Improved Performance of Railway Ballast under Impact Loads Using Shock Mats
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 138, Issue 3
Abstract
Impact loads generated because of wheel and rail defects cause accelerated ballast breakage leading to adverse performance of ballasted rail tracks. In the present study, experimental and numerical investigations have been carried out to develop an understanding of the performance of shock mats in the attenuation of dynamic impact loads and subsequent mitigation of ballast degradation. The investigations include different locations of shock mats considering stiff and weak subgrade conditions. With the provision of shock mats, the magnitude of impact forces decreases, and the time duration of impact ges prolonged. In the case of stiff subgrade, the efficiency of the shock mat in reducing the impact forces is greater when it is located at the bottom of ballast rather than at the top, whereas the reverse is true for weak subgrade. However, the provision of shock mats both at the top and bottom of the ballast bed, irrespective of the subgrade condition, is the best solution for minimising the impact force. The shock mats can bring down the impact-induced strains in the ballast bed by as much as 50%, apart from substantially reducing the ballast breakage.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to thank the CRC for Rail Innovation (Australia) for its financial support. The contributions made by Sandy Pfeiffer and Dr. Sak Kaewunruen (RailCorp, Sydney) and Tim Neville (Australian Rail Track Corporation, Newcastle) during the field studies are gratefully appreciated. The assistance provided by senior technical officers, Alan Grant, Ian Bridge, and Cameron Neilson is also appreciated. The authors also express their appreciation to Dr. Cholachat Rujikiatkamjorn, Senior Lecturer, University of Wollongong (Australia) for the valuable comments.
References
Amorosi, A., Boldini, D., and Elia, G. (2010). “Parametric study on seismic ground response by finite element modeling.” Comput. Geotech., 37(4), 515–528.
Anastasopoulos, I., Alfi, S., Gazetas, G., Bruni, S., and Leuven, A. V. (2009). “Numerical and experimental assessment of advanced concepts to reduce noise and vibration on urban rassessmentailway turnouts.” J. Transp. Eng., 135(5), 279–287.
Auersch, L. (2006). “Dynamic axle loads on tracks with and without ballast mats: numerical results of three-dimensional vehicle-track-soil models.” Proc., Inst. Mech. Eng. Part F, 220(2), 169–183.
Bishop, A. W., and Henkel, D. J. (1957). The measurement of soil properties in the triaxial test, 2nd Ed., Edward Arnold, London.
Bona, M. E. (2004). “The effect of straightening and grinding of welds on track roughness.” M.S. thesis, Queensland Univ. of Technology, Australia.
British Rail Safety and Standards Board. (1995). “Commentary on permissible track forces for railway vehicles: Issue 1.” GM/RC2513, Rail Safety and Standards Board, London.
Brown, S. F., Kwan, J., and Thom, N. H. (2007). “Identifying the key parameters that influence geogrid reinforcement of railway ballast.” Geotext. Geomembr., 25(6), 326–335.
Bruni, S., Anastasopoulos, I., Alfi, S., Leuven, V. A., Apostolic, M., and Gazetas, G. (2009). “Train-induced vibrations on urban metro and tram turnouts.” J. Transp. Eng.,135(7), 397–405.
Chopra, A. K. (2007). Dynamics of structures: Theory and applications to earthquake engineering, Pearson Prentice Hall, Upper Saddle River, NJ.
Clough, R. W., and Penzien, J. (2003). Dynamics of structures, 2nd Ed., McGraw-Hill, New York.
Esveld, C. (2001). Modern railway track, MRT-Productions, Netherlands.
Frederick, C. O., and Round, D. J. (1985). "Vertical track loading", Track technology, Thomas Telford, London, 135-149.
Henkel, D. J., and Gilbert, G. D. (1952). “The effect of the rubber membrane on the measured triaxial compression strength of clay samples.” Geotechnique, 3(1), 20–29.
Hilber, H. M., Hughes, T. J. R., and Taylor, R. L. (1977). “Improved numerical dissipation for time integration algorithms in structural dynamics.” Earthquake Eng. Struct. Dyn., 5(3), 283–292.
Hossain, Z., Indraratna, B., Darve, F., and Thakur, P. (2007). “DEM analysis of angular ballast breakage under cyclic loading.” Geomech. Geoeng., 2(3), 175–181.
Indraratna, B., Ionescu, D., and Christie, H. D. (1998). “Shear behaviour of railway ballast based on large scale traiaxial testing.” J. Geotech. Geoenviron. Eng.,124(5), 439–449.
Indraratna, B., Lackenby, J., and Christie, D. (2005). “Effect of confining pressure on the gradation of ballast under cyclic loading.” Geotechnique, 55(4), 325–328.
Indraratna, B., Nimbalkar, S., Christie, D., Rujikiatkamjorn, C., and Vinod, J. S. (2010). “Field assessment of the performance of a ballasted rail track with and without geosynthetics.” J. Geotech. Geoenviron. Eng., 136(7), 907–917.
Indraratna, B., and Salim, W. (2002). “Modelling of particle breakage of course aggregates incorporating strength and dilatancy.” Proc. Inst. Civ. Eng. Geotech. Eng. 155(4), 243–252.
Indraratna, B., and Salim, W. (2003). “Deformation and degradation mechanics of recycled ballast stabilised with geosynthetics.” Soils Found., 43(4), 35–46.
