Three-Dimensional Discrete-Element-Method Analysis of Behavior of Geogrid-Reinforced Sand Foundations under Strip Footing
Publication: International Journal of Geomechanics
Volume 22, Issue 9
Abstract
This paper presents a three-dimensional discrete numerical analysis associated with the interaction of geogrid and surrounding soils in geogrid-reinforced sand foundations under strip footing. After validating the numerical simulations with experimental results, the model was then employed to examine the deformation behaviors, contact force network, energy dissipation mechanism, and response of the geogrid. Additional analysis was also carried out to understand the effect of geogrid layout parameters on the bearing capacity of foundations and progressive failure of reinforcements. The results showed that the inclusion of geogrid layers spaced at 0.25B (B = footing width) inhibits the horizontal displacement of soils in the reinforced zone, whereas facilitates the displacement field in the underlying unreinforced zone and consequently results in an upward tensile failure of reinforcements. The progressive failure of reinforcements induces fluctuations of the loading–displacement curve in the postpeak regime. Punching shear failure initially develops in the reinforced zone in terms of force chains developing directly beneath the footing. With footing settlement increasing, the failure mode is characterized by a punching failure with a diffusion angle developing in the reinforced zone, followed by a general shear failure in the underlying unreinforced zone. Furthermore, the progressive failure of geogrid layers is associated with reinforcement spacing and number of reinforcement layers, rather than reinforcement length. A larger reinforcement spacing and a higher number of reinforcement layers tend to induce a downward fracture failure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the National Natural Science Foundation of China under Grant No. 41772289.
References
Abu-Farsakh, M., Q. Chen, and R. Sharma. 2013. “An experimental evaluation of the behavior of footings on geosynthetic-reinforced sand.” Soils Found. 53 (2): 335–348. https://doi.org/10.1016/j.sandf.2013.01.001.
Adams, M. T., and J. G. Collin. 1997. “Large model spread footing load tests on geosynthetic reinforced soil foundations.” J. Geotech. Geoenviron. Eng. 123 (1): 66–72. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:1(66).
Ai, J., J. F. Chen, J. M. Rotter, and Y. O. Jin. 2011. “Assessment of rolling resistance models in discrete element simulations.” Powder Technol. 206 (3): 269–282. https://doi.org/10.1016/j.powtec.2010.09.030.
ASTM. 2015. Standard test method for determining tensile properties of geogrids by the single or multi-rib tensile method. D6637/D6637M–15. West Conshohocken, PA: ASTM.
Badakhshan, E., A. Noorzad, A. Bouazza, S. Zameni, and L. King. 2020. “A 3D-DEM investigation of the mechanism of arching within geosynthetic-reinforced piled embankment.” Int. J. Solids Struct. 187: 58–74. https://doi.org/10.1016/j.ijsolstr.2019.03.035.
Bathurst, R. J., and L. Rothenburg. 1992. “Investigation of micromechanical features of idealized granular assemblies using DEM.” Eng. Comput. 9 (2): 199–210. https://doi.org/10.1108/eb023859.
Bhandari, A., J. Han, and R. L. Parsons. 2015. “Two-dimensional DEM analysis of behavior of geogrid-reinforced uniform granular bases under a vertical cyclic load.” Acta Geotech. 10 (4): 469–480. https://doi.org/10.1007/s11440-013-0299-3.
Binquet, J., and K. L. Lee. 1975a. “Bearing capacity tests on reinforced earth slabs.” J. Geotech. Eng. Div. 101 (12): 1241–1255. https://doi.org/10.1061/AJGEB6.0000219.
Binquet, J., and K. L. Lee. 1975b. “Bearing capacity analysis of reinforced earth slabs.” J. Geotech. Eng. Div. 101 (12): 1257–1276. https://doi.org/10.1061/AJGEB6.0000220.
Chakraborty, D., and J. Kumar. 2015. “Bearing capacity of circular footings on reinforced soils.” Int. J. Geomech. 15 (1): 04014034. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000343.
Chen, J., X. Guo, R. Sun, S. Rajesh, S. Jiang, and J. Xue. 2021. “Physical and numerical modeling of strip footing on geogrid reinforced transparent sand.” Geotext. Geomembr. 49 (2): 399–412. https://doi.org/10.1016/j.geotexmem.2020.10.011.
