Experimental Study on Mechanical Properties and Microcrack Fracture of Coal Specimens under the Coupling of Loading Rate and Compression–Shear Loads
Publication: International Journal of Geomechanics
Volume 22, Issue 4
Abstract
Gently inclined and inclined coal pillars are both subjected to the combined action of compression and shear load. Due to the existence of inclination angle, the fracture and instability behaviors of inclined pillars are different from those of near-horizontal pillars, and the difference is closely related to the load level of the pillar. Therefore, it is of great significance to study the influence of different inclination angles and loading rates on mechanical property and fracture behavior of the coal pillar for its strength design. In this paper, a new rock mechanical properties testing system was used with the combination of acoustic emission (AE) technology, and the changes of mechanical properties of coal specimens under different inclination angles and loading rates were obtained. The main conclusions are as follows: (1) the large of inclination angle, the greater of the peak shear stress. When the inclination angle is small (0°, 5°, 10°, and 15°), the peak stress increases first and then decreases with the increase of loading rate, when the inclination angle is large (20° and 25°), the peak stress gradually decreases. When the inclination angle is greater than 15°, the peak stress decreases with the increase of loading rate, and the decreasing amplitude gradually decreases. (3) The failure mode of the coal specimen is changed from tensile-splitting failure (0°–5°) and tension–shear composite failure (10°) to single shear failure (15°–25°). The loading rate has little effect on the failure mode of the specimen, but a significant effect on its failure degree. The crack initiation (CI) threshold and the crack damage (CD) threshold of coal specimens increase first and then decrease with the increase of inclination angle, and the ratios of CI and CD to peak strength are almost constant. With the increase of loading rate, the ratio of CI and CD to peak strength increases first and then decreases in the inclination angle range of 10°. The ratio of CI and CD to peak strength is basically independent of the loading rate. To comprehensively consider the influence of inclination angle and load level on pillar strength, a new parameter of rock strength under the influence of inclination angle and load level is suggested to be introduced into the empirical formula of pillar strength.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the Fundamental Research Funds for the Central Universities under Grant No. 2019XKQYMS53. The authors acknowledge the following contributions: Conceptualization, Peng Wu and Liang Chen; methodology, Yanlong Chen and Hai Pu; data curation, Xianbiao Mao and Kai Zhang; writing-original draft preparation, Xufeng Wang and Wei Zhang; writing-review and editing, Peng Wu.
References
Ahmed, S. S., M. Alheib, Y. Gunzburger, and V. Renaud. 2017. “Pillar burst assessment based on large-scale numerical modeling.” Procedia Eng. 191: 179–187. https://doi.org/10.1016/j.proeng.2017.05.170.
Ai, T., R. Zhang, J. Liu, and L. Ren. 2012. “Space–time evolution rules of acoustic emission location of unloaded coal specimen at different loading rates.” Int. J. Min. Sci. Technol. 22 (6): 847–854. https://doi.org/10.1016/j.ijmst.2012.12.001.
Amann, F., P. Kaiser, and E. A. Button. 2012. “Experimental study of brittle behavior of clay shale in rapid triaxial compression.” Rock Mech. Rock Eng. 45 (1): 21–33. https://doi.org/10.1007/s00603-011-0195-9.
Benz, T., and R. Schwab. 2008. “A quantitative comparison of six rock failure criteria.” Int. J. Rock Mech. Min. Sci. 45 (7): 1176–1186. https://doi.org/10.1016/j.ijrmms.2008.01.007.
Bieniawski, Z. T. 1967a. “Mechanism of brittle fracture of rock: Part II.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 4 (4): 407–423. https://doi.org/10.1016/0148-9062(67)90031-9.
Bieniawski, Z. T. 1967b. “Mechanism of brittle fracture of rock: Part I.” J. Rock Mech. Min. Sci. 47: 723–738.
Brace, W. F., B. W. Paulding, and C. Scholz. 1966. “Dilatancy in the fracture of crystalline rocks.” J. Geophys. Res. 71 (16): 3939–3953. https://doi.org/10.1029/JZ071i016p03939.
Cai, M., H. Morioka, P. K. Kaiser, Y. Tasaka, H. Kurose, M. Minami, and T. Maejima. 2007. “Back-analysis of rock mass strength parameters using AE monitoring data.” Int. J. Rock Mech. Min. Sci. 44 (4): 538–549. https://doi.org/10.1016/j.ijrmms.2006.09.012.
Cai, M., P. K. Kaiser, Y. Tasaka, T. Maejima, H. Morioka, and M. Minami. 2004. “Generalized crack initiation and crack damage stress thresholds of brittle rock masses near underground excavations.” Int. J. Rock Mech. Min. Sci. 41 (5): 833–847. https://doi.org/10.1016/j.ijrmms.2004.02.001.