Indraratna, B., Salim, W., and Rujikiatkamjorn, C. (2011). Advanced rail geotechnology—ballasted track, CRC Press, London.
Indraratna, B., Shahin, M. A., and Salim, W. (2007). “Stabilising granular media and formation soil using geosynthetics with special reference to Railway engineering.” Ground Improv., 11(1), 27–44.
Jenkins, H. M., Stephenson, J. E., Clayton, G. A., Moorland, J. W., and Lyon, D. (1974). “The effect of track and vehicle parameters on wheel/rail vertical dynamic forces.” Railway Engineering Journal, 3(1), 2–16.
Kaewunruen, S., and Remennikov, A. (2010). “Dynamic crack propagations in prestressed concrete sleepers in railway track systems subjected to severe impact loads.” J. Struct. Eng., 136(6), 749–754.
Kramer, S. L. (1996). Geotechnical earthquake engineering, Prentice Hall, Trenton, NJ.
Lackenby, J., Indraratna, B., McDowell, G., and Christie, D. (2007). “Effect of confining pressure on ballast degradation and deformation under cyclic triaxial loading.” Geotechnique, 57(6), 527–536.
Li, D., and Davis, D. (2005). “Transition of railroad bridge approaches.” J. Geotech. Geoenviron. Eng., 131(11), 1392–1398.
Marsal, R. J. (1973). “Mechanical properties of rock fill.” Embankment dam engineering: Casagrande volume, R. C. Hirschfield and S. J. Pools, eds., Wiley, New York, 109–200.
Meyers, M. A. (1994). Dynamic behaviour of materials, Wiley, New York.
Newmark, N. M. (1959). “A method of computation for structural dynamics.” J. Engrg. Mech. Div., 85(3), 67–94.
Nielsen, J. C. O., and Johansson, A. (2000). “Out of round railway wheels—a literature survey.” Proc., Inst. Mech. Eng. Part F, 214(2), 79–91.
PLAXIS 2D Version 8.6—Finite element code for soil and rock analysis Dynamic package [Computer software]. Delft, Netherlands, PLAXIS BV.
Rochard, B. P., and Schmidt, F. (2004). “Benefits of lower-mass trains for high speed rail operations.” Proc. Inst. Civ. Eng. Transp., 157(1), 51–64.
Rowe, P. W. (1962). “The stress-dilatancy relation for the static equilibrium of an assembly of particles in contact.” Proc. R. Soc. London, Ser. A, 269(1339), 500–527.
Salim, W., and Indraratna, B. (2004). “A new elastic-plastic constitutive model for coarse granular aggregates incorporating particle breakage.” Can. Geotech. J., 41(4), 657–671.
Saxton, H. J., Ireland, D. R., and Server, W. L. (1974). “Analysis and control of inertial effects during instrumented impact testing.” ASTM Spec. Tech. Publ., American Society of Testing and Materials, Philadelphia, 50–73.
Schanz, T., Vermeer, P. A., and Bonnier, P. G. (1999). “The hardening soil model—Formulation and verification.” Proc. Plaxis Symp. ‘Beyond 2000 in Computational Geotechnics." Amsterdam Balkema, Rotterdam, 55–58.
Selig, E. T., and Waters, J. M. (1994). Track geotechnology and substructure management, Thomas Telford Services, London.
Sluys, L. J. (1992). “Wave propagation, localization and dispersion in softening solids.” Ph.D. thesis, Delft Univ. of Technology, Netherlands.
Standards Australia. (1996). Aggregates and rock for engineering purposes, Part 7: Railway ballast, AS 2758.7-1996, NSW, Sydney, Australia.
Steffens, D., and Murray, M. (2005). “Establishing meaningful results from models of railway track dynamic behaviour.” Proc., 8th Int. Heavy Haul Conf., C. Jorge, ed., Rio de Janeiro, Brazil, 41–50.
Suiker, A. S. J., Selig, E. T., and Frenkel, R. (2005). “Static and cyclic triaxial testing of ballast and subballast.” J. Geotech. Geoenviron. Engng., 131(6), 771–782.
Timoshenko, S. P., and Goodier, J. N. (1970). Theory of elasticity, McGraw Hill, New York.
Tutumluer, E., and Kim, M. (2007). “Considerations for nonlinear analyses of pavement foundation geomaterials in the finite element modeling of flexible pavements.” Analysis of Asphalt Pavement Materials and Systems: Engineering Methods (ASCE GSP 176), L. Wang and E. Masad, eds., ASCE, Reston, VA.
Tutumluer, E., and Pan, T. (2008). “Aggregate morphology affecting strength and permanent deformation behavior of unbound aggregate materials.” J. Mater. Civ. Eng.,, 20(9), 617–627.
Ueng, T. S., and Chen, T. J. (2000). “Energy aspects of particle breakage in drained shear of sands.” Geotechnique, 50(1), 65–72.
Verruijt, A., Brinkgreve, R. B. J., and Li, S. (2008). “Analytical and numerical solution of the elastodynamic strip load problem.” Int. J. Numer. Anal. Methods Geomech., 32(1), 65–80.
Woodward, P. K., and Griffiths, D. V. (1996). “Influence of viscous damping in the dynamic analysis of an earth dam using simple constitutive models.” Comput. Geotech., 19(3), 245–263.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Aug 25, 2010
Accepted: Jul 8, 2011
Published online: Feb 15, 2012
Published in print: Mar 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.