Chen, J. F., X. P. Guo, J. F. Xue, and P. H. Guo. 2019. “Load behaviour of model strip footings on reinforced transparent soils.” Geosynth. Int. 26 (3): 251–260. https://doi.org/10.1680/jgein.19.00003.
Chen, J. F., A. Tolooiyan, J. F. Xue, and Z. M. Shi. 2016. “Performance of a geogrid reinforced soil wall on PVD drained multilayer soft soils.” Geotext. Geomembr. 44 (3): 219–229. https://doi.org/10.1016/j.geotexmem.2015.10.001.
Chen, Q. M., and M. Abu-Farsakh. 2015. “Ultimate bearing capacity analysis of strip footings on reinforced soil foundation.” Soils Found. 55 (1): 74–85. https://doi.org/10.1016/j.sandf.2014.12.006.
Chen, Q. M., M. Abu-Farsakh, and R. Sharma. 2009. “Experimental and analytical studies of reinforced crushed limestone.” Geotext. Geomembr. 27 (5): 357–367. https://doi.org/10.1016/j.geotexmem.2009.03.002.
Chen, R. P., Q. W. Liu, H. N. Wu, H. L. Wang, and F. Y. Meng. 2020. “Effect of particle shape on the development of 2D soil arching.” Comput. Geotech. 125: 103662. https://doi.org/10.1016/j.compgeo.2020.103662.
Cundall, P. A., and O. D. L. Strack. 1979. “A discrete numerical model for granular assemblies.” Géotechnique 29 (1): 47–65. https://doi.org/10.1680/geot.1980.30.3.331.
Daniel, D. E., R. M. Koerner, R. Bonaparte, R. E. Landreth, D. A. Carson, and H. B. Scranton. 1998. “Slope stability of geosynthetic clay liner test plots.” J. Geotech. Geoenviron. Eng. 124 (7): 628–637. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:7(628).
Dash, S. K., K. Rajagopal, and N. R. Krishnaswamy. 2004. “Performance of different geosynthetic reinforcement materials in sand foundations.” Geosynth. Int. 11 (1): 35–42. https://doi.org/10.1680/gein.2004.11.1.35.
Demir, A., M. Laman, A. Yildiz, and M. Ornek. 2013. “Large scale field tests on geogrid-reinforced granular fill underlain by clay soil.” Geotext. Geomembr. 38: 1–15. https://doi.org/10.1016/j.geotexmem.2012.05.007.
Ehrlich, M., and J. K. Mitchell. 1994. “Working stress design method for reinforced soil walls.” J. Geotech. Eng. 120 (4): 625–645. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:4(625).
Gao, G., and M. A. Meguid. 2018. “Effect of particle shape on the response of geogrid-reinforced systems: Insights from 3D discrete element analysis.” Geotext. Geomembr. 46 (6): 685–698. https://doi.org/10.1016/j.geotexmem.2018.07.001.
Gu, M., J. Han, and M. Zhao. 2017. “Three-dimensional discrete-element method analysis of stresses and deformations of a single geogrid-encased stone column.” Int. J. Geomech. 17 (9): 04017070. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000952.
Guido, V. A., D. K. Chang, and M. A. Sweeny. 1986. “Comparison of geogrid and geotextile reinforced slabs.” Can. Geotech. J. 23 (4): 435–440. https://doi.org/10.1016/0148-9062(87)91106-5.
Han, J., A. Bhandari, and F. Wang. 2012. “DEM analysis of stresses and deformations of geogrid-reinforced embankments over piles.” Int. J. Geomech. 12 (4): 340–350. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000050.
Han, J., and M. A. Gabr. 2002. “Numerical analysis of geosynthetic-reinforced and pile-supported earth platforms over soft soil.” J. Geotech. Geoenviron. Eng. 128 (1): 44–53. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:1(44).
Huang, C. C., and F. Y. Menq. 1997. “Deep-footing and wide-slab effects in reinforced sandy ground.” J. Geotech. Geoenviron. Eng. 123 (1): 30–36. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:1(30).
Huang, C. C., and F. Tatsuoka. 1990. “Bearing capacity of reinforced horizontal sandy ground.” Geotext. Geomembr. 9 (1): 51–82. https://doi.org/10.1016/0266-1144(90)90005-W.
