Evolution of Natural Joints' Mesoscopic Failure Modes under Shear Tests: Acoustic Emission Investigation
Publication: International Journal of Geomechanics
Volume 21, Issue 11
Abstract
Natural joints play an important role in the stability performance of rock engineering. To deeply understand the shear mechanism of natural joints (i.e., tensile fracture or shear fracture), direct shear experiments and acoustic emission (AE) monitoring were carried out for different kinds of joints under five levels of normal stress. By disposing the AE signals during a joint's shear process as AE samples databases, an optimal criterion to identify the tensile fracture and shear fracture modes was established based on the AE parameters, and this method was applied to reveal the shear damage of natural joints under the shear process. The results showed that the shear failure regions of natural joints were localized and inhomogeneous on a joint's surface, and the mesoscopic shear fracture and tensile fracture appeared along all the shearing process of the joint. The moment and the type of failure mode changed with the increase of the normal stress, but the main type of fracture did not change in each period during the whole shearing process, which provided a new way for disaster warning of shear damage.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge financial support from the National Natural Science Foundation of China (Nos. U1965205 and 51779251).
References
Aggelis, D. G. 2011. “Classification of cracking mode in concrete by acoustic emission parameters.” Mech. Res. Commun. 38 (3): 153–157. https://doi.org/10.1016/j.mechrescom.2011.03.007.
Aggelis, D. G., D. V. Soulioti, N. Sapouridis, N.-M. Barkoula, A. S. Paipetis, and T. E. Matikas. 2011a. “Acoustic emission characterization of the fracture process in fibre reinforced concrete.” Constr. Build. Mater. 25 (11): 4126–4131. https://doi.org/10.1016/j.conbuildmat.2011.04.049.
Aggelis, D. G., N. Tsimpris, H. K. Chai, T. Shiotani, and Y. Kobayashi. 2011b. “Numerical simulation of elastic waves for visualization of defects.” Constr. Build. Mater. 25 (4): 1503–1512. https://doi.org/10.1016/j.conbuildmat.2010.08.008.
Atapour, H., and M. Moosavi. 2014. “The influence of shearing velocity on shear behavior of artificial joints.” Rock Mech. Rock Eng. 47 (5): 1745–1761. https://doi.org/10.1007/s00603-013-0481-9.
Aydan, Ö., R. Ulusay, and N. Tokashiki. 2014. “A new rock mass quality rating system: Rock mass quality rating (RMQR) and its application to the estimation of geomechanical characteristics of rock masses.” Rock Mech. Rock Eng. 47 (4): 1255–1276. https://doi.org/10.1007/s00603-013-0462-z.
Barton, N. 1973. “Review of a new shear-strength criterion for rock joints.” Eng. Geol. 7 (4): 287–332. https://doi.org/10.1016/0013-7952(73)90013-6.
Barton, N. 1976. “Shear-strength of rock and rock joints.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 13 (9): 255–279. https://doi.org/10.1016/0148-9062(76)90003-6.
Bruneau, G., M. R. Hudyma, J. Hadjigeorgiou, and Y. Potvin. 2003. “Influence of faulting on a mine shaft—a case study: Part II—Numerical modelling.” Int. J. Rock Mech. Min. Sci. 40 (1): 113–125. https://doi.org/10.1016/S1365-1609(02)00116-8.
Chen, N., X. Zhang, Q. Jiang, X. Feng, W. Wei, and B. Yi. 2018. “Shear behavior of rough rock joints reinforced by bolts.” Int. J. Geomech. 18 (1): 04017130. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001048.
Feng, G.-L., X.-T. Feng, B.-R. Chen, X. Yaxun, and Z.-N. Zhao. 2019. “Effects of structural planes on the microseismicity associated with rockburst development processes in deep tunnels of the Jinping-II Hydropower Station, China.” Tunnelling Underground Space Technol. 84: 273–280. https://doi.org/10.1016/j.tust.2018.11.008.
Ghazvinian, A., R. G. Vaneghi, M. R. Hadei, and M. J. Azinfar. 2013. “Shear behavior of inherently anisotropic rocks.” Int. J. Rock Mech. Min. Sci. 61: 96–110. https://doi.org/10.1016/j.ijrmms.2013.01.009.
