Development of a New Asymmetric Anchor Plate for Prefabricated Vertical Drain Installation via Centrifuge Model Tests
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 139, Issue 6
Abstract
This study investigates the kinematic behavior of a clay-mandrel-anchor system during the driving-retrieval process and its influence on the installation of prefabricated vertical drains and clay disturbance. In addition, a new anchor plate with an asymmetric shape is proposed as an alternative for improved anchoring performance and clay disturbance mitigation. To investigate the behavior of the clay-mandrel-anchor system, two-dimensional centrifuge model tests were developed and successfully performed to visualize anchoring kinematics and deformation of the clay layer. The tests demonstrated that the asymmetric anchor plate effectively provides an anchoring mechanism and reduces the degree of disturbance. The conventional anchor has potential risk of delayed anchoring and thus unsuccessful installation. While the amount and extent of clay deformation are obviously affected by the protruding length of the anchor plates into the clay, the protrusion length has less influence on the range of the smear zone than the degree of disturbance in the smear zone. The asymmetric anchor considerably reduces the smear effect, as three sides of the mandrel have minimal protrusion length from the center unlike in the conventional anchors.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by Samsung C&T Corporation and partially supported by the National Research Foundation of Korea (NRF) grant of the Korean government (MEST) (No. 2011-0000314). The authors acknowledge Dr. M. Shazzad Hossain and Professor D. White at University of Western Australia for providing inspiration in developing centrifuge models and analyzing digital image data. The authors also appreciate the laboratory support personnel at the KAIST Geotechnical Centrifuge Center.
References
Arulrajah, A., Nikraz, H., and Bo, M. W. (2004). “Factors affecting field instrumentation assessment of marine clay treated with prefabricated vertical drain.” J. Geotextile Geomembr., 22(5), 415–437.
Baligh, M. M. (1985). “Strain path method.” J. Geotech. Engrg., 111(9), 1108–1136.
Bergado, D. T., Balasubramaniam, A. S., Fannin, R. J., and Holtz, R. D. (2002). “Prefabricated vertical drains (PVDs) in soft Bangkok clay: A case study of the New Bangkok International Airport project.” Can. Geotech. J., 39(2), 304–315.
Bo, M. W., Chu, J., Low, B. K., and Choa, V. (2003). Soil improvement: Prefabricated vertical drain technique, Thomson Learning, Singapore.
Chai, J.-C., and Miura, N. (1999). “Investigation of factor affecting vertical drain behavior.” J. Geotech. Geoenviron. Eng., 125(3), 216–226.
Chu, J., Bo, M. W., and Choa, V. (2004). “Practical consideration for using vertical drains in soil improvement project.” J. Geotextile Geomembr., 22(1-2), 101–117.
GeoPIV [Computer software]. Cambridge, U.K., Univ. of Cambridge.
Hansbo, S. (1979). “Consolidation of clay by band-shaped prefabricated vertical drains.” Ground Eng., 12(5), 16–25.
Hansbo, S. (1993). “Band drains.” Ground improvement, M. P. Moseley and K. Kirsch, eds., Taylor & Francis, London, 40–64.
Hird, C. C., and Moseley, V. J. (2000). “Model study of seepage in smear zones around vertical drains in layered soil.” Geotechnique, 50(1), 89–97.
Holtz, R. D. (1987). “Preloading with prefabricated vertical strip drains.” J. Geotextile Geomembr., 6(1-3), 109–131.
Indraratna, B., and Redana, I. W. (1998). “Laboratory determination of smear zone due to vertical drain installation.” J. Geotech. Geoenviron. Eng., 124(2), 180–184.
Indraratna, B., Rujikiatkamjorn, C., Balasubramaniam, A. S., and Wijeyakulasuriya, V. (2005). “Predictions and observations of soft clay foundations stabilized with geosynthetic drains and vacuum surcharge.” Ground improvement—Case histories, B. Indraratna and J. Chu, eds., Elsevier, Amsterdam, 199–229.
Kim, D. S., Cho, G. C., Kim, N. R., and Choo, Y. W. (2007). “Development of KOCED geotechnical centrifuge facility.” Proc., 13th Asian Regional Conf.
Rowe, R. K., and Li, A. L. (2005). “Geosynthetic-reinforced embankments over soft foundations.” Geosynth. Int., 12(1), 50–85.
Sathananthan, I., and Indraratna, B. (2006). “Laboratory evaluation of smear zone and correlation between permeability and moisture content.” J. Geotech. Geoenviron. Eng., 132(7), 942–945.
Sharma, J. S., and Xiao, D. (2000). “Characterization of a smear zone around vertical drains by large-scale laboratory tests.” Can. Geotech. J., 37(6), 1265–1271.
Shin, D. H., Lee, C., Lee, J. S., and Lee, W. (2009). “Detection of smear zone using micro-cone and electrical resistance.” Can. Geotech. J., 46(6), 719–726.
White, D. J., Take, W. A., and Bolton, D. (2003). “Soil deformation measurement using particle image velocimetry and photogrammetry.” Geotechnique, 53(7), 619–631.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Aug 26, 2011
Accepted: Jun 20, 2012
Published online: Aug 1, 2012
Published in print: Jun 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.