Hussein, M. G., and M. A. Meguid. 2016. “A three-dimensional finite element approach for modeling biaxial geogrid with application to geogrid-reinforced soils.” Geotext. Geomembr. 44 (3): 295–307. https://doi.org/10.1016/j.geotexmem.2015.12.004.
Itasca. 2018. Particle Flow Code, version 5.0 documentation. Minneapolis: Itasca Consulting Group.
Lai, H. J., J. J. Zheng, J. Zhang, R. J. Zhang, and C. Lan. 2014. “DEM analysis of “soil”-arching within geogrid-reinforced and unreinforced pile-supported embankments.” Comput. Geotech. 61: 13–23. https://doi.org/10.1016/j.compgeo.2014.04.007.
Lai, J., and B. H. Yang. 2017. “Laboratory testing and numerical simulation of a strip footing on geosynthetically reinforced loose sand.” J. Test. Eval. 45 (1): 51–60.
Laman, M., and A. Yildiz. 2007. “Numerical studies of ring foundations on geogrid-reinforced sand.” Geosynth. Int. 14 (2): 52–64. https://doi.org/10.1680/gein.2007.14.2.52.
Latha, G. M., and A. Somwanshi. 2009. “Bearing capacity of square footings on geosynthetic reinforced sand.” Geotext. Geomembr. 27 (4): 281–294. https://doi.org/10.1016/j.geotexmem.2009.02.001.
Ling, X., H. Xiao, and X. Cui. 2018. “Analysis of mechanical properties of polyurethane-mixed ballast based on energy method.” Constr. Build. Mater. 182: 10–19. https://doi.org/10.1016/j.conbuildmat.2018.06.008.
Michalowski, R. L. 2004. “Limit loads on reinforced foundation soils.” J. Geotech. Geoenviron. Eng. 130 (4): 381–390. https://doi.org/10.1061/%E2%88%BCASCE!1090-0241%E2%88%BC2004!130:4%E2%88%BC381.
Michalowski, R. L., and L. Shi. 2003. “Deformation patterns of reinforced foundation sand at failure.” J. Geotech. Geoenviron. Eng. 129 (5): 439–449. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:6(439).
Naderi, E., and N. Hataf. 2014. “Model testing and numerical investigation of interference effect of closely spaced ring and circular footings on reinforced sand.” Geotext. Geomembr. 42 (3): 191–200. https://doi.org/10.1016/j.geotexmem.2013.12.010.
Ng, T. T. 2005. “Behavior of gravity deposited granular material under different stress paths.” Can. Geotech. J. 42 (6): 1644–1655. https://doi.org/10.1139/t05-080.
Omar, M. T., B. M. Das, V. K. Puri, and S. C. Yen. 1993. “Ultimate bearing capacity of shallow foundations on sand with geogrid reinforcement.” Can. Geotech. J. 30 (3): 545–549. https://doi.org/10.1139/t93-046.
O’Sullivan, C. 2011. “Particle-based discrete element modeling: Geomechanics perspective.” Int. J. Geomech. 11 (6): 449–464. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000024.
Ouria, A., and A. Mahmoudi. 2018. “Laboratory and numerical modeling of strip footing on geotextile-reinforced sand with cement-treated interface.” Geotext. Geomembr. 46 (1): 29–39. https://doi.org/10.1016/j.geotexmem.2017.09.003.
Prasad, B. D., C. Hariprasad, and B. Umashankar. 2016. “Load-settlement response of square footing on geogrid reinforced layered granular beds.” Int. J. Geosynth. Ground Eng. 2 (4): 36. https://doi.org/10.1007/s40891-016-0070-6.
Rothenburg, L., and R. J. Bathurst. 1989. “Analytical study of induced anisotropy in idealized granular materials.” Géotechnique 39 (4): 601–614. https://doi.org/10.1680/geot.1989.39.4.601.
Rothenburg, L., and R. J. Bathurst. 1992. “Micromechanical features of granular assemblies with planar elliptical particles.” Géotechnique 42 (1): 79–95. https://doi.org/10.1680/geot.1992.42.1.79.
Roy, S. S., and K. Deb. 2017a. “Bearing capacity of rectangular footings on multilayer geosynthetic-reinforced granular fill over soft soil.” Int. J. Geomech. 17 (9): 04017069. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000959.