Goodman, R. 1976. Methods of geological engineering in discontinuous rocks. Stavanger, Norway: West Group.
Goodman, R. 1989. An introduction to rock mechanics. New York: Wiley.
Hao, Y. H., and R. Azzam. 2005. “The plastic zones and displacements around underground openings in rock masses containing a fault.” Tunnelling Underground Space Technol. 20 (1): 49–61. https://doi.org/10.1016/j.tust.2004.05.003.
Homand, F., T. Belem, and M. Souley. 2001. “Friction and degradation of rock joint surfaces under shear loads.” Int. J. Numer. Anal. Methods Geomech. 25 (10): 973–999. https://doi.org/10.1002/nag.163.
Hu, J., S. Li, H. Liu, L. Li, S. Shi, and C. Qin. 2020. “New modified model for estimating the peak shear strength of rock mass containing nonconsecutive joint based on a simulated experiment.” Int. J. Geomech. 20 (7): 04020091. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001732.
Huang, T. H., C. S. Chang, and C. Y. Chao. 2002. “Experimental and mathematical modeling for fracture of rock joint with regular asperities.” Eng. Fract. Mech. 69 (17): 1977–1996. https://doi.org/10.1016/S0013-7944(02)00072-3.
Hudson, J. A., J. P. Harrison, and M. E. Popescu. 2002. “Engineering rock mechanics: An introduction to the principles.” Appl. Mech. Rev. 55 (2): B30. https://doi.org/10.1115/1.1451165.
Hudson, J. A., and S. D. Priest. 1983. “Discontinuity frequency in rock masses.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 20 (2): 73–89. https://doi.org/10.1016/0148-9062(83)90329-7.
Jiang, Q., X.-T. Feng, G. Yanhua, L. Song, S. Ran, and J. Cui. 2016. “Reverse modelling of natural rock joints using 3D scanning and 3D printing.” Comput. Geotech. 73: 210–220. https://doi.org/10.1016/j.compgeo.2015.11.020.
Jiang, Q., X. Liu, F. Yan, Y. Yang, D. Xu, and G. Feng. 2020a. “Failure performance of 3DP physical twin-tunnel model and corresponding safety factor evaluation.” Rock Mech. Rock Eng. 54 (1): 109–128. https://doi.org/10.1007/s00603-020-02244-7.
Jiang, Q., L. Song, F. Yan, C. Liu, B. Yang, and J. Xiong. 2020b. “Experimental investigation of anisotropic wear damage for natural joints under direct shearing test.” Int. J. Geomech. 20 (4): 04020015. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001617.
Jiang, Q., B. Yang, F. Yan, C. Liu, Y. Shi, and L. Li. 2020c. “New method for characterizing the shear damage of natural rock joint based on 3D engraving and 3D scanning.” Int. J. Geomech. 20 (2): 06019022. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001575.
Kumar, R., and A. K. Verma. 2016. “Anisotropic shear behavior of rock joint replicas.” Int. J. Rock Mech. Min. Sci. 90: 62–73. https://doi.org/10.1016/j.ijrmms.2016.10.005.
Li, Y., W. Wu, C. A. Tang, and B. Liu. 2019. “Predicting the shear characteristics of rock joints with asperity degradation and debris backfilling under cyclic loading conditions.” Int. J. Rock Mech. Min. Sci. 120: 108–118. https://doi.org/10.1016/j.ijrmms.2019.06.001.
Li, Y., H. Zhou, W. Zhu, S. Li, and J. Liu. 2016. “Experimental and numerical investigations on the shear behavior of a jointed rock mass.” Geosci. J. 20 (3): 371–379. https://doi.org/10.1007/s12303-015-0052-z.
Liu, X., L. Wu, Y. Zhang, Z. Liang, X. Yao, and P. Liang. 2019. “Frequency properties of acoustic emissions from the dry and saturated rock.” Environ. Earth Sci. 78 (3): 67. https://doi.org/10.1007/s12665-019-8058-x.
