. D., and Millero, F. J. (1969). “Viscosity of water at various temperatures.” J. Phys. Chem., 73(1), 34–39.
Krivit, D. (2007). Recycling of tear-off shingles: Best practices guide, Construction Materials Recycling Association, Aurora, IL.
LabVIEW 8.5 [Computer software]. Austin, TX, National Instruments.
Ladd, C. C., Foote, R., Ishihara, K., Schlosser, F., and Poulos, H. G. (1977). “Stress-deformation and strength characteristics.” Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, Vol. 2, Japanese Society of Soil Mechanics and Foundation Engineering, Tokyo, 421–494.
Lade, P. V., and Liu, C.-T. (1998). “Experimental study of drained creep behavior of sand.” J. Eng. Mech., 912–920.
Lambe, T. W., and Whitman, R. V. (1969). Soil mechanics, Wiley, New York.
Lee, J. C., Edil, T. B., Tinjum, J. M., and Benson, C. H. (2010). “Quantitative assessment of environmental and economic benefits of using recycled construction materials in highway construction.” Transporation Research Record 2158, Transportation Research Board, Washington, DC, 138–142.
Lee, S.-J., Amirkhanian, S. N., Putman, B. J., and Kim, K. W. (2007). “Laboratory study of the effects of compaction on the volumetric and rutting properties of CRM asphalt mixtures.” J. Mater. Civ. Eng., 1079–1089.
Mesri, G., and Castro, A. (1987). “ concept and during secondary compression.” J. Geotech. Engrg., 230–247.
Mesri, G., Feng, T. W., and Benak, J. M. (1990). “Postdensification penetration resistance of clean sands.” J. Geotech. Engrg., 1095–1115.
Mesri, G., and Vardhanabhuti, B. (2009). “Compression of granular materials.” Can. Geotech. J., 46(4), 369–392.
Mitchell, J. K., McMillan, J. C., Green, S. L., and Sisson, R. C. (1982). “Field testing of cable backfill systems.” Underground cable thermal backfill, S. A. Boogs, et al., eds., Pergamon Press, New York, 19–33.
Mitchell, J. K., and Soga, K. (2005). Fundamentals of soil behavior, Wiley, New York.
Palit, S. K., Reddy, K. S., and Pandey, B. B. (2004). “Laboratory evaluation of crumb rubber modified asphalt mixes.” J. Mater. Civ. Eng., 45–53.
Plum, R. L., and Esrig, M. I. (1969). “Some temperature effects on soil compressibility and pore water pressure.” Special Rep. No. 103, Highway Research Board, Washington, DC, 231–242.
Rao, S. M., and Shivananda, P. (2005). “Role of curing temperature in progress of lime-soil reactions.” Geotech. Geol. Eng., 23(1), 79–85.
Roberts, F. L., Kandhal, P. S., Brown, E. R., Lee, D. Y., and Kennedy, T. W. (1996). Hot mix asphalt materials, mixture design, and construction, National Asphalt Paving Association Education Foundation, Lanham, MD.
Sanchez-Alonso, E., Vega-Zamanillo, A., and Castro-Fresno, D. (2012). “Effect of type of compaction on mechanical properties in warm-mix asphalts.” J. Mater. Civ. Eng., 1043–1049.
Sengoz, B., and Topal, A. (2004). “Use of asphalt roofing shingle waste in HMA.” Construct. Build. Mater., 19(5), 338–346.
Slegel, D. L., and Davis, L. R. (1977). “Transient heat and mass transfer in soils in the vicinity of heated porous pipes.” J. Heat Transfer, 99(4), 541–621.
Soleimanbeigi, A. (2012). “Evaluation of recycled asphalt shingles as structural fill.” Ph.D. thesis, Univ. of Wisconsin–Madison, Madison, WI.
Soleimanbeigi, A., Edil, T., and Benson, C. (2013). “Evaluation of fly ash stabilization of recycled asphalt shingles for use in structural fills.” J. Mater. Civ. Eng., 94–104.
Soleimanbeigi, A., Edil, T. B., and Benson, C. H. (2012). “Recycled asphalt shingles mixed with granular byproducts as structural fills.” J. ASTM Int., 9(1), JAI103766.
Soleimanbeigi, A., Edil, T. B., and Benson, C. H. (2014). “Creep response of recycled asphalt shingles.” Can. Geotech. J., 51(1), 103–114.
Sondag, M. S., Chadbourn, B. A., and Drescher, A. (2002). “Investigation of recycled asphalt pavement (RAP) mixtures.” Rep. No. MN/RC–2002-15, Minnesota DOT, St. Paul, MN.
Tayebali, A. A., Tsai, B.-W., and Monismith, C. L. (1994). “Stiffness of asphalt-aggregate mixes.” Rep. No. SHRP-A-388, Strategic Highway Research Program, National Research Council, Washington, DC.
Taylor, D. W. (1948). Fundamentals of soil mechanics, Wiley, New York.
Terzaghi, K., Peck, R. B., and Mesri, G. (1996). Soil mechanics in engineering practice, 3rd Ed., Wiley, New York.
Townsend, T., Powell, J., and Xu, C. (2007). Environmental issues associated with asphalt shingle recycling, U.S. EPA Innovations Workgroup, Construction Materials Recycling Association, Aurora, IL.
U.S. EPA. (2009). “Potential for reducing greenhouse gas emissions in the construction sector.” Sector strategies, 〈http://www.epa.gov/sectors/pdf/construction-sector-report.pdf〉 (Nov. 15, 2012).
U.S. Navy. (1986). “Design manual—Soil mechanics, foundations, and earth structures.” NAVFAC DM-7, Dept. of the Navy, Washington, DC.
Veisi, M., Chittoori, B., Celaya, M., Nazarian, S., Puppala, A. J., and Solis, C. (2010). “Accelerated stabilization design of subgrade soils.” Research Rep. FHWA/TX 06/0-5569-1, Center for Transportation Infrastructure Systems, Univ. of Texas at El Paso, El Paso, TX.
Vermont Agency of Natural Resources (VANR). (1999). “Recycled asphalt shingles in road applications: An overview of the state of practice.” 〈http://www.anr.state.vt.us/dec/wastediv/recycling/shingles.pdf〉 (Jun. 9 2012).
Wang, H.-N., Liu, X.-J., and Hao, P.-W. (2008). “Evaluating the shear resistance of hot mix asphalt by the direct shear test.” J. Test. Eval., 36(6), 1–7.
Warner, J. D. (2007). “The beneficial reuse of asphalt shingles in roadway construction.” M.Sc. thesis, Univ. of Wisconsin–Madison, Madison, WI.
West, R. C., Watson, D. E., Turner, P. A., and Casola, J. R. (2010). “Mixing and compaction temperatures of asphalt binders in hot-mix asphalt.” Rep. No. 648, National Cooperative Highway Research Program, Transportation Research Board, Washington, DC.
Wright, P. H. (1996). Highway engineering, Wiley, New York.
Zickell, A. J. (2003). “Asbestos analysis of post consumer asphalt shingles.” Technical Rep. No. 41, Technical Research Program, Chelsea Center for Recycling and Economic Development, Chelsea, MA.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Dec 2, 2013
Accepted: Sep 15, 2014
Published online: Oct 14, 2014
Published in print: Feb 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.