Keying of Rectangular Plate Anchors in Normally Consolidated Clays
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 137, Issue 12
Abstract
The loss in anchor embedment during keying, as it rotates to become normal to the cable load, reduces the uplift capacity of anchors in normally consolidated clay. The keying behavior of plate anchors has been studied previously by using centrifuge and field model tests. In this paper, a large deformation finite-element approach incorporating frequent mesh regeneration and allowing for evolution of the anchor-chain profile, was developed to simulate the keying process of rectangular and strip plate anchors. A parametric study was undertaken to quantify the loss in anchor embedment during keying in terms of the anchor geometry, soil properties, loading eccentricity, and inclination. The embedment loss decreased dramatically with increasing loading eccentricity and decreasing chain angle at the mudline to the horizontal. The loss in anchor embedment during keying increased as the local soil strength increased relative to the weight of the anchor, up to a limit determined by the eccentricity of loading. In contrast, the effect of the soil strength gradient was minimal. Findings of this study yield a recommendation that the most important factor in anchor keying, loading eccentricity, should not be less than half the anchor width for an effective design.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work described in this paper was supported by the Australian Research Council through the Discovery Project Scheme (UNSPECIFIEDDP 0344019) and contributes to the research program of the Centre for Offshore Foundation Systems supported by the State Government of Western Australia through the Centre of Excellence in Science and Innovation program. This support is gratefully acknowledged.
References
ABAQUS Version 6.5. [Computer software]. (2004). Hibbitt, Karlsson, and Sorensen, Providence, RI.
Aubeny, C. P., Murff, D. J., and Roesset, J. M. (2001). “Geotechnical issues in deep and ultra deep waters.” Proc., 10th Int. Conf. Computer Methods and Advances in Geomechanics, Tucson, AZ, 13–26.
Boroomand, B., and Zienkiewicz, O. C. (1997). “An improved REP recovery and the effectivity robustness test.” Int. J. Numer. Methods Eng., 40(17), 3247–3277.
Dove, P., Treu, H., and Wilde, B. (1998). “Suction embedded plate anchor (SEPLA): a new anchoring solution for ultra-deepwater mooring.” Proc., DOT Conf., New Orleans.
Gaudin, C., O’Loughlin, C. D., Randolph, M. F., and Lowmass, A. C. (2006). “Influence of the installation process on the performance of suction embedded plate anchors.” Géotechnique, 56(6), 381–391.
Gaudin, C., Tham, K. H., and Ouahsine, S. (2008). “Plate anchor failure mechanism during keying process.” Proc., 18th Int. Offshore and Polar Eng. Conf., Vol. 2, Int. Society of Offshore and Polar Engineers (ISOPE), Cupertino, CA, 613–619.
Gill, D. R., and Lehan, B. M. (2001). “An optical technique for investigating soil displacement patterns.” Geotech. Test. J., 24(3), 324–329.
Hossain, M. S., and Randolph, M. F. (2009). “Effect of strain rate and strain softening on the penetration resistance of spudcan foundations on clay.” Int. J. Geomech., 9(3), 122–132.
Hu, Y., and Randolph, M. F. (1998). “A practical numerical approach for large deformation problems in soil.” Int. J. Numer. Anal. Methods Geomech., 22(5), 327–350.
Neubecker, S. R., and Randolph, M. F. (1995). “Profile and frictional capacity of embedded anchor chains.” J. Geotech. Eng., 121(11), 797–803.
O’Loughlin, C. D., Lowmass, A. C., Gaudin, C., and Randolph, M. F. (2006). “Physical modelling to assess keying characteristics of plate anchors.” Proc., 6th Int. Conf. Physical Modelling in Geotechnics, Hong Kong, 659–665.
O’Neill, M. P., Bransby, M. F., and Randolph, M. F. (2003). “Drag anchor fluke-soil interaction in clay.” Can. Geotech. J., 40(1), 78–94.
Randolph, M. F., Cassidy, M. J., Gourvenec, S., and Erbrich, C. (2005). “Challenges of offshore geotechnical engineering.” Proc., 16th Int. Conf. Soil Mech. Geotech. Eng., Osaka, Japan, 123–176.
Randolph, M. F., Wang, D., Zhou, H., Hossain, M. S., and Hu, Y. (2008). “Large deformation finite element analysis for offshore applications.” Proc., 12th Int. Conf. of the Int. Association for Computer Methods and Advances in Geomechanics, Goa, India, 3307–3318.
Song, Z., Hu, Y., O’Loughlin, C., and Randolph, M. F. (2009). “Loss in anchor embedment during plate anchor keying in clay.” J. Geotech. Geoenviron. Eng., 135(10), 1475–1485.
Song, Z., Hu, Y., and Randolph, M. F. (2008). “Numerical simulation of vertical pullout of plate anchors in clay.” J. Geotech. Geoenviron. Eng., 134(6), 866–875.
Song, Z., Hu, Y., Wang, D., and O’Loughlin, C. D. (2006). “Pullout capacity and rotational behavior of square anchors.” Proc., 6th Int. Conf. Physical Modelling in Geotechnics, Hong Kong, 1325–1331.
Wang, D., Hu, Y., and Randolph, M. F. (2008). “Effect of loading rate on the uplift capacity of plate anchors.” Proc., 18th Int. Offshore and Polar Eng. Conf., Vol. 2, ISOPE, Cupertino, CA, 727–731.
Wang, D., Hu, Y., and Randolph, M. F. (2010a). “Three-dimensional large deformation analysis of plate anchors in uniform clay.” J. Geotech. Geoenviron. Eng., 136(2), 355–365.
Wang, D., Hu, Y., and Jin, X. (2006). “Two-dimensional large deformation finite element analysis for pulling-up of plate anchor.” China Ocean Eng., 20(2), 269–279.
Wang, D., White, D. J., and Randolph, M. F. (2010b). “Large-deformation finite element analysis of pipe penetration and large-amplitude lateral displacement.” Can. Geotech. J., 47(8), 842–856.
White, D. J., Take, W. A., and Bolton, M. D. (2003). “Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry.” Géotechnique, 53(7), 619–631.
Wilde, B., Treu, H., and Fulton, T. (2001). “Field testing of suction embedded plate anchors.” Proc., 11th Int. Offshore and Polar Eng. Conf., ISOPE, Cupertino, CA, 544–551.
Zienkiewicz, O. C., and Zhu, J. Z. (1992). “The superconvergent patch recovery and a posterior error estimates. Part 1: The recovery technique.” Int. J. Numer. Methods Eng., 33(7), 1331–1364.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Sep 8, 2009
Accepted: Nov 1, 2010
Published online: Nov 4, 2010
Published in print: Dec 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.