Centrifuge and Numerical Modeling of Normal Fault-Rupture Propagation in Clay with and without a Preexisting Fracture
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 138, Issue 12
Abstract
Over the last few decades, extensive research has been conducted to investigate fault-rupture propagation induced by faulting through uncemented soil. While it has long been realized that many natural soils are cemented, relatively few publications have been devoted to investigating fault-rupture propagation in cemented soil. Moreover, preexisting fracture in soil may be reactivated during earthquakes, and its influence on fault-rupture propagation is not fully understood. In this study, three centrifuge model tests are reported on investigating fault-rupture propagation induced by normal faulting in uncemented clay and cemented clay with and without a preexisting fracture. Preliminary numerical analyses of the centrifuge tests are also carried out to study the mechanism of fault-rupture propagation in these three ground conditions. Ground deformation was dominated by a shear mechanism in uncemented clay, and a shear zone along the projection of the bedrock-fault plane was observed. On the other hand, a bending deformation mechanism was identified at the ground surface in cemented clay with and without a preexisting fracture. In the presence of cementation, two main ruptures were observed, where one initiated at the cemented ground surface and propagated downward toward the center of the cemented clay, whereas the other initiated at the bedrock fault and propagated upward. The presence of a fracture in cemented clay was found to initiate a fault rupture at the tip of the preexisting fracture.
Get full access to this article
View all available purchase options and get full access to this article.
References
Anastasopoulos, I., Gazetas, G., Bransby, M. F., Davies, M. C. R., and El Nahas, A. (2007). “Fault rupture propagation through sand: Finite-element analysis and validation through centrifuge experiments.” J. Geotech. Geoenviron. Eng., 133(8), 943–958.
Bray, J. D., Seed, R. B., Cluff, L. S., and Seed, H. B. (1994a). “Earthquake fault rupture propagation through soil.” J. Geotech. Eng., 120(3), 543–561.
Bray, J. D., Seed, R. B., and Seed, H. B. (1993). “1 g small-scale modelling of saturated cohesive soils.” Geotech. Test. J., 16(1), 46–53.
Bray, J. D., Seed, R. B., and Seed, H. B. (1994b). “Analysis of earthquake fault rupture propagation through cohesive soil.” J. Geotech. Eng., 120(3), 562–580.
Cai, Q. P., Hu, P., Van Laak, P., Ng, C. W. W., and Chiu, A. C. F. (2010). “Investigation of boundary conditions for simulating normal fault propagation in centrifuge.” Proc., 4th Int. Conf. on Geotechnical Engineering and Soil Mechanics, Iranian Geotechnical Society, Tehran, Iran, 614.
Cole, D. A., Jr., and Lade, P. V. (1984). “Influence zones in alluvium over dip-slip faults.” J. Geotech. Eng., 110(5), 599–615.
Dong, J. J., Wang, C. D., Lee, C. T., Liao, J. J., and Pan, Y. W. (2004). “The influence of surface ruptures on building damage in the 1999 Chi-Chi earthquake: A case study in Fengyuan City.” Eng. Geol., 71(1–2), 157–179.
Faccioli, E., Anastasopoulos, I., Gazetas, G., Callerio, A., and Paolucci, R. (2008). “Fault rupture-foundation interaction: Selected case histories.” Bull. Earthquake Eng., 6(4), 557–583.
FLAC: Fast Lagrangian Analysis of Continua [Computer software]. Minneapolis, Itasca Consulting Group.
Head, K. H. (1982). Manual of soil laboratory testing, Pentech Press, London.
Hu, P., Cai, Q. P., Luo, G. Y., Ding, Y. H., Ng, C. W. W., and Hou, Y. J. (2010). “Centrifuge modeling of the influence of pre-existing fractures in multilayered soils on ground deformations.” Proc., 5th Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics, Univ. of Missouri-Rolla, Rolla, MO, 1.16b.
Huang, T., and Airey, D. W. (1998). “Properties of artificially cemented carbonate sand.” J. Geotech. Geoenviron. Eng., 124(6), 492–499.
Lade, P. V., Cole, D. A., Jr., and Cummings, D. (1984). “Multiple failure surfaces over dip-slip faults.” J. Geotech. Eng., 110(5), 616–627.
Lin, M. L., Chung, C. F., and Jeng, F. S. (2006). “Deformation of overburden soil induced by thrust fault slip.” Eng. Geol., 88(1–2), 70–89.
Ng, C. W. W., Li, X. S., Van Laak, P. A., and Hou, D. Y. J. (2004). “Centrifuge modeling of loose fill embankment subjected to uni-axial and bi-axial earthquakes.” Soil. Dyn. Earthquake Eng., 24(4), 305–318.
Powrie, W. (1997). Soil mechanics: Concepts and applications, E & FN Spon, London.
Roth, W. H., Scott, R. F., and Austin, I. (1981). “Centrifuge modeling of fault propagation through alluvial soils.” Geophys. Res. Lett., 8(6), 561–564.
Sherard, J. L., Cluff, L. S., and Allen, C. R. (1974). “Potentially active faults in dam foundations.” Geotechnique, 24(3), 367–428.
Shi, L. Y. (2004). “Influence of artificial weak cementation on loose silty sand behavior.” M.Phil. thesis, Hong Kong Univ. of Science and Technology, Hong Kong.
Stone, K. J. L., and Wood, D. M. (1992). “Effects of dilatancy and particle size observed in model tests on sand.” Soil Found., 32(4), 43–57.
Wells, D. L., and Coppersmith, K. J. (1994). “New empirical relationships among magnitude, rupture length, rupture width, rupture area, and surface displacement.” Bull. Seismol. Soc. Am., 84(4), 974–1002.
White, D. J., Take, W. A., and Bolton, M. D. (2003). “Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry.” Geotechnique, 53(7), 619–631.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 138 • Issue 12 • December 2012
Pages: 1492 - 1502
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Mar 18, 2011
Accepted: Feb 27, 2012
Published online: Nov 14, 2012
Published in print: Dec 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.