The Influence of Joint Inclination and Opening Width on Fracture Characteristics of Granite under Triaxial Compression
Publication: International Journal of Geomechanics
Volume 22, Issue 5
Abstract
Based on conventional triaxial compression tests, the influence of joint inclination (α) and opening width (t) on rock strength, deformation, and failure mode will be analyzed. Combining particle flow discrete–element (PFD) analysis, the fracture mechanism of jointed rock will be further investigated from the perspectives of microscopic crack evolution and energy conversion. The results show that as α increased, its peak strength (σc) presented a U-shaped change of first a decrease and then an increase, and it reached a minimum at approximately 60°, and its elastic modulus (E) exhibited an approximately linear monotonic increasing trend, and the ability to resist deformation gradually increased. For joint specimens with different opening widths, the strength and E exhibited similar evolution, and both decreased with the increase in opening width. As α increased, the failure mode changed from single inclined plane shear failure to an X-shaped conjugate inclined plane shear failure, and the increase in t resulted in a wider fracture zone. During rock failure, the number of microcracks accumulated in an S-shape, and its mutation point was consistent with the elastic, plastic, and failure characteristic points of the stress–strain curve. As the α angle enlarged, the external driving energy (Ew) first decreased and then increased, the ratio of dissipated energy (Ed) to Ew (Ed/Ew) decreased and tended to become stable. In triaxial compression, the frictional energy consumption of the microstructure surface accounted for ≤5%–20% of the total input energy, which indicated it should be considered during the analysis of fractures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded by the National Natural Science Foundation of China (Grant No. 42002275), Natural Science Foundation of Zhejiang Province (Grant Nos. LQ21D020001, LQ21E040003, and LQ20E040002), and Fellowship of China Postdoctoral Science Foundation (Grant No. 2021M692319).
References
Asadi, M. S., V. Rasouli, and G. Barla. 2012. “A bonded particle model simulation of shear strength and asperity degradation for rough rock fractures.” Rock Mech. Rock Eng. 45 (5): 649–675.
Barton, N., and V. Choubey. 1977. “The shear strength of rock joints in theory and practice.” Rock Mech. 10 (1–2): 1–54. https://doi.org/10.1007/BF01261801.
Bastola, S., and M. Cai. 2020. “Investigation of mechanical properties of jointed granite under compression using lattice-spring-based synthetic rock mass modeling approach.” Int. J. Rock Mech. Min. Sci. 126: 104191. https://doi.org/10.1016/j.ijrmms.2019.104191.
Cao, R. H., C. Ping, X. Fan, X. Xiong, and L. Hang. 2016. “An experimental and numerical study on mechanical behavior of ubiquitous-joint brittle rock-like specimens under uniaxial compression.” Rock Mech. Rock Eng. 49 (11): 1–20.
Chen, X., S. Zhang, and C. Cheng. 2018. “Numerical study on effect of joint strength mobilization on behavior of rock masses with large nonpersistent joints under uniaxial compression.” Int. J. Geomech. 18 (11): 04018140. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001260.
Cheung, L. Y. G., C. O’sullivan, and M. R. Coop. 2013. “Discrete element method simulations of analogue reservoir sandstones.” Int. J. Rock Mech. Min. Sci. 63: 93–103. https://doi.org/10.1016/j.ijrmms.2013.07.002.
Fairhurst, C. E., and J. A. Hudson. 1999. “Draft ISRM suggested method for the complete stress-strain curve for intact rock in uniaxial compression.” Int. J. Rock Mech. Min. Sci. 36 (3): 281–289.
Fan, H., S. Sun, J. Wei, H. Le, F. Zhu, W. Wang, Y. Liu, and J. Wang. 2021. “Shear behavior of soil–rock mixture composed of diorite-porphyrite considering weathering sequence.” Int. J. Geomech. 21 (7): 04021122.
Ge, Y. F., H. M. Tang, and L. Q. Wang. 2016. “Strain energy evolution of penetrative rock joints under shear loading.” Chin. J. Rock Mech. Eng. 35 (6): 1111–1121.
Hazzard, J. F., and R. P. Young. 2002. “Moment tensors and micromechanical models.” Tectonophysics 356 (1–3): 181–197. https://doi.org/10.1016/S0040-1951(02)00384-0.
Huang, D., D. F. Cen, and R. Q. Huang. 2013. “Influence of medium strain rate on sandstone with a single pre-crack under uniaxial compression using PFC simulation.” Rock Soil Mech. 34 (2): 535–545.
Holt, R. M., J. Kjølaas, I. Larsen, L. Li, A. G. Pillitteri, and E. F. Sønstebø. 2005. “Comparison between controlled laboratory experiments and discrete particle simulations of the mechanical behaviour of rock.” Int. J. Rock Mech. Min. Sci. 42 (7–8): 985–995. https://doi.org/10.1016/j.ijrmms.2005.05.006.