Chang, S. H., and C. Lee. 2004. “Estimation of cracking and damage mechanisms in rock under triaxial compression by moment tensor analysis of acoustic emission.” Int. J. Rock Mech. Min. Sci. 41 (7): 1069–1086. https://doi.org/10.1016/j.ijrmms.2004.04.006.
Chen, L., X. B. Mao, and P. Wu. 2020a. “Effect of high temperature and inclination angle on mechanical properties and fracture behavior of granite at low strain rate.” Sustainability 12 (3): 1255. https://doi.org/10.3390/su12031255.
Chen, L., P. Wu, Y. Chen, and W. Zhang. 2020b. “Experimental study on physical–mechanical properties and fracture behaviors of saturated yellow sandstone considering coupling effect of freeze–thaw and specimen inclination.” Sustainability 12 (3): 1029. https://doi.org/10.3390/su12031029.
Chen, Y., H. Cui, H. Pu, P. Wu, L. Chen, and K. Zhang. 2020c. “Study on mechanical properties and cracking mode of coal samples under compression–shear coupled load considering the effect of loading rate.” Appl. Sci. 10 (20): 7082. https://doi.org/10.3390/app10207082.
Cho, G.-C., J.-S. Kim, W.-J. Cho, H.-J. Choi, and K.-S. Lee. 2015. “A comparative evaluation of stress–strain and acoustic emission methods for quantitative damage assessments of brittle rock.” Rock Mech. Rock Eng. 48 (2): 495–508. https://doi.org/10.1007/s00603-014-0590-0.
RILEM Technical Committee. 2010. “Recommendation of RILEM TC 212-ACD: Acoustic emission and related NDE techniques for crack detection and damage evaluation in concrete.” Mater. Struct. 43 (9): 1187–1189. https://doi.org/10.1617/s11527-010-9640-6.
Eberhardt, E., D. Stead, and B. Stimpson. 1999a. “Quantifying progressive pre-peak brittle fracture damage in rock during uniaxial compression.” Int. J. Rock Mech. Min. Sci. 36 (3): 361–380. https://doi.org/10.1016/S0148-9062(99)00019-4.
Eberhardt, E., B. Stimpson, and D. Stead. 1999b. “Effects of grain size on the initiation and propagation thresholds of stress-induced brittle fractures.” Rock Mech. Rock Eng. 32 (2): 81–99. https://doi.org/10.1007/s006030050026.
Feng, X., N. Zhang, X. Zheng, and D. Pan. 2015. “Strength restoration of cracked sandstone and coal under a uniaxial compression test and correlated damage source location based on acoustic emissions.” PLoS One 10 (12): e0145757.
Geng, J., and L. Cao. 2020. “Failure analysis of water-bearing sandstone using acoustic emission and energy dissipation.” Eng. Fract. Mech. 231: 107021. https://doi.org/10.1016/j.engfracmech.2020.107021.
Geng, J., Q. Sun, Y. Zhang, L. Cao, and W. Zhang. 2017. “Studying the dynamic damage failure of concrete based on acoustic emission.” Constr. Build. Mater. 149: 9–16. https://doi.org/10.1016/j.conbuildmat.2017.05.054.
He, M. C., F. Zhao, M. Cai, and S. Du. 2015. “A novel experimental technique to simulate pillar burst in laboratory.” Rock Mech. Rock Eng. 48 (5): 1833–1848. https://doi.org/10.1007/s00603-014-0687-5.
He, M. C., J. L. Miao, and J. L. Feng. 2010. “Rock burst process of limestone and its acoustic emission characteristics under true-triaxial unloading conditions.” Int. J. Rock Mech. Min. Sci. 47 (2): 286–298. https://doi.org/10.1016/j.ijrmms.2009.09.003.
He, Q., Y. Li, and S. She. 2019. “Mechanical properties of basalt specimens under combined compression and shear loading at low strain rates.” Rock Mech. Rock Eng. 52 (10): 4101–4112. https://doi.org/10.1007/s00603-019-01806-8.
Hedley, D., and F. Grant. 1972. Stope-and-pillar design for the Elliot Lake Uranium mines. Montreal: Canadian Institute of Mining, Metallurgy and Petroleum.
Kimmelmann, M., B. Hyde, and R. J. Madgwick. 1984. “7 the use of computer applications at BCL Limited in planning pillar extraction and the design of mining layouts.” In Proc., Design and Performance of Underground Excavations: ISRM Symp., edited by E. T. Brown and J. A. Hudson. London: Thomas Telford.
Li, T. H., L. Song, H. W. Zhou, Y. D. Jiang, and H. W. Wang. 2015. “Evaluation method and application of coal burst performance under the effect of loading rate.” J. China Coal Soc. 40: 21–29.
