Intramethod Variability in ReMi Dispersion Measurements and Estimates at Shallow Bedrock Sites
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 137, Issue 4
Abstract
The refraction microtremor (ReMi) method uses a linear array of receivers to record passive noise stress waves, thereby negating the need for a strong active source such as those typically employed in other linear-array surface-wave methods. The simplicity of such an approach is very appealing; however, there is a potential for significant uncertainty in shear-wave velocity () estimates obtained in this manner because much is unknown about the seismic wavefield that is being sampled. This article examines intramethod variability in ReMi dispersion measurements and estimates at shallow bedrock sites. The focus is not on evaluating whether ReMi measurements yielded the “true” profiles for the study sites, but rather on evaluating how the dispersion curves and profiles at the sites were affected by variations in the seismic wavefield sampled by a linear array of receivers. It was found that changes in the sampled seismic wavefield, obtained through employing various array orientations at a site and inclusion of actively generated noise, resulted in significant variations in the ReMi-obtained dispersion curves and profiles at the study sites, thus yielding a high level of intramethod variability for a given test location.
Get full access to this article
View all available purchase options and get full access to this article.
References
Aki, K. (1957). “Space and time spectra of stationary stochastic waves, with special reference to microtremors.” Bull. Earthquake Res. Inst., 35, 415–457.
Anderson, N., Thitimakorn, T., Ismail, A., and Hoffman, D. (2007). “A comparison of four geophysical methods for determining the shear wave velocity of soils.” Environ. Eng. Geosci., 13(1), 11–23.
Beekman, A. N. (2008). “A comparison of experimental ReMi measurements with various source, array, and site conditions.” M.S. thesis, Univ. of Arkansas, Fayetteville, AR.
Di Giulio, G., Cornou, C., Ohrnberger, M., Wathelet, M., and Rovelli, A. (2006). “Deriving wavefield characteristics and shear-velocity profiles from two-dimensionsal small aperture arrays analysis of ambient vibrations in a small-size alluvial basin, Colfiorito, Italy.” Bull. Seismol. Soc. Am., 96(5), 1915–1933.
Endrun, B., Ohrnberger, M., and Sawaidis, A. (2010). “On the repeatability and consistency of three-component ambient vibration array measurements.” Bull. Earthquake Eng., 8(3), 535–570.
Louie, J. N. (2001a). “Faster, better: Shear wave velocity to 100 meters depth from refraction microtremor arrays.” Bull. Seismol. Soc. Am., 91(2), 347–364.
Louie, J. N. (2001b). “Refraction microtremor (ReMi) refraction field tutorial: 30-meter shear velocity with two hours effort.” 〈http://www.seismo.unr.edu/remi/field-tutorial.html〉 (May 2009).
Optim. (2006). User’s manual: SeisOpt ReMi version 4.0, Optim, Inc., Reno, NV, 85.
Pancha, A., Anderson, J. G., Louie, J. N., and Pullammanappallil, S. K. (2008). “Measurement of shallow shear wave velocities at a rock site using the ReMi technique.” Soil Dyn. Earthquake Eng., 28(7), 522–535.
Pullammanappallil, S., Honjas, W., and Louie, J. N. (2003). “Determination of 1-D shear wave velocities using the refraction microtremor method.” Proc. 3rd Int. Conf. on the Application of Geophysical Methodologies and NDT to Transportation and Infrastructure, Federal Highway Administration, Washington, DC.
Rosenblad, B. L., and Li, J. (2009). “Comparative study of refraction microtremor (ReMi) and active source methods for developing low-frequency surface wave dispersion curves.” J. Environ. Eng. Geophys., 14(3), 101–113.
Tokimatsu, K. (1995). “Geotechnical site characterization using surface waves.” Proc. 1st Int. Conf. on Earthquake Geotechnical Engineering, Balkema, Brookfield, VA, 1333–1368.
Tokimatsu, K., Shinzawa, K., and Kuwayama, S. (1992). “Use of short-period microtremors for profiling.” J. Geotech. Eng., 118(10), 1544–1558.
Yoon, S., and Rix, G. (2009). “Near-field effects on array-based surface wave methods with active sources.” J. Geotech. Geoenviron. Eng., 135(3), 399–406.
Zywicki, D. J. (1999). “Advanced signal processing methods applied to engineering analysis of seismic surface waves.” Ph.D. dissertation, Georgia Institute of Technology, Atlanta.
Zywicki, D. J. (2007). “The impact of seismic wavefield and source properties on ReMi estimates.” Proc. Geo-Denver, ASCE, Reston, VA.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Dec 30, 2009
Accepted: Aug 10, 2010
Published online: Sep 2, 2010
Published in print: Apr 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.