Jiang, Q., L. Song, F. Yan, C. Liu, B. Yang, and J. Xiong. 2020. “Experimental investigation of anisotropic wear damage for natural joints under direct shearing test.” Int. J. Geomech. 20 (4): 04020015. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001617.
Jing, H., Q. Yin, S. Yang, and W. Chen. 2021. “Micro-mesoscopic creep damage evolution and failure mechanism of sandy mudstone.” Int. J. Geomech. 21 (3): 04021010. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001940.
Kulatilake, P. H. S. W., B. Malama, and J. Wang. 2001. “Physical and particle flow modeling of jointed rock block behavior under uniaxial loading.” Int. J. Rock Mech. Min. Sci. 38 (5): 641–657. https://doi.org/10.1016/S1365-1609(01)00025-9.
Le, H., S. Sun, P. H. Kulatilake, and J. Wei. 2018. “Effect of grout on mechanical properties and cracking behavior of rock-like specimens containing a single flaw under uniaxial compression.” Int. J. Geomech. 18 (10): 04018129. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001225.
Lee, H., and S. Jeon. 2011. “An experimental and numerical study of fracture coalescence in pre-cracked specimens under uniaxial compression.” Int. J. Solids Struct. 48 (6): 979–999. https://doi.org/10.1016/j.ijsolstr.2010.12.001.
Li, Y., L. Song, Q. Jiang, C. Yang, C. Liu, and B. Yang. 2018. “Shearing performance of natural matched joints with different wall strengths under direct shearing tests.” Geotech. Test. J. 41 (2): 371–389.
Liu, X., W. Zhu, Y. Liu, Q. Yu, and K. Guan. 2021. “Characterization of rock joint roughness from the classified and weighted uphill projection parameters.” Int. J. Geomech. 21 (5): 04021052. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001963.
Luo, Y., G. Wang, X. Li, T. Liu, A. K. Mandal, M. Xu, and K. Xu. 2020. “Analysis of energy dissipation and crack evolution law of sandstone under impact load.” Int. J. Rock Mech. Min. Sci. 132: 104359. https://doi.org/10.1016/j.ijrmms.2020.104359.
Nasseri, M. H., K. S. Rao, and T. Ramamurthy. 1997. “Failure mechanism in schistose rocks.” Int. J. Rock Mech. Min. Sci. 34 (3–4): 219.e1–219.e15.
Park, J.-W., and J.-J. Song. 2009. “Numerical simulation of a direct shear test on a rock joint using a bonded-particle model.” Int. J. Rock Mech. Min. Sci. 46 (8): 1315–1328. https://doi.org/10.1016/j.ijrmms.2009.03.007.
Potyondy, D. O., and P. A. Cundall. 2004. “A bonded-particle model for rock.” Int. J. Rock Mech. Min. Sci. 41 (8): 1329–1364. https://doi.org/10.1016/j.ijrmms.2004.09.011.
Shi, C., W. Yang, J. Yang, and X. Chen. 2019. “Calibration of micro-scaled mechanical parameters of granite based on a bonded-particle model with 2D particle flow code.” Granular Matter 21 (2): 1–13.
Shi, C., B. Yang, Y. Zhang, and J. Yang. 2020. “Application of discrete-element numerical simulation for calculating the stability of dangerous rock mass: A case study.” Int. J. Geomech. 20 (12): 04020231. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001872.
Tao, Y., R. Wei, Q. Kunsheng, and W. Yundong. 2012. “Simulation of triaxial tests of marble samples through the particle flow code.” Soil Eng. Found. 26 (2): 70–73.
Wang, G., X. Zhang, Y. Jiang, X. Wu, and S. Wang. 2016. “Rate-dependent mechanical behavior of rough rock joints.” Int. J. Rock Mech. Min. Sci. 83: 231–240. https://doi.org/10.1016/j.ijrmms.2015.10.013.
Xiao, T. L., X. P. Li, and S. P. Jia. 2012. “Triaxial test research and mechanical analysis based on structure surface effect of deep rock mass with single fissure.” Chin. J. Rock Mech. Eng. 31 (8): 1666–1673.
Xie, H. P., R. D. Peng, Y. Ju, and H. W. Zhou. 2005. “Energy analysis of rock failure.” Chin. J. Rock Mech. Eng. 24 (15): 2603–2608.
Yang, S. Q., Y. Z. Jiang, W. Y. Xu, and X. Q. Chen. 2008. “Experimental investigation on strength and failure behavior of pre-cracked marble under conventional triaxial compression.” Int. J. Solids Struct. 45 (17): 4796–4819. https://doi.org/10.1016/j.ijsolstr.2008.04.023.