Liu, B., Z. Shu, J. Han, M. Liu, and K. Zhang. 2012. “Real-time CT experimental research on creep microscopic damage evolution of coal rock under compression.” Disaster Adv. 5 (4): 667–674.
Lunder, P. J., and R. C. Pakalnis. 1997. “Determination of the strength of hard-rock mine pillars.” CIM Bull. 90 (1013): 51–55.
Martin, C. D., and N. A. Chandler. 1994. “The progressive fracture of Lac du Bonnet granite.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 31 (6): 643–659. https://doi.org/10.1016/0148-9062(94)90005-1.
Munro, A. H., and M. D. G. Salamon. 1967. “A study of the strength of coal pillars.” J. South. Afr. Inst. Min. Metall. 68 (2): 55–67.
Nicksiar, M., and C. D. Martin. 2014. “Factors affecting crack initiation in low porosity crystalline rocks.” Rock Mech. Rock Eng. 47 (4): 1165–1181. https://doi.org/10.1007/s00603-013-0451-2.
Nie, X., and W. Chen. 2007. “Dynamic failure of a borosilicate glass under compression/shear loading.” In Vol. 28 of Advances in ceramic armor III: Ceramic and engineering science proceedings, edited by L. P. Franks, J. Salem, and D. Zhu, 103–111. Hoboken, NJ: Wiley.
Ning, Z. X. 2011. “Generation mechanism of coal pillar rock burst.” Appl. Mech. Mater. 90–93: 33–36. https://doi.org/10.4028/www.scientific.net/AMM.90-93.33.
Niu, S., H. Jing, D. Yang, and J. Guo. 2015. “Experimental study on strength characteristics and deformation behavior of the cracked rock samples under uniaxial compression.” J. Min. Saf. Eng, 32 (1): 112–118.
Pariseau, W. G. 1982. “Shear stability of mine pillars In dipping seams.” In Proc., 23rd US Symp. on Rock Mechanic, 198225–198227. Houston: American Rock Mechanics Association.
Rastiello, G., F. Federico, and S. Screpanti. 2015. “New soft rock pillar strength formula derived through parametric FEA using a critical state plasticity model.” Rock Mech. Rock Eng. 48 (5): 2077–2091. https://doi.org/10.1007/s00603-014-0693-7.
Schmidtke, R. H., and E. Z. Lajtai. 1985. “The long-term strength of Lac du Bonnet granite.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 22 (6): 461–465. https://doi.org/10.1016/0148-9062(85)90010-5.
Shkuratnik, V. L., Y. L. Filimonov, and S. V. Kuchurin. 2004. “Experimental investigations into acoustic emission in coal samples under uniaxial loading.” J. Min. Sci. 40 (5): 458–464. https://doi.org/10.1007/s10913-005-0030-3.
Suorineni, F. T., P. K. Kaiser, J. J. Mgumbwa, and D. Thibodeau. 2013. “Mining of orebodies under shear loading—Part 1: Case histories.” Min. Technol. 120 (3): 137–147. https://doi.org/10.1179/1743286311Y.0000000012.
Suorineni, F. T., J. J. Mgumbwa, P. K. Kaiser, and D. Thibodeau. 2014. “Mining of orebodies under shear loading—Part 2: Failure modes and mechanisms.” Min. Technol. IMM Trans. Sect. A 123 (4): 240–249.
Walsh, J. B. 1965. “The effect of cracks on the uniaxial elastic compression of rocks.” J. Geophys. Res. 70 (2): 399–411. https://doi.org/10.1029/JZ070i002p00399.
Wang, M., W. Wan, and Y. Zhao. 2020a. “Experimental study on crack propagation and the coalescence of rock-like materials with two preexisting fissures under biaxial compression.” Bull. Eng. Geol. Environ. 79 (6): 3121–3144. https://doi.org/10.1007/s10064-020-01759-1.
Wang, Q., J. Chen, J. Guo, Y. Luo, and Q. Liu. 2020b. “Strain rate effect on acoustic emission characteristics and energy mechanisms of Karst limestone under uniaxial compression.” Adv. Mater. Sci. Eng. 2020 (1): 6871902. https://doi.org/10.1155/2020/6871902.
Wang, X., Z. Wen, Y. Jiang, and H. Huang. 2018. “Experimental study on mechanical and acoustic emission characteristics of rock-like material under non-uniformly distributed loads.” Rock Mech. Rock Eng. 51 (3): 729–745. https://doi.org/10.1007/s00603-017-1363-3.
Wang, Z. H., J. C. Wang, S. L. Yang, L. H. Li, and M. Li. 2020c. “Failure behaviour and acoustic emission characteristics of different rocks under uniaxial compression.” J. Geophys. Eng. 17 (1): 76–88.