Lockner, D. 1993. “The role of acoustic emission in the study of rock fracture.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 30 (7): 883–899. https://doi.org/10.1016/0148-9062(93)90041-B.
Moosavi, M., H. N. Rafsanjani, M. H. Mehranpour, A. Nazem, and A. Navabi. 2013. “An investigation of surface roughness measurement in rock joints with a 3D scanning device.” In ISRM SINOROCK 2013, 119–130. London: Taylor and Francis.
Muralha, J., G. Grasselli, B. Tatone, M. Blumel, P. Chryssanthakis, and Y. Jiang. 2014. “ISRM suggested method for laboratory determination of the shear strength of rock joints: Revised version.” Rock Mech. Rock Eng. 47 (1): 291–302. https://doi.org/10.1007/s00603-013-0519-z.
Nazarchuk, Z., V. Skalskyi, and O. Serhiyenko. 2017. “Propagation of elastic waves in solids.” In Acoustic emission: Methodology and application, 29–73. Cham, Switzerland: Springer International Publishing.
Nguyen-Tat, T., N. Ranaivomanana, and J.-P. Balayssac. 2018. “Characterization of damage in concrete beams under bending with acoustic emission technique (AET).” Constr. Build. Mater. 187: 487–500. https://doi.org/10.1016/j.conbuildmat.2018.07.217.
Ohno, K., and M. Ohtsu. 2010. “Crack classification in concrete based on acoustic emission.” Constr. Build. Mater. 24 (12): 2339–2346. https://doi.org/10.1016/j.conbuildmat.2010.05.004.
Ohtsu, M. 2008. Acoustic emission testing. Berlin: Springer.
Ohtsu, M., T. Isoda, and Y. Tomoda. 2007. “Acoustic emission techniques standardized for concrete structures.” J. Acoust Emission 25: 21–32.
Ohtsu, M., T. Shiotani, and M. Shigeishi. 2010. “Recommendation of RILEM TC 212-ACD: Acoustic emission and related NDE techniques for crack detection and damage evaluation in concrete.” Mater. Struct. 43 (9): 1187–1189. https://doi.org/10.1617/s11527-010-9640-6.
Pei, J., W. Fei, and J. Liu. 2016. “Spatial evolution and fractal characteristics of natural fractures in marbles under uniaxial compression loading based on the source location technology of acoustic emission.” Environ. Earth Sci. 75 (9): 828. https://doi.org/10.1007/s12665-016-5649-7.
Prem, P. R., A. R. Murthy, and M. Verma. 2018. “Theoretical modelling and acoustic emission monitoring of RC beams strengthened with UHPC.” Constr. Build. Mater. 158: 670–682. https://doi.org/10.1016/j.conbuildmat.2017.10.063.
Sagar, R. V., Mohit, S. Deepak, and P. R. Desai. 2019. “Statistical analysis of acoustic emissions generated during unconfined uniaxial compression of cementitious materials.” Constr. Build. Mater. 225: 692–708. https://doi.org/10.1016/j.conbuildmat.2019.07.195.
Saiful Bahari, M., S. Shahidan, S. Abdullah, N. Ali, S. S. Mohd Zuki, M. H. Ibrahim, and M. Abdul Rahim. 2017. “Crack classification in concrete beams using AE parameters.” IOP Conf. Ser.: Mater. Sci. Eng. 271: 012090. https://doi.org/10.1088/1757-899X/271/1/012090.
Seidel, J. P., and C. M. Haberfield. 1995. “The application of energy principles to the determination of the sliding resistance of rock joints.” Rock Mech. Rock Eng. 28 (4): 211–226. https://doi.org/10.1007/BF01020227.
Shen, Y., Y. Wang, Y. Yang, Q. Sun, T. Luo, and H. Zhang. 2019. “Influence of surface roughness and hydrophilicity on bonding strength of concrete-rock interface.” Constr. Build. Mater. 213: 156–166. https://doi.org/10.1016/j.conbuildmat.2019.04.078.
Son, M., and S. Adedokun. 2015. “Effect of support characteristics on the earth pressure in a jointed rock mass.” Can. Geotech. J. 52 (12): 1956–1967. https://doi.org/10.1139/cgj-2014-0437.
