Size Distribution of Coarse-Grained Soil by Sedimaging
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 140, Issue 4
Abstract
An image-based method has been developed for determination of particle-size distributions of coarse-grained soils in the 0.075–2.0 mm range. The percentage of fines is also determined. The test is referred to as sedimaging because it analyzes an image of a soil that has been rapidly sedimented through water to sort the particles by size. The sorting facilitates image analysis based on wavelet transformation. This paper details the sedimaging hardware, image analysis method, and test procedures. Parallel sedimaging and sieving tests on nine soils of different colors, gradations, and particle shapes showed nearly identical results. Sedimaging holds several advantages over sieving, including decreased testing time, lower energy consumption, less equipment maintenance, and improvement of the work environment.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based on work supported by the National Science Foundation under Grant Nos. CMMI-0900105 and CMMI-1300010 and by the Michigan DOT (MDOT) through Contract No. 2010-0296 Research No. ORE0908. ConeTec Investigations Ltd. and the ConeTec Education Foundation are acknowledged for their support to the Geotechnical Engineering Laboratories at the University of Michigan. The authors thank Richard Endres and Al Robords of the MDOT for their valuable comments. Bob Fischer provided design suggestions and constructed the sedimaging system, Nick Brant assisted with design of the soil accumulator, and Merrick Burch constructed the presegregation system.
References
Bowman, E. T., and Soga, K. (2003). “Creep, ageing and microstructural change in dense granular materials.” Soils Found., 43(4), 107–117.
Bowman, E. T., Soga, K., and Drummond, W. (2001). “Particle shape characterisation using fourier descriptor analysis.” Geotechnique, 51(6), 545–554.
Du, C.-J., and Sun, D.-W. (2004). “Recent development in the applications of image processing techniques for food quality evaluation.” Trends Food Sci. Technol., 15(5), 230–249.
Eremin, S. N. (2006). “Image processing technology in the systems for quality control of sheet metal roll.” Pattern Recognit. Image Anal., 16(1), 127–130.
Fletcher, T., Chandan, C., Masad, E., and Sivakumar, K. (2003). “Aggregate imaging system for characterizing the shape of fine and coarse aggregates.” Transportation Research Record 1832, Transportation Research Board, Washington, DC, 67–77.
Ghalib, A. M., and Hryciw, R. D. (1999). “Soil particle size distribution by mosaic imaging and watershed analysis.” J. Comput. Civ. Eng., 80–87.
Ghalib, A. M., Hryciw, R. D., and Shin, S. (1998). “Image textural analysis and neural networks for characterization of uniform soils.” Proc., Conf. on Computing in Civil Engineering, ASCE, Reston, VA, 671–682.
Hryciw, R. D., and Jung, Y. (2008) “Accounting for void ratio variation in determination of grain size distribution by soil column image processing.” Proc., ASCE GeoInstitute GeoCongress: Characterization, Monitoring, and Modeling of GeoSystems, ASCE, Reston, VA, 966–973.
Hryciw, R. D., Jung, Y., Susila, E., and Ibrahim, A. (2009). “Thin soil layer detection by VisCPT and FEM simulations.” Proc., 17th Int. Conf. on Soil Mechanics and Geotechnical Engineering (ICSMGE), Vol. 2, IOS Press, Fairfax, VA, 1052–1055.
Hryciw, R. D., Ohm, H.-S., and Zhou, J. (2013). “The theoretical basis for optical granulometry by wavelet transformation.” J. Comput. Civ. Eng., (Jul. 25, 2013).
Islam, M. J., Ahmadi, M., and Sid-Ahmed, M. A. (2008). “Image processing techniques for quality inspection of gelatin capsules in pharmaceutical applications.” Proc., 10th Int. Conf. on Control, Automation, Robotics and Vision, IEEE, Piscataway, NJ, 862–867.
Jain, A. K., Ross, A., and Pankanti, S. (2006). “Biometrics: A tool for information security.” IEEE Trans. Inf. Forensics Secur., 1(2), 125–143.
Kuo, C.-Y., and Freeman, R. B. (2000). “Imaging indices for quantification of shape, angularity, and surface texture of aggregates.” Transportation Research Record 1721, Transportation Research Board, Washington, DC, 57–65.
Kuo, C.-Y., Frost, J. D., Lai, J. S., and Wang, L. B. (1996). “Three-dimensional image analysis of aggregate particles from orthogonal projections.” Transportation Research Record 1526, Transportation Research Board, Washington, DC, 98–103.
Mahmoud, E., and Masad, E. (2007). “Experimental methods for the evaluation of aggregate resistance to polishing, abrasion, and breakage.” J. Mater. Civ. Eng., 977–985.
MATLAB R2013a [Computer software]. Natick, MA, MathWorks.
NKRemote 2.6 [Computer software]. Camberley, U.K., Breeze Systems.
Ohm, H.-S. (2013). “Image-based soil particle size and shape characterization.” Ph.D. dissertation, Univ. of Michigan, Ann Arbor, MI.
Ohm, H.-S., and Hryciw, R. D. (2013a). “Enhanced soil characterization through advances in imaging technology.” Proc., 18th Int. Conf. on Soil Mechanics and Geotechnical Engineering (ICSMGE), IOS Press, Fairfax, VA, Vol. 5, 3491–3494.
Ohm, H.-S., and Hryciw, R. D. (2013b). “The translucent segregation table test for sand and gravel particle size distribution.” J. ASTM Geotech Test., 36(4), 592–605.
Ohm, H.-S., Sahadewa, A., Hryciw, R. D., Zekkos, D., and Brant, N. (2013). “Sustainable soil particle size characterization through image analysis.” Geotech. Geol. Eng., 31(6), 1647–1652.
Pham, D. L., Xu, C., and Prince, J. L. (2000). “Current methods in medical image segmentation.” Annu. Rev. Biomed. Eng., 2, 315–337.
Rao, C., and Tutumluer, E. (2000). “Determination of volume of aggregates.” Transportation Research Record 1721, Transportation Research Board, Washington, DC, 73–80.
Raschke, S. A., and Hryciw, R. D. (1997). “Grain-size distribution of granular soils by computer vision.” J. ASTM Geotech Test., 20(4), 433–442.
Shin, S., and Hryciw, R. D. (2004). “Wavelet analysis of soil mass images for particle size determination.” J. Comput. Civ. Eng., 19–27.
Sukumaran, B., and Ashmawy, A. K. (2001). “Quantitative characterisation of the geometry of discrete particles.” Geotechnique, 51(7), 619–627.
Sukumaran, B., and Ashmawy, A. K. (2003). “Influence of inherent particle characteristics on hopper flow rate.” Powder Technol., 138(1), 46–50.
Tutumluer, E., and Pan, T. (2008). “Aggregate morphology affecting strength and permanent deformation behavior of unbound aggregate materials.” J. Mater. Civ. Eng., 617–627.
Wang, W. H., Liu, X. Y., and Sun, Y. (2009). “High-throughput automated injection of individual biological cells.” IEEE Trans. Autom. Sci. Eng., 6(2), 209–219.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Feb 19, 2013
Accepted: Nov 21, 2013
Published online: Dec 23, 2013
Published in print: Apr 1, 2014
Discussion open until: May 23, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.