Xin, S., W. Liu, W. Chen, and D. Templeton. 2009. “Modeling and characterization of dynamic failure of borosilicate glass under compression/shear loading.” Int. J. Impact Eng. 36 (2): 226–234. https://doi.org/10.1016/j.ijimpeng.2008.01.014.
Xu, S., J. Huang, P. Wang, C. Zhang, L. Zhou, and S. Hu. 2015. “Investigation of rock material under combined compression and shear dynamic loading: An experimental technique.” Int. J. Impact Eng. 86: 206–222. https://doi.org/10.1016/j.ijimpeng.2015.07.014.
Xu, Y., and F. Dai. 2018. “Dynamic response and failure mechanism of brittle rocks under combined compression–shear loading experiments.” Rock Mech. Rock Eng. 51 (3): 747–764. https://doi.org/10.1007/s00603-017-1364-2.
Xue, Y., Z. Cao, and Z. Li. 2020. “Destabilization mechanism and energy evolution of coal pillar in rockburst disaster.” Arabian J. Geosci. 13 (13): 557.
Yang, S. Q., W. L. Tian, Y. H. Huang, P. G. Ranjith, and Y. Ju. 2016. “An experimental and numerical study on cracking behavior of brittle sandstone containing two non-coplanar fissures under uniaxial compression.” Rock Mech. Rock Eng. 49 (4): 1497–1515. https://doi.org/10.1007/s00603-015-0838-3.
Yang, S. Q., Y. H. Dai, L. J. Han, and Z. Q. Jin. 2009. “Experimental study on mechanical behavior of brittle marble samples containing different flaws under uniaxial compression.” Eng. Fract. Mech. 76 (12): 1833–1845. https://doi.org/10.1016/j.engfracmech.2009.04.005.
Yang, S. Q., H. M. Ni, and S. Wen. 2014. “Spatial acoustic emission evolution of red sandstone during multi-stage triaxial deformation.” J. Cent. South Univ. 21 (8): 3316–3326. https://doi.org/10.1007/s11771-014-2305-9.
Yang, Y. U., K. Deng, and H. Fan. 2017. “Long-term stability evaluation and coal pillar design methods for strip mining.” J. China Coal Soc. 42 (12): 3089–3095.
Zhao, X. G., M. Cai, J. Wang, P. F. Li, and L. K. Ma. 2015. “Objective determination of crack initiation stress of brittle rocks under compression using AE measurement.” Rock Mech. Rock Eng. 48 (6): 2473–2484. https://doi.org/10.1007/s00603-014-0703-9.
Zhi, G., M. Chen, J. Yan, Y. Shuai, and X. Du. 2016. “Experimental study of brittleness anisotropy of shale in triaxial compression.” J. Nat. Gas Sci. Eng. 36: 510–518. https://doi.org/10.1016/j.jngse.2016.10.059.
Zhou, H. W., Z. H. Wang, C. S. Wang, and J. F. Liu. 2019a. “On acoustic emission and post-peak energy evolution in Beishan granite under cyclic loading.” Rock Mech. Rock Eng. 52 (1): 283–288. https://doi.org/10.1007/s00603-018-1614-y.
Zhou, Z. L., H. Z. Zang, W. Z. Cao, X. M. Du, L. Chen, and C. T. Ke. 2019b. “Risk assessment for the cascading failure of underground pillar sections considering interaction between pillars.” Int. J. Rock Mech. Min. Sci. 124: 104142.
Zong, Y., L. Han, J. Wei, and S. Wen. 2016. “Mechanical and damage evolution properties of sandstone under triaxial compression.” Int. J. Min. Sci. Technol. 26 (4): 601–607. https://doi.org/10.1016/j.ijmst.2016.05.011.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: May 17, 2021
Accepted: Nov 3, 2021
Published online: Feb 4, 2022
Published in print: Apr 1, 2022
Discussion open until: Jul 4, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Lan Wang, Peng Wu, Ming Li, Xianbiao Mao, Liang Chen, Mechanical Properties and Acoustic Emission Characteristics of Water-Bearing Coal Specimens under a Coupled Compression–Shear Load, Minerals, 10.3390/min12060704, 12, 6, (704), (2022).
- Hanqing Wang, Li Li, Xinwang Li, Lichao Cheng, Pengfei Shen, Study on Crack Evolution and Failure Mechanism of Fully Penetrated Fracture Grouting Body, Geofluids, 10.1155/2022/9424120, 2022, (1-22), (2022).
- Chong Li, Sifeng He, Zhijun Xu, Experimental Investigation on Long-Term Strength and Acoustic Emission Characteristics of Coal Pillar under Inclined Compression Loading, Geofluids, 10.1155/2022/1213215, 2022, (1-17), (2022).