Roy, S. S., and K. Deb. 2017b. “Effects of aspect ratio of footings on bearing capacity for geogrid-reinforced sand over soft soil.” Geosynth. Int. 24 (4): 362–382. https://doi.org/10.1680/jgein.17.00008.
Schlosser, F., H. M. Jacobsen, and I. Juran. 1983. “Soil reinforcement: General Report.” In Proc., 8th European Conf. on Soil Mechanics and Foundation Engineering, 83–103. Rotterdam, Netherlands: Balkema.
Sharma, R., Q. Chen, Q. Abu-Farsakh, and S. Yoon. 2009. “Analytical modeling of geogrid reinforced soil foundation.” Geotext. Geomembr. 27 (1): 63–72. https://doi.org/10.1016/j.geotexmem.2008.07.002.
Shin, E. C., B. M. Das, E. S. Lee, and C. Atalar. 2002. “Bearing capacity of strip foundation on geogrid-reinforced sand.” Geotech. Geol. Eng. 20 (2): 169–180. https://doi.org/10.1023/A:1015059427487.
Stone, K. J. L., and D. M. Wood. 1992. “Effects of dilatancy and particle size observed in model tests on sand.” Soils Found. 32 (4): 43–57. https://doi.org/10.3208/sandf1972.32.4_43.
Tafreshi, S., O. Khalaj, and M. Halvaee. 2011. “Experimental study of a shallow strip footing on geogrid-reinforced sand bed above a void.” Geosynth. Int. 18 (4): 178–195. https://doi.org/10.1680/gein.2011.18.4.178.
Tran, Q. A., P. Villard, and D. Dias. 2019. “Discrete and continuum numerical modeling of soil arching between piles.” Int. J. Geomech. 19 (2): 04018195. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001341.
Tran, V. D. H., M. A. Meguid, and L. E. Chouinard. 2015. “Three-dimensional analysis of geogrid-reinforced soil using a finite-discrete element framework.” Int. J. Geomech. 15 (4): 04014066. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000410.
Wang, J. Q., L. L. Zhang, J. F. Xue, and Y. Tang. 2018. “Load-settlement response of shallow square footings on geogrid-reinforced sand under cyclic loading.” Geotext. Geomembr. 46 (5): 586–596. https://doi.org/10.1016/j.geotexmem.2018.04.009.
Wang, Y. H., and S. C. Leung. 2008. “A particulate-scale investigation of cemented sand behavior.” Can. Geotech. J. 45 (1): 29–44. https://doi.org/10.1139/T07-070.
Wang, Z., F. Jacobs, and M. Ziegler. 2014. “Visualization of load transfer behaviour between geogrid and sand using PFC2D.” Geotext. Geomembr. 42 (2): 83–90. https://doi.org/10.1016/j.geotexmem.2014.01.001.
Wang, Z., F. Jacobs, M. Ziegler, and G. Yang. 2020. “Visualisation and quantification of geogrid reinforcing effects under strip footing loads using discrete element method.” Geotext. Geomembr. 48 (1): 62–70. https://doi.org/10.1016/j.geotexmem.2019.103505.
Wayne, M. H., J. Han, and K. Akins. 1998. “The design of geosynthetic reinforced foundations.” In Proc. ASCE's 1998 Annual Convention & Exposition. ASCE Geotechnical Special Publication. 1–18. Reston, VA: ASCE.
Wensrich, C. M., and A. Katterfeld. 2012. “Rolling friction as a technique for modeling particle shape in DEM.” Powder Technol. 217: 409–417. https://doi.org/10.1016/j.powtec.2011.10.057.
Xu, C., C. Liang, and P. Shen. 2019. “Experimental and theoretical studies on the ultimate bearing capacity of geogrid-reinforced sand.” Geotext. Geomembr. 47 (3): 417–428. https://doi.org/10.1016/j.geotexmem.2019.01.003.
Yoo, C. 2001. “Laboratory investigation of bearing capacity behavior of strip footing on geogrid-reinforced sand slope.” Geotext. Geomembr. 19 (5): 279–298. https://doi.org/10.1016/S0266-1144(01)00009-7.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 22 • Issue 9 • September 2022
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Nov 30, 2021
Accepted: May 14, 2022
Published online: Jun 29, 2022
Published in print: Sep 1, 2022
Discussion open until: Nov 29, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.