Soulioti, D., N.-M. Barkoula, A. Paipetis, T. E. Matikas, T. Shiotani, and D. G. Aggelis. 2009. “Acoustic emission behavior of steel fibre reinforced concrete under bending.” Constr. Build. Mater. 23: 3532–3536. https://doi.org/10.1016/j.conbuildmat.2009.06.042.
Tayfur, S., and N. Alver. 2019. “A 3D parameter correction technique for damage assessment of structural reinforced concrete beams by acoustic emission.” Constr. Build. Mater. 215: 148–161. https://doi.org/10.1016/j.conbuildmat.2019.04.140.
Tsangouri, E., and D. G. Aggelis. 2019. “A review of acoustic emission as indicator of reinforcement effectiveness in concrete and cementitious composites.” Constr. Build. Mater. 224: 198–205. https://doi.org/10.1016/j.conbuildmat.2019.07.042.
Ulusay, R., and H. Karakul. 2016. “Assessment of basic friction angles of various rock types from Turkey under dry, wet and submerged conditions and some considerations on tilt testing.” Bull. Eng. Geol. Environ. 75 (4): 1683–1699. https://doi.org/10.1007/s10064-015-0828-4.
Vahaviolos, S. J. 2019. Acoustic emission: Standards and technology update. ASTM Special Technical Publication No. 1353. West Conshohocken, PA: ASTM.
Xia, C.-C., Z. C. Tang, W.-M. Xiao, and Y.-L. Song. 2014a. “New peak shear strength criterion of rock joints based on quantified surface description.” Rock Mech. Rock Eng. 47 (2): 387–400. https://doi.org/10.1007/s00603-013-0395-6.
Xia, C., Y. Gui, W. Wang, and S. Du. 2014b. “Numerical method for estimating void spaces of rock joints and the evolution of void spaces under different contact states.” J. Geophys. Eng. 11 (6): 065004. https://doi.org/10.1088/1742-2132/11/6/065004.
Yue, J. G., S. K. Kunnath, and Y. Xiao. 2020. “Uniaxial concrete tension damage evolution using acoustic emission monitoring.” Constr. Build. Mater. 232: 117281. https://doi.org/10.1016/j.conbuildmat.2019.117281.
Zhao, Y., L. Zhang, W. Wang, Q. Liu, L. Tang, and G. Cheng. 2020. “Experimental study on shear behavior and a revised shear strength model for infilled rock joints.” Int. J. Geomech. 20 (9): 04020141. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001781.
Zhu, J. B., H. Li, and J. H. Deng. 2019. “A one-dimensional elastoplastic model for capturing the nonlinear shear behaviour of joints with triangular asperities based on direct shear tests.” Rock Mech. Rock Eng. 52 (6): 1671–1687. https://doi.org/10.1007/s00603-018-1674-z.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 27, 2020
Accepted: Jun 3, 2021
Published online: Aug 26, 2021
Published in print: Nov 1, 2021
Discussion open until: Jan 26, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Yujing Jiang, Xinpeng Li, Changsheng Wang, Hengjie Luan, Sunhao Zhang, Gang Wang, Pu Wang, Influence of Normal Stiffness and Shear Rate on the Shear Behaviors and Acoustic Emissions Characteristics of Artificial Rock Joints, Applied Sciences, 10.3390/app13021189, 13, 2, (1189), (2023).
- Chang Liu, Guang-Liang Feng, Chun Zhu, Ding-Ping Xu, Failure Characteristics and Scale in a Sandstone Joint Subjected to Direct Shear Testing: Experimental Investigation with Acoustic Emission Monitoring, Lithosphere, 10.2113/2022/6456423, 2022, Special 10, (2022).
- Yongchun Zhao, Shuangyang Li, Lianghong Shi, Jiale Yang, Jianyuan Zhao, Mechanical Damage Evolution and a Statistical Damage Model for Frozen Sandstone, International Journal of Geomechanics, 10.1061/(ASCE)GM.1943-5622.0002541, 22, 10, (2022).