Yang, S.-Q., and H.-W. Jing. 2011. “Strength failure and crack coalescence behavior of brittle sandstone samples containing a single fissure under uniaxial compression.” Int. J. Fract. 168 (2): 227–250. https://doi.org/10.1007/s10704-010-9576-4.
Yoon, J. 2007. “Application of experimental design and optimization to PFC model calibration in uniaxial compression simulation.” Int. J. Rock Mech. Min. Sci. 44 (6): 871–889. https://doi.org/10.1016/j.ijrmms.2007.01.004.
Zhang, X., Y. Jiang, G. Wang, J. Liu, D. Wang, C. Wang, and S. Sugimoto. 2019. “Mechanism of shear deformation, failure and energy dissipation of artificial rock joint in terms of physical and numerical consideration.” Geosci. J. 23 (3): 519–529. https://doi.org/10.1007/s12303-018-0043-y.
Zhang, X.-P., and L. N. Y. Wong. 2014. “Choosing a proper loading rate for bonded-particle model of intact rock.” Int. J. Fract. 189 (2): 163–179. https://doi.org/10.1007/s10704-014-9968-y.
Zhao, C., B. E. Hobbs, A. Ord, P. Hornby, S. Peng, and L. Liu. 2007. “Particle simulation of spontaneous crack generation problems in large-scale quasi-static systems.” Int. J. Numer. Methods Eng. 69 (11): 2302–2329. https://doi.org/10.1002/nme.1851.
Zhou, X., L. Wang, and Y. Shou. 2020. “Understanding the fracture mechanism of ring Brazilian disc specimens by the phase field method.” Int. J. Fract. 226 (1): 17–43. https://doi.org/10.1007/s10704-020-00476-w.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Jun 11, 2021
Accepted: Dec 28, 2021
Published online: Feb 23, 2022
Published in print: May 1, 2022
Discussion open until: Jul 23, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Xiao Li, Xinquan Wang, Hongguo Diao, He Zhang, Chun Zhu, Influence of Depth and Position of Vibration-Isolating Slot on Damping Effect of Blasting Vibration, Shock and Vibration, 10.1155/2023/8492360, 2023, (1-11), (2023).
- Pengfei Lyu, Yijian Geng, Unified Mechanism of Rock Burst Induced by Coal Mine Earthquake and Its Activity and Response Characteristics, Shock and Vibration, 10.1155/2023/2145765, 2023, (1-14), (2023).
- Gang Wang, Xiqi Liu, Leibo Song, Xiaoming Ma, Wenzhao Chen, Jiaxing Qiao, Micro-structure and morphology of tailings sand under different oxidation and acidification degree, Scientific Reports, 10.1038/s41598-022-26130-0, 13, 1, (2023).
- Yunhe Ao, Baoxin Jia, Chuang Sun, Fengpu Liu, Fracture characteristics and energy evolution analysis of pre-cracked granite under uniaxial compression based on a 3D-Clump model, Theoretical and Applied Fracture Mechanics, 10.1016/j.tafmec.2023.103756, 124, (103756), (2023).
- Shuaidong Yang, Yueming Gao, Xiqi Liu, Gang Wang, Leibo Song, Chunyan Bao, Evolution of the Fracture Characteristics in a Rockburst under Different Stress Gradients, Buildings, 10.3390/buildings12111927, 12, 11, (1927), (2022).
- Botao Fei, Gang Wang, Xinping Li, Xiqi Liu, Leibo Song, Fracture and Damage Characteristics of Granite under Uniaxial Disturbance Loads, Buildings, 10.3390/buildings12071008, 12, 7, (1008), (2022).
- Pengfei Lyu, Kangbin Lu, Xuehua Chen, Mining Stress Distribution in Stope and Overlying Rock Fracture Characteristics and Its Disaster-Pregnant Mechanism of Coal Mine Earthquake, Shock and Vibration, 10.1155/2022/7606360, 2022, (1-17), (2022).
- Kun Xu, Leibo Song, Wenjie Song, Jiangtao He, Liping Li, Ge Yan, Qin Chen, Gang Wang, Research on Temporal and Spatial Distribution Characteristics of Microseismic Events of Slip-Type Rockburst, Shock and Vibration, 10.1155/2022/2262401, 2022, (1-15), (2022).
- Lichao Zhou, Gang Wang, Rong Hu, Xiqi Liu, Dongxing Wang, Leibo Song, Yong Niu, Study on the Failure Mechanism of Strain Rockburst, Shock and Vibration, 10.1155/2022/1663350, 2022, (1-12), (2022).
- Lijun Sun, Nanyan Hu, Yicheng Ye, Wenkan Tan, Menglong Wu, Xianhua Wang, Zhaoyun Huang, Ensemble stacking rockburst prediction model based on Yeo–Johnson, K-means SMOTE, and optimal rockburst feature dimension determination, Scientific Reports, 10.1038/s41598-022-19669-5, 12, 1, (